Abstract:Polypropylene double‐grafted maleic anhydride and bisphenol A epoxy resin (PPg‐M‐E) was prepared and used as compatibilizer for PP/PET blends. The thermomechanical and morphology of the composites were characterized. The results show that PP‐g‐M‐E increased the interfacial interaction between the two phases and improves the mechanical properties and thermal stability of the blend system. Polypropylene double‐grafted maleic anhydride and bisphenol A epoxy resin (PP‐g‐M‐E) was successfully prepared by a single‐step method and characterized by Fourier‐transform infrared spectroscopy. Subsequently, it was employed as a compatibilizer to fabricate polypropylene (PP)/polyethylene terephthalate (PET) blends via melt extrusion. The content of the PET dispersed phase in the composite varied from 0 to 30 phr. The microstructure and morphology of the composites were characterized using scanning electron microscopy and Raman spectroscopy. The addition of PP‐g‐M‐E increased the interfacial interaction between the two phases and improved the compatibility and thermal stability of the system. In the presence of the compatibilizer, the crystallinity of the matrix phase (PP) increased, while that of the dispersed phase (PET) decreased owing to the heterogeneous nucleation effect of uniformly distributed PET. Double grafting of the PP‐g‐M‐E compatibilizer considerably enhanced the mechanical performance of the PP/PET blend system. The elongation at break of the modified sample exceeded that of the PP/PET blends by 117.55%, and the flexural and impact properties also showed considerable improvement.

Application of Macromolecular Chain Extender and Contribution to the Toughening of Poly(Ethylene Terephthalate)

Toughening of Poly(ethylene Terephthalate) and Optimizing of the Compatibilization Between PET and EPDM by Functionalized EPDM

Poly(ethylene 2,5-Furandicarboxylate-mb-poly(tetramethylene Glycol)) Multiblock Copolymers: from High Tough Thermoplastics to Elastomers

Toughening PET/PC Blends with Ethylene-propylene-diene Rubber

Preparation and Properties of Poly(Ethylene Terephthalate)/Poly(Butylene Terephthalate) Alloys with High Toughness

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Mutual Nucleating and Crystallization Behavior of Poly (ethylene Terephthalate)/polyamide 66 Blends

Toughening of PBT by POE/POE-g-GMA Elastomer Through Regulating Interfacial Adhesion and Toughening Mechanism

Toughening of poly(butylene terephthalate) with epoxidized ethylene propylene diene rubber

Effect of chain extender on the morphological, rheological and mechanical properties of biodegradable blends from PBAT and P34HB

Enhancement of physical properties of thermoplastic polyether-ester elastomer by reactive extrusion with chain extender

Fabrication of poly(ethylene terephthalate)/polypropylene-based elastomer blends with balanced stiffness-toughness: The effect of reactive compatibilization

Design of super-toughened, heat-resistant and antistatic polyethylene terephthalate-based blend composites by constructing a tenacious interface

Molecular dynamics simulation and experimental study on the mechanical properties of PET nanocomposites filled with CaCO 3 , SiO 2 , and POE- g -GMA

Preparation and Properties of Poly(ethylene glycol-co-cyclohexane-1,4-dimethanol terephthalate)/Polyglycolic Acid (PETG/PGA) Blends

Study of polypropylene/polyethylene terephthalate blends compatibilized with polypropylene double‐grafted maleic anhydride and epoxy resin

Toughening of Pbt/Pc Blends with Epoxy Functionalized Core-Shell Modifiers

Fabrication of improved overall properties of poly (ethylene terephthalate) by simultaneous chain extension and crystallization promotion

Impacts of chain extenders on thermal property, degradation, and rheological performance of poly(butylene adipate-co-terephthalate)

A facile approach to realize simultaneously chain extension and crystallization promotion of poly (ethylene terephthalate)

Chain Extension of Polyester PBT with Epoxide Resin