Abstract:Hot pressing was used to produce compact ceramic samples with the following composition (wt.%): 60 ZrB2 + 20 SiC + 20 (Al2O3 + 32 t-ZrO2). The tetragonal modification of zirconium oxide in the eutectic was stabilized by yttrium oxide. The porosity of the samples was 3–5%. The mechanical properties of the ceramics (hardness HV, fracture toughness KIc, tensile strength δf, compressive strength Y, grain-boundary strength S, and bending strength σ) were studied. Analysis of the microstructure and elemental composition of the phases revealed that a defect-free structure developed in the ZrB2-based composite through strong Van Der Waals adhesive interaction at the SiC–Al2O3 interface, which increased the fracture toughness to 9.4 MPa ∙ m1/2. In turn, this increased the grain strength from 0.64 GPa for the basic composite to 3.46 GPa for the ZrB2–SiC composite with an oxide addition. An addition of Al2O3 + 32 wt.% t-ZrO2 was introduced in sufficient quantities not only to reduce the fracture stress but also to promote plastic deformation of the material for high-temperature bending strength. Study of the oxidation process showed that the weight increment of the 60 wt.% ZrB2 + 20 wt.% SiC + 20 wt.% (Al2O3 + 32 wt.% t-ZrO2) sample at 1600°C for a holding time of 1 h was stabilized by dense oxide scale formed on the material, while the weight increment of the ZrB2 + 20 wt.% SiC sample and, consequently, the scale thickness increased monotonically. The scale that formed on the ZrB2 + 20 wt.% SiC samples with an addition of Al2O3 + 32 wt.% t-ZrO2 consisted of an upper Al2SiO5-based layer 50 μm thick with ZrO2 inclusions and a lower ZrO2-based layer up to 80 μm thick with Al2SiO5 inclusions. The eutectic Al2O3 + 32 wt.% t-ZrO2 oxide addition to the basic ZrB2–SiC system had higher oxidation resistance and thus prevented the diffusion of oxygen into the material.

Microstructure and High-Temperature Mechanical Properties of Zro2-Al2o3-Sic Ceramics

Influence of Hot Pressing Temperature and SiC Content on the Microstructure and Mechanical Properties of ZrB2-SiC

Microstructure and Mechanical Properties of Hot-Pressed Al2O3–mullite–ZrO2–SiC Composites

Microstructure and Properties of Hot Pressed Zr2(Al(Si))4C5/SiC Composites

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Microstructural evolution and mechanical properties of ZrO<sub>2</sub> (3Y)-Al<sub>2</sub>O<sub>3</sub>-SiC(<sub>w</sub>) ceramics under oscillatory pressure sintering

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO2–Al2O3-SiCp ceramics

Optimization of microstructure and mechanical properties of oscillatory pressure sintered ZrO<sub>2</sub>-Al<sub>2</sub>O<sub>3</sub>-SiCp ceramics

Microstructure and Mechanical Properties of ZrB2-SiC Composites

Pressureless Sintering of Silicon Carbide Ceramics Containing Zirconium Diboride

Preparation, mechanical properties, and toughening mechanisms of SiCw/SiCp‐reinforced zirconia‐toughened alumina ceramics

Mechanical and Electrical Properties of MoSi2-based Ceramics with Various ZrB2-20 Vol% SiC As Additives for Ultra High Temperature Heating Element

Microstructure and mechanical properties of Zr3Al3C5-based ceramics synthesized by Al-Si melt infiltration

Mechanical Properties and Microstructure of Sic-Zro2(3y)-Al2o3 Nanocomposites

Microstructure and Mechanical Properties of Hot-Pressed ZrB2–SiC–ZrO2f Ceramics with Different Sintering Temperatures

Study on Zrc-20vol.%Sicw Ultrahigh Temperature Ceramics by Hot Pressing

Mechanical and Corrosion Properties of ZrB2–SiC Composite Ceramics with Oxide Additions

Study on the mechanical properties and microstructure of Al2O3/nano-SiC multiphase ceramics

Microstructure and mechanical properties of ZrB2–SiC nanocomposite ceramic

Novel TiC-based ceramic with enhanced mechanical properties by reaction hot-pressing at low temperature

Microstructural Evolution and Performance of Carbon Fiber-Toughened ZrB2 Ceramics with SiC or ZrSi2 Additive