Abstract:The thermal deformation behavior of oxidation products formed on Fe–Si alloys with varying Si contents was systematically investigated using a thermal simulation testing machine during compressive deformation at temperatures ranging from 800 to 1100 °C. It is found that the higher the deformation temperature is, the better the plasticity of the oxide product is, and the better the deformation coordination between the oxidation product and the substrate, where the deformation mainly occurs in the FeO layer. The increase of Si content reduces the coordination of deformation between the oxidation product and the substrate, but it can improve the interface straightness. The crystal structure of the oxidation product determines its plastic deformation ability, and the deformation mechanism of FeO is determined by the dislocation slip and climb, and its plastic deformation ability is the best. The dislocation slip dominates the deformation mechanism of Fe 3 O 4 , and the deformation ability is the second, and Fe 2 O 3 has basically no plastic deformation ability. Therefore, the increase of the Si content leads to the reduction of the proportion of the FeO layer in the oxidation product, which is the main reason for the decrease of the deformation coordination between the oxidation product and the substrate. As Si element forms a spinel solid solution composed of Fe 2 SiO 4 with FeO and SiO 2 at the interface, it has good plastic deformation ability and can deform synchronously with the substrate, and the porous structure can effectively relieve the compressive stress during deformation, which can effectively improve the interface straightness. In addition, the increase of Si content makes the concentration of iron ions in FeO close to the substrate side lower, which causes the increase of point defect concentration to promote the dislocation climbing of FeO, and makes the steady-state plastic deformation ability of FeO close to the substrate side higher, which improves the straightness of the interface between the oxidation product and the substrate.

Effect of Si Content and Temperature on Oxidation Resistance of Fe-Si Alloys

Effect of Temperature on Structure of Outer Fe Oxide Layer of Fe-2.2Si Alloy

Oxidation Mechanism of Three Fe-Al Alloys with and Without Addition of 0.1 At% Yttrium at 800 °C

Oxidation Behavior of Quaternary Co-20Re-25Cr-3Si Alloy at Laboratory Air

Oxidation behavior of AlCoCrFeNiSi high-entropy alloys at 1100 °C

Study on the high-temperature oxidation of AlCrFeCoNi-based high-entropy alloys with trace Si additions

The Effects of Alloying Elements Cr, Al, and Si on Oxidation Behaviors of Ni-Based Superalloys

High‐Temperature Oxidation of Fe–Si Alloys in Atmospheres Containing 2.0% SO2 + 5.0% O2

Effect of aluminium and silicon on high temperature oxidation resistance of Fe-Cr-Ni heat resistant steel

Investigation of Selective Oxidation During Cooling of Hot-Rolled Iron-Manganese-silicon Alloys

High-Temperature Oxidation Behavior of Fe-1Cr-0.2Si Steel

Enhancing oxidation resistance with Si in Fe36Ni36Al15Cr10Si2Mo1 multi-principal element alloy at 700 °C

Effect of Si Content on Deposition and High-Temperature Oxidation of Al-Si Coatings Obtained by Magnetron Sputtering PVD Method

New insights in the oxidation behavior of (FeCoCrNi)94Al4Ti2Si high entropy alloys at 1100 °C

Effect of Si element on improving the oxidation resistance of hybrid (Ti5Si3 + TiC) particles reinforced Ti6Al4V matrix composites

Influence of oxidation temperature on microstructure and electromagnetic performance of Fe-Si/Fe2SiO4 soft magnetic composites

Investigation of the Thermal Deformation Behavior Exhibited by Oxidation Products in Fe–Si Alloys

High temperature oxidation behavior of binary Co-10Si alloys

The Influence of FeO on the Reaction between Fe–Al–Ca Alloy and Al2O3–CaO–FeO Oxide during Heat Treatment at 1473 K

Oxidation of Fe-Ni Alloys in Air at 700°C, 800°C and 950°C

The effect of silicon on the oxidation behavior of iron aluminide produced using powder metallurgy