Abstract:{1011}-{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150°C and 300°C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s -1. Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {1011}-{1012} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins. © Right.

Modified Twinning Behaviour Induced by Texture Evolution in Hot Rolled Mg–3Al–1Zn Alloy

Reducing the anisotropy of a pre-twinned hot-rolled Mg-3Al-1Zn alloy by plane-strain compression

Twinning Behavior of a Strongly Basal Textured AZ31 Mg Alloy During Warm Rolling

Twinning characteristic and variant selection in compression of a pre-side-rolled Mg alloy sheet

Twinning, Grain Orientation, and Texture Variations in Mg Alloy Processed by Pre-Rolling

Microstructure, Texture and Mechanical Properties Evolution of Pre-Twinning Mg Alloys Sheets During Large Strain Hot Rolling

Twinning-mediated Texture Weakening in a Basal-Textured Mg-6Al-1Zn (mass%) Alloy Sheet by a Novel Cold-Sample Rolling Method

Twinning and Mechanical Behavior of an Extruded Mg–6Al–3Sn Alloy with a Dual Basal Texture

Texture weakening and ductility improvement of Mg-1.1Mn-0.5Al alloy via medium temperature-high reduction rolling: twinning variants selection and dynamic recrystallization mechanism

Observation and Schmid Factor Analysis of Multiple Twins in a Warm-Rolled Mg–3Al–1Zn Alloy

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

The Role of Al Content on Deformation Behavior and Related Texture Evolution During Hot Rolling of Mg-Al-Zn Alloys

Twinning-Assisted Static Recrystallization and Texture Evolution in A Mg-Gd-Y-Zr Alloy

Twinning Behavior in a Rolled Mg-Al-Zn Alloy under Dynamic Impact Loading

Twinning character and texture origination in the randomly-oriented AZ31B magnesium alloy during cold-rolling

Influence of Pre-Twinning on High Strain Rate Compressive Behavior of AZ31 Mg-alloys

Loading Mode Dependence of {$$10\bar{1}2$$} Twin Variant Selection in a Rolled Mg-Al-Zn Alloy

Influence of Twinning-Induced Recrystallization on Texture Evolution in a High Strain Rate Compressed Mg-Zn Alloy

Multiple-twinning induced recrystallization and texture optimization in a differential-temperature-rolled AZ31B magnesium alloy with excellent ductility

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Reducing the Tension–compression Yield Asymmetry in a Hot-Rolled Mg–3Al–1Zn Alloy Via Multidirectional Pre-Compression