Abstract:In this study, using synchrotron radiation X-ray imaging, the microstructure, tensile properties, and fatigue properties of FGH96 nickel-based superalloy were tested, and the fatigue damage mechanism was analyzed. An analysis of the experimental results shows that the alloy structure is dense without voids or other defects. It was observed that the primary γ' phase is distributed on the grain boundary in a chain shape, and the secondary γ' phase is found inside the crystal grains. The X-ray diffraction (XRD) pattern indicates that no other phases were seen except for the γ and γ' phases. The tensile strength of the alloy is 1570 MPa and the elongation is 12.1%. Using data fitting and calculation, it was found that the fatigue strength of the alloy under the condition of 5 × 106 cycles is 620.33 MPa. A fatigue fracture has the characteristics of secondary crack, cleavage step, fatigue stripe, tire indentation, and dimple. The fracture is a mix of cleavage fracture and ductile fracture. Through a three-dimensional reconstruction of the alloy synchrotron radiation imaging area, it was found that the internal defects are small and mostly distributed at the edge of the sample. The dimple morphology is formed by cavity aggregation and cavity germination resulting from defects in the material itself, fracture of the second-phase particles, and separation of the second-phase particles from the matrix interface. By analyzing the damage mechanism of fatigue fractures, it is concluded that the cleavage step is formed by the intersection of cleavage planes formed by branch cracks, with the main crack of the confluence extending forward to form a cleavage fracture. The crack propagation path was also analyzed, and under the action of cyclic load and tip passivation, the crack shows Z-shaped propagation.

High Temperature Low Cycle Fatigue Behavior of GH4742 Alloy

Low cycle fatigue behavior of nickel-based superalloy GH4145/SQ at elevated temperature

Effect of cyclic straining at elevated-temperature on static mechanical properties, microstructures and fracture behavior of nickel-based superalloy GH4145/SQ

Effect of Initial Overload on the Low Cycle Fatigue Life of Gh4169 Alloy at Different Temperatures

An Investigation of the Effect of High-Temperature Cyclic Straining and Creep Loading on Tensile Mechanical Properties of GH4145/SQ Alloy

Investigation of fatigue mesoscopic mechanical properties of a nickel-based superalloy by instrumented microindentation measurements

Use of Instrumented Micro-Indentation to Study the Mesoscopic Elasto-Plastic Behavior of Gh4145/Sq Superalloy During High-Temperature Cyclic Straining

High-Temperature Low-Cycle Fatigue Properties of GH4169 Ni-based Superalloy

Influence of Strain Amplitude on Low-Cycle Fatigue Behaviors of a Fourth-Generation Ni-Based Single-Crystal Superalloy at 980 °C

High Temperature Low-Cycle Fatigue, Deformation Microstructure and Final Fracture Behavior of a Nickel-Base Superalloy

Microstructures' Effects on High Temperature Fatigue Failure Behavior of Typical Superalloys

Effects of Heat Treatment on Microstructure and Low Cycle Fatigue Life of GH4169 Alloy

High Cycle Fatigue Behavior of Inertia Friction Welded Joint of FGH96 Alloy at High Temperature

Combined high and low cycle fatigue analysis of FGH96 alloy under high temperature conditions

Low Cycle Fatigue and High Cycle Fatigue of K4750 Ni-based Superalloy at 600 °C: Analysis of Fracture Behavior and Deformation Mechanism

Crack initiation mechanisms and life prediction of GH4169 superalloy in the high cycle and very high cycle fatigue regime

Very high cycle fatigue behaviors of GH4169 superalloy at room and high temperatures

Low Cycle Fatigue Properties of FGH97 P/M Superalloy with Different Test Control Modes

Cyclic Deformation Behavior of a Nickel-Base Superalloy under Fatigue Loading

Study on Microstructure and Fatigue Properties of FGH96 Nickel-Based Superalloy

Effect of Heat Treatment on High-Temperature Low-Cycle Fatigue Behavior of Nickel-Based GH4169 Alloy