Abstract:Carburization of iron was studied at atmospheric pressure over the temperature range 850 degrees C to 1150 degrees C in gaseous mixtures of CO, H-2, and He. The resistance relaxation method was applied to measure the carburization rates. Experimental results show that for carburization in CO-He mixtures, the carburization rate increased proportionally with CO partial pressure with a reaction order of unity. The overall rate also increased with temperature up to approximately 960 degrees C and subsequently decreased with further increases in temperature. For carburization in CO-H-2-He mixtures, the carburization rate increased with both the CO and H-2 partial pressures under most conditions and was considerably faster than the rate in mixtures without hydrogen. Up to approximately 960 degrees C, the rate was nearly independent of temperature with H-2 present, but decreased with a further increase in temperature. The decrease in reaction rate for mixtures with and without H-2 at 960 degrees C coincides closely with the change in phase of iron from alpha to gamma. Experiments at 925 degrees C with constant PH2 and PCO indicate that CO dissociation on the iron surface is faster than oxygen removal from the surface except at high ratios of PH2/PCO, and therefore oxygen removal was generally the rate-limiting step. The rate of oxygen removal from the surface by H-2 was found to be of the same order as that by CO. At high hydrogen levels, the rate of oxygen removal exceeds dissociative absorption of CO and the latter becomes rate controlling. The present results are used to establish a numerical model for the carburization of iron, which is described in a companion paper. (C) 2009 Wiley Periodicals, Inc. Int J Chem Kinet 41: 327-336, 2009

Iron carburization in CO‐H2‐He gases, Part II: Numerical model

Iron Carburization In Co-H-2-He Gases, Part I: Experiment

A Thorough Theoretical Exploration of the Effect Mechanism of Fe on HCN Heterogeneous Formation from Nitrogen-Containing Char

Modeling of the HiPco process for carbon nanotube production. I. Chemical kinetics

Numerical Simulation Study of Co-injection of Pulverized Coal and Hydrogen in the Tuyere-Raceway

Experimental Study and Computer Simulation on Multicomponent Diffusion in Multiphase Dispersions During Solid Carburizing of HP40Nb and KHR45A Alloys

Phase Composition and Numerical Model of Low-Pressure Pulse Carburized Layer in 15cr14co12mo5ni2w Steel

Modeling of the HiPco process for carbon nanotube production. II. Reactor-scale analysis

Experimental and Modeling Study on Reduction and Heat Transfer Characteristics of Single Iron Ore Pellet in H<sub>2</sub>/CO Atmospheres

Iron Carbidization on Thin-Film Silica and Silicon: A Near-Ambient-Pressure X-ray Photoelectron Spectroscopy and Scanning Tunneling Microscopy Study

Thermodynamic, Kinetic and Mechanical Modeling to Evaluate CO2-induced Corrosion via Oxidation and Carburization in Fe, Ni alloys

Thermodynamic, Kinetic and Mechanical Modeling to Evaluate CO 2 -induced Corrosion via Oxidation and Carburization in Fe, Ni alloys

Mathematical Modeling of Decarburization in Levitated Fe-Cr-C Droplets

Kinetic Mechanism Development for the Direct Reduction of Single Hematite Pellets in H2/CO Atmospheres

The role of H2 in Fe carburization by CO in Fischer-Tropsch catalysts

Investigation of methane decomposition and carburization with iron: the combination of a ReaxFF molecular dynamics simulation and experimental work

Experimental and Modeling Investigation of Oxy-Coal Combustion Based on Langmuir-Hinshelwood Kinetics and Direct Calculation of Char Morphology

Effect of Temperature on CH4/CO Carburization Process of Hydrogen‐Based Direct Reduced Iron Pellets

Computational modeling of oxy-coal combustion with intrinsic heterogeneous char reaction models

Simultaneous Oxidation and Carburization of a Fe-9Cr Alloy under Different Oxygen Pressures at 800 °C