Abstract:Ceramic coatings with aluminum titanuate (Al2TiO5) were prepared on Ti–6Al–4V alloy using pulsed bi-polar Micro-arc Oxidation (MAO). The micromorphology and phase composition of the micro-arc-oxidition ceramic coatings on the titanium alloy were characterized by X-ray powder diffraction (XRD), and scanning electron microscopy (SEM) respectively. The results revealed that the distinct discharge channels and pores on the surface of the micro-arc-oxidition coatings appeared, and these channels were connected in the molten state. The electrolyte concentration was inversely proportional to the coating hardness; additionally, the coating prepared with sodium aluminate and sodium hypophosphite concentrations of 4 g/L and 0.5 g/L, respectively, was the most refined after high-temperature sintering, and it was demonstrated to better prevent oxidation. Increasing the electrolyte concentration coincided with fluctuating coating thermal shock resistance. The thermal shock resistance of the coating respectively prepared with sodium aluminate, and the sodium hypophosphite concentrations of 4 g/L and 0.5 g/L was the highest. Additionally, the high-concentration coatings performed significantly better than the low-concentration coatings. The oxidation resistance of the coating samples was also significantly higher than that of the TC4 titanium alloy substrate. The adhesion strength between the coatings and the substrate with and without the sealing treatment was measured by tensile tests. Then, the high-temperature oxidation performance of the coating samples with and without the sealing treatment was investigated by conducting a high-temperature oxidation experiment at a calcinating temperature of 500 °C. The results indicate that the adhesion strength between the coatings and substrate was high for the as-prepared and sealed micro-arc oxidation samples regardless of whether they were calcined. The high-temperature oxidation mass increase curves for the sealed and unsealed coating samples calcined at 500 °C for 500 h revealed that the high-temperature-oxidation-induced mass increase of the coating samples sealed with a sodium silicate solution was much lower than that of the titanium alloy substrate. Thus, the sealing treatment significantly improved the high-temperature oxidation resistance of the TC4 titanium alloy. Lastly, the high-temperature oxidation behavior at 500 °C was analyzed and discussed.

Surface Characterization of Thermally Oxidized Titanium Alloys

Thermal Oxidation Behaviour of Ti6Al7Nb and Ti6Al4V Alloys

Characterization of the Surface Oxygen-Diffusion Zone of the Thermally Oxidized Titanium

Effect of Oxidation Time on the Structure and Properties of Ti-25Nb-3Zr-2Sn-3Mo Titanium Alloy Microarc Oxide Film Layer

Characterization of Microarc Oxidation Coatings on Pure Titanium

Structure and properties characterization of ceramic coatings produced on Ti–6Al–4V alloy by microarc oxidation in aluminate solution

Characterization of Oxide Coatings Deposited on Pure Titanium by Alternating-Current Microarc Discharge in Electrolyte

Surface Analyses of High-Temperature Oxidated TiAl-Based Alloys

Non-Isothermal Oxidation Behavior and Mechanism of a High Temperature Near-α Titanium Alloy

Influence of Thermal Oxidation Temperature on the Microstructural and Tribological Behavior of Ti6Al4V Alloy

Microstructural evolution and high-temperature oxidation mechanisms of a titanium aluminide based alloy

Surface Bio-Modification by TiO2 Film on Biomedical Titanium Alloy

Microstructure Evolution and Oxidation Mechanism of Ta5 Titanium Alloy During High-Temperature Heat Treatment

Oxidation behavior and effect of oxidation on microstructure and tensile properties of Ti-5Al-5Mo-5V-1Cr-1Fe alloy

Thermal Stability of Titania Films Prepared on Titanium by Micro-Arc Oxidation

Study of Micro-arc Oxidation and Hydrothermal Treatment on the Surface of Pure Titanium

Influence of Thermal Oxidation Duration on the Microstructure and Fretting Wear Behavior of Ti6Al4V Alloy

High-temperature oxidation resistance of ceramic coatings on titanium alloy by micro-arc oxidation in aluminate solution

Non-isothermal Oxidation Characteristic of Titanium-Aluminium Intermetallic Alloys

The Effect of Surface Oxidation Behavior on the Fracture Toughness of Ti–5Al–5Mo–5V–1Cr–1Fe Titanium Alloy

Thermal Oxidation Behavior and Tribological Properties of Textured TC4 Surface: Influence of Thermal Oxidation Temperature and Time