Abstract:Polypropylene double‐grafted maleic anhydride and bisphenol A epoxy resin (PPg‐M‐E) was prepared and used as compatibilizer for PP/PET blends. The thermomechanical and morphology of the composites were characterized. The results show that PP‐g‐M‐E increased the interfacial interaction between the two phases and improves the mechanical properties and thermal stability of the blend system. Polypropylene double‐grafted maleic anhydride and bisphenol A epoxy resin (PP‐g‐M‐E) was successfully prepared by a single‐step method and characterized by Fourier‐transform infrared spectroscopy. Subsequently, it was employed as a compatibilizer to fabricate polypropylene (PP)/polyethylene terephthalate (PET) blends via melt extrusion. The content of the PET dispersed phase in the composite varied from 0 to 30 phr. The microstructure and morphology of the composites were characterized using scanning electron microscopy and Raman spectroscopy. The addition of PP‐g‐M‐E increased the interfacial interaction between the two phases and improved the compatibility and thermal stability of the system. In the presence of the compatibilizer, the crystallinity of the matrix phase (PP) increased, while that of the dispersed phase (PET) decreased owing to the heterogeneous nucleation effect of uniformly distributed PET. Double grafting of the PP‐g‐M‐E compatibilizer considerably enhanced the mechanical performance of the PP/PET blend system. The elongation at break of the modified sample exceeded that of the PP/PET blends by 117.55%, and the flexural and impact properties also showed considerable improvement.

Toughening of Poly(ethylene Terephthalate) and Optimizing of the Compatibilization Between PET and EPDM by Functionalized EPDM

Toughening PET/PC Blends with Ethylene-propylene-diene Rubber

Application of Macromolecular Chain Extender and Contribution to the Toughening of Poly(Ethylene Terephthalate)

Toughening of poly(butylene terephthalate) with epoxidized ethylene propylene diene rubber

Poly(ethylene 2,5-Furandicarboxylate-mb-poly(tetramethylene Glycol)) Multiblock Copolymers: from High Tough Thermoplastics to Elastomers

Preparation and Properties of Poly(Ethylene Terephthalate)/Poly(Butylene Terephthalate) Alloys with High Toughness

Fabrication of poly(ethylene terephthalate)/polypropylene-based elastomer blends with balanced stiffness-toughness: The effect of reactive compatibilization

Polymer Blends of Pbt and Pp Compatibilized by Epoxidized Ethylene Propylene Diene Rubber

Toughened poly(butylene terephthalate) by epoxided ethylene-propylene-diene-rubber

Toughening of PBT by POE/POE-g-GMA Elastomer Through Regulating Interfacial Adhesion and Toughening Mechanism

Study of polypropylene/polyethylene terephthalate blends compatibilized with polypropylene double‐grafted maleic anhydride and epoxy resin

Toughening of Poly(butylene Terephthalate) with Epoxy-Functionalized Acrylonitrile–butadiene–styrene

Toughening of Pbt/Pc Blends with Epoxy Functionalized Core-Shell Modifiers

Influence of the Degree of Grafting on the Morphology and Mechanical Properties of Blends of Poly(butylene Terephthalate) and Glycidyl Methacrylate Grafted Poly(ethylene‐co‐propylene) (EPR)

Properties of Poly(butylene Terephthalate)/bisphenol A Polycarbonate Blends Toughening with Epoxy-Functionalized Acrylonitrile–Butadiene–Styrene Particles

Preparation of PBT/POE‐g‐GMA/PP Ternary Blends with Good Rigidity–toughness Balance by Core–shell Particles

Toughening of Polylactide with Epoxy-Functionalized Methyl Methacrylate-Butadiene Copolymer

Toughening of Polystyrene with Ethylene-Propylene-Diene Terpolymer(EPDM) Compatibilized by Styrene-Butadiene-Styrene Block Copolymer(SBS)

Synergistic Effect of Polycarbonate on Reactive Core-Shell Particles Toughened Poly (butylene Terephthalate)

Dynamically photocrosslinking of polypropylene/EPDM blends as a thermoplastic elastomer

Molecular dynamics simulation and experimental study on the mechanical properties of PET nanocomposites filled with CaCO 3 , SiO 2 , and POE- g -GMA