Abstract:Micron-sized iron particles are promising carbon-free fuels. Efforts have been made to understand the combustion process of pure iron particles. However, it is not well-established how important are the impurities and their influence on combustion. The ignition and combustion characteristics of iron particles with 6.18 wt.% silicon were studied both by online optical diagnostics and offline scanning electron microscope (SEM) and X-ray Diffraction (XRD) analysis in this work. It is found that the ignition delay time is proportional to dn with n=1.23∼1.56 , indicating that the oxidation reaction is unlikely solely limited by internal ionic diffusion before ignition. Compared with pure iron particles, the silicon-containing iron particle has a lower peak temperature and less oxidized combustion products. The intensity-rising time in the first intensity peak stage scales (1/XO2)n with n=0.80or1.38 , which implies an external diffusion controlled combustion regime. Silicon in the oxide layer likely reduces the internal diffusion rate of oxygen, which becomes a rate-limiting step after the first intensity peak. Meanwhile, the surface tension also decreases due to the silicon content, which may facilitate the gas bubble nucleation and burst. The particle could partially change back to the external diffusion regime when the oxide layer is broken by the bubble expansion. This mechanism allows the reaction rate to increase and particle temperature to rise again. This explanation is verified by plenty of holes in the combustion products as well as the fact that the rising time in the large peak stage is proportional to (1/XO2)n with n=0.37or0.32 . With the increase in the temperature of the ambient gas flow, evaporation was observed. The high ambient temperature is hypothesized to be a key factor to trigger the evaporation of silica.

Iron Carbidization on Thin-Film Silica and Silicon: A Near-Ambient-Pressure X-ray Photoelectron Spectroscopy and Scanning Tunneling Microscopy Study

Surface Coordinate Geometry of Iron Catalysts: Formation of Tetrahedral/Octahedral Site on Silica Surface with/without Sodium Promoter

Iron Carburization In Co-H-2-He Gases, Part I: Experiment

Reaction of Iron with Amorphous Silicon and Crystal Silicon for the Fabrication of Iron Silicides

Interfacial Phenomenon and Marangoni Convection of Fe–C Melt on Coke Substrate under in Situ Observation

Carbon monoxide adsorption on cobalt overlayers on a Si(1 1 1) surface studied by STM and XPS

Carbon monoxide adsorption on cobalt overlayers on a Si(111) surface studied by STM and XPS

A Study of the Solid State Reaction Between Silicon Carbide and Iron

Relationship Between Iron Carbide Phases (Epsilon-Fe2c, Fe7C3, and Chi-Fe5c2) and Catalytic Performances of Fe/SiO2 Fischer-Tropsch Catalysts

Silicon Carbide-Supported Iron Nanoparticles Encapsulated In Nitrogen-Doped Carbon For Oxygen Reduction Reaction

Direct environmental TEM observation of silicon diffusion-induced strong metal-silica interaction for boosting CO2 hydrogenation

Atomically Defined Iron Carbide Surface for Fischer–Tropsch Synthesis Catalysis

Carbon Deposition on Iron Surfaces in CO–CO2atmosphere

Controlled Formation of Iron Carbides and Their Performance in Fischer-Tropsch Synthesis

Catalytic Performance of Iron Oxide Loaded on Electron-Rich Surfaces of Carbon Nitride

Ignition and combustion of a single iron particle with impurities in hot post-flame gas flow

Visualizing Electronic Interactions Between Iron and Carbon by X-ray Chemical Imaging and Spectroscopy.

The role of H2 in Fe carburization by CO in Fischer-Tropsch catalysts

Iron carbide formation on thin iron films grown on Cu(1 0 0): FCC iron stabilized by a stable surface carbide

Atomic Diffusion in the Interface of Fe/Si Prepared by Magnetron Sputtering

Carbon-supported Iron Catalysts: Iron-57 Mössbauer Spectroscopic Studies of Phase Formation and Dispersion Properties Which Influence Catalytic Performance