Abstract:Porous Si2N2O/SiC ceramics is facilitated at 1200 °C for 10 min by microwave sintering. Rapid in‐situ production of Si2N2O fibers provided high mechanical properties of the samples. The porosity of the prepared sample is tailorable and the thermal insulation effect is excellent. Two steps strategy were taken to effectively produce porous Si2N2O/SiC ceramics: 1) direct foaming combined with sol‐gel curing at room temperature to form a green body, and 2) sintering assisted by in‐situ production of Si2N2O fibers under microwave sintering conditions. Non‐toxic silica sol was used to provide silicon source for in‐situ synthesis of Si2N2O, the silica sol could form a gel that stabilizes the bubbles, creating a porous structure. A thorough investigation was conducted into how different sintering temperatures affected the microstructure, flexural strength, and porosity of the porous Si2N2O/SiC composites. The main bonding phase in the porous composites was the Si2N2O with fiber morphology. The optimal microwave sintering temperature for fabricating porous Si2N2O/SiC ceramics, using a combination of sol‐gel and direct foaming techniques, has been determined to be 1200 °C. At this temperature, the porosity can be controlled between 73.32% and 83.16% by proportionally adjusting the ratio of the raw materials. Under the condition of high porosity, the thermal radiation is dominant and the thermal conductivity increases with the increase of temperature. With the decrease of porosity, the heat conduction is dominant, and the thermal conductivity decreases with the increase of temperature.

Mechanical, Dielectric Properties and Thermal Shock Resistance of Porous Silicon Oxynitride Ceramics by Gas Pressure Sintering

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Fabrication and properties of porous boron nitride/silicon oxynitride ceramic composites via gas pressure sintering

Fabrication and properties of Si2N2O ceramics for microwave sintering furnace

Mechanical and Dielectric Properties of Si2N2O Ceramics Prepared by Pressureless Sintering

Mechanical, dielectric and thermal properties of porous boron nitride/silicon oxynitride ceramic composites prepared by pressureless sintering

Effect of pre-oxidation on the microstructure, mechanical and dielectric properties of highly porous silicon nitride ceramics

Properties of porous Si3N4 ceramic electromagnetic wave transparent materials prepared by technique combining freeze drying and oxidation sintering

Porosity and Oxide Layer Dependence of Thermal Shock Behavior of Porous Silicon Nitride Ceramics

Preparation of Si2N2O wave-transparent and thermal insulation materials with Na2CO3 and BN as aids by pressureless sintering

Silicon Nitride Ceramics Consolidated by Oscillatory Pressure Sintering

Preparation And Properties Of High Strength Porous Si3n4 Ceramics

Non-additive sintering of Si2N2O ceramic with enhanced high-temperature strength, oxidation resistance, and dielectric properties

Microstructure, Mechanical and Dielectric Properties of Highly Porous Silicon Nitride Ceramics Produced by a New Water-Based Freeze Casting

Optimum Sintering Temperature of High Quality Silicon Nitride Ceramics under Oscillatory Pressure

Mechanical and dielectric properties of porous Si3N4 ceramics prepared by modified water‐based gel casting

Dielectric constant, dielectric loss and thermal conductivity of Si3N4 ceramics by hot pressing with CeO2–MgO as sintering aid

Microstructure and properties of porous Si3N4 ceramics by gelcasting-self-propagating high-temperature synthesis (SHS)

Effect of Diatomite Additive on the Mechanical and Dielectric Properties of Porous SiO2-Si3N4 Composite Ceramics

Preparation of Porous Si2N2O/SiC Ceramics by Microwave Sintering

The Fabrication, Mechanical Property And Oxidation Of Si3n4 Ceramics With Rare Earth Oxide Addition