Abstract:Nickel based superalloys are widely used in such applications as gas turbine blades due to their excellent mechanical properties at elevated temperatures. Oxidation is one of the life limiting factors at such temperatures since it accelerates failure mechanisms, e.g. fatigue and creep. In this project, oxidation behavior of Ni-3Al-4.8Ti-9.5Co-14Cr (wt.%) superalloy was investigated under various testing conditions. The alloy was investment-cast with preferential crystal growth direction [100]. Isothermal oxidation tests were carried out at 800°C for 150h. Cyclic oxidation tests were then conducted between 100-800°C for 150 one-hour cycles. An additional one-hour cycle was tested to replicate real-life working condition of the alloy, which consisted of heating the samples up to 800°C followed by slow cooling to 400°C. During the testing, samples were periodically taken from the furnace and weighted with an accuracy of 10 -4 g to calculate the weight gain and to analyze the microstructure of formed oxide. Scanning electron microscopy (SEM) combined with energy-dispersive spectroscopy (EDS) and X-ray diffraction were used to study the microstructure of oxidation products. The results reveal that the highest amount of weight gain is obtained in isothermal testing, while the lowest in cyclic. Diffusion of Ti and Ni to the free surface results in the early-stage formation of needle-shaped oxide phases followed by severe oxidation of Cr and Al. The layer of chromium oxide is continuous while aluminum oxide is blocky at the deepest position from the free surface. Cracks form at the interface of carbide particles and gamma phase near the free surface of cyclic oxidation samples due to concentration gradient of Ni and Al. Precipitate-free zone are observed near the free surface of all the samples at the end of the tests, but internal oxidation does not occur significantly in all the samples. It is found that temperature fluctuation increases oxide spallation, which causes crack formation. At the same time, in isothermal testing, dense, crack-free layer of oxide form on the surface of superalloy.

Cyclic Oxidation of Ternary Layered Ti2AlC at 600–1000°C in Air

Thermal Oxidation Behaviour of Ti6Al7Nb and Ti6Al4V Alloys

Oxidation Behavior of TiC-containing Ti3AlC2based Material at 500–900 °C in Air

Oxidizing Characteristics and Oxide Formation of V-4cr-4ti Alloy

Improvement of Intermediate-Temperature Oxidation Resistance of Ti3AlC2 by Pre-Oxidation at High Temperatures

Surface Characterization of Thermally Oxidized Titanium Alloys

Oxidation Resistance of In Situ Reaction/Hot Pressing Synthesized Ti2AlC–20% TiB2 Composite at 600–900 °C in Air

Oxidation Behavior of Ternary Carbide Ceramics in Hf–Al–C System in Air

Microstructure evolution during oxidation of quinary Ti 3 (AlSiSn)C 2 at high temperatures and induced probable performance

The Oxidation Behaviour of Tic Matrix Ni3al and Fe40al Toughened Composites at High Temperatures

Insights into High Temperature Oxidation of Al2O3-forming Ti3AlC2

Oxidation behavior and mechanism of Al4O4C powders at 1000–1300 °C

Oxidation Behavior of TiAl(Cr, Ag) at 900 °C in Water Vapor

High Temperature Oxidation Behaviors of Al/Cr Composite Coating on Ti2AlNb Alloy

OXIDATION MECHANISM OF BINARY Ti-Al ALLOYS AT ELEVATED TEMPERATURE

Microstructural evolution and high-temperature oxidation mechanisms of a titanium aluminide based alloy

High Temperature Oxidation Resistance Of Ti3sic2 In Air And Low Oxygen Atmosphere

Cyclic and Isothermal Oxidation Behavior of a Directionally Solidified Ni-Al-Ti-Co-Cr Superalloy

Mechanisms responsible for enhancing low‐temperature oxidation resistance of nonstoichiometric (Zr,Ti)C

Influence Mechanism of Cu on High Temperature Oxidation Behavior of Titanium Alloys

Thermodynamic and microstructural study of Ti2AlNb oxides at 800 °C