Abstract:The thermal deformation behavior of oxidation products formed on Fe–Si alloys with varying Si contents was systematically investigated using a thermal simulation testing machine during compressive deformation at temperatures ranging from 800 to 1100 °C. It is found that the higher the deformation temperature is, the better the plasticity of the oxide product is, and the better the deformation coordination between the oxidation product and the substrate, where the deformation mainly occurs in the FeO layer. The increase of Si content reduces the coordination of deformation between the oxidation product and the substrate, but it can improve the interface straightness. The crystal structure of the oxidation product determines its plastic deformation ability, and the deformation mechanism of FeO is determined by the dislocation slip and climb, and its plastic deformation ability is the best. The dislocation slip dominates the deformation mechanism of Fe 3 O 4 , and the deformation ability is the second, and Fe 2 O 3 has basically no plastic deformation ability. Therefore, the increase of the Si content leads to the reduction of the proportion of the FeO layer in the oxidation product, which is the main reason for the decrease of the deformation coordination between the oxidation product and the substrate. As Si element forms a spinel solid solution composed of Fe 2 SiO 4 with FeO and SiO 2 at the interface, it has good plastic deformation ability and can deform synchronously with the substrate, and the porous structure can effectively relieve the compressive stress during deformation, which can effectively improve the interface straightness. In addition, the increase of Si content makes the concentration of iron ions in FeO close to the substrate side lower, which causes the increase of point defect concentration to promote the dislocation climbing of FeO, and makes the steady-state plastic deformation ability of FeO close to the substrate side higher, which improves the straightness of the interface between the oxidation product and the substrate.

Effect of Temperature on Structure of Outer Fe Oxide Layer of Fe-2.2Si Alloy

Effect of Si Content and Temperature on Oxidation Resistance of Fe-Si Alloys

High‐Temperature Oxidation of 60si2mn Spring Steel in Dry Air and Wet Air: Insights from an Experimental and First‐Principles Study

Oxidation Mechanism of Three Fe-Al Alloys with and Without Addition of 0.1 At% Yttrium at 800 °C

High-Temperature Oxidation Behavior of Fe-1Cr-0.2Si Steel

High‐Temperature Oxidation of Fe–Si Alloys in Atmospheres Containing 2.0% SO2 + 5.0% O2

The Effect of Heat Treatments on the Microstructural Evolution of Twin-Roll-Cast Al-Fe-Si Alloys

High Temperature Oxidation of Fe-Cr Alloys in Atmospheres Containing 2.0 % SO2+5.0 % O2

Investigation of Selective Oxidation During Cooling of Hot-Rolled Iron-Manganese-silicon Alloys

High-temperature oxidation mechanism of Fe-3.0 wt%Si electrical steel with hybrid atmosphere

Comparative Study On Oxidation Behavior Of Fe-5wt% Cr Alloy In Various Mixed Atmospheres At 900-1000 Degrees C

Comparative Study on Oxidation Behavior of Fe-5wt% Cr Alloy in Various Mixed Atmospheres at 900–1 000 °C

Characterization of Oxide Scales Formed on Plain Carbon Steels in Dry and Wet Atmospheres and Their Eutectoid Transformation from FeO in Inert Atmosphere

Isothermal Structure Transformation and Kinetics Behavior of Oxide Scale on Low Carbon Steel

Effect of aluminium and silicon on high temperature oxidation resistance of Fe-Cr-Ni heat resistant steel

Descaling Abilities of Two Low-Alloy High-Strength Steels Under Different Heating Processes

Oxidation behavior of AlCoCrFeNiSi high-entropy alloys at 1100 °C

Investigation of oxide scale formation and internal oxidation of an Fe-based coating at 500 °C and 600 °C

Investigation of the Thermal Deformation Behavior Exhibited by Oxidation Products in Fe–Si Alloys

Formation and disappearance of an internal oxidation zone in the initial stage of the steam oxidation of Fe–9Cr–0.26Si ferritic steel

Iron oxide fluxing and precipitation in sulphate deposits during heat-resistant alloy corrosion in simulated combustion gas