Abstract:Copper-based wire is the key conductor material in integrated circuit bonding wire, high-end audio and video transmission line, medical wire harness and other fields. It is of significant interests to improving the strength and retaining their good electrical conductivity of copper-based wires for broad applications. The combination of heat treatment and deformation to control the microstructure is a promising method for this objective. In this paper, the Cu-3.5 wt. %Ag alloy rod with diameter of 16 mm was prepared by the hot mold horizontal continuous casting. We discussed the effects of solution + aging (S.A), solution + aging + cold drawing (S.A.C), solution + cold drawing + aging (S.C.A) on the distribution of Ag phase, dislocation morphology, strength and electrical conductivity of Cu-3.5 wt. %Ag alloy. The results show that continuing cold deformation after aging makes the strength of Cu-3.5 wt. %Ag alloy is up to 417.2 MPa, which is 84.6 % higher than that by S.A process. After S.A.C treatment, the dislocation density sharply increases, and the dislocation is arranged in a network structure. The dispersed nano-spherical Ag phase with an average size of 12 nm precipitation after aging strongly prevents dislocation slip. Moreover, the chain-like Ag phase effectively "intercepts" or "lock" the dislocations in the local area. The S.A.C process fully exerts the synergistic strengthening effect of aging precipitation strengthening and deformation strengthening induced by the interaction between nano-Ag phase and dislocation. This process is suitable for medical wiring harness, bonding wire and other application scenarios with higher strength requirements. On the other hand, if cold deformation is applied before aging, that is, S.C.A process. The electrical conductivity of Cu-3.5 wt. % Ag alloy reaches 95.5 % IACS, which is close to 100 % IACS of pure copper. The achievement of ultra-high conductivity is mainly attributed to the formation of a large number of band-shaped nano-Ag phase with an average length of 450 nm and width of 25 nm, and the arrangement direction remain consistent. In addition, the uniform distribution of dislocations is also beneficial to greatly improve the electrical conductivity. The S.C.A process is suitable for high-end audio and video transmission lines and other application scenarios that require higher electrical conductivity.

Critical current density improvement by intermediate deformation for the fabrication of Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ /Ag round wires

Improving Bi-2212 multi-filament wire quality and superconductivity by cryogenic drawing

Large critical current density improvement in Bi-2212 wires through groove-rolling process

High critical current density in low-cost iron-based superconducting round wires annealed at ambient pressure

Uniaxial Strain Induced Critical Current Degradation of Ag-Sheathed Bi-2212 Round Wire

Fabrication and study of thin Bi-2223 round wires

Improvement of plastic deformation property and current carrying capacity of Bi2212 wires through low oxygen partial pressure post-annealing of precursor

Relating Residual Stress and Microstructure to Mechanical and Giant Magneto-Impedance Properties in Cold-Drawn Co-based Amorphous Microwires

EFFECT OF HEAVILY DRAWING ON THE MICROSTRUCTURE AND PROPERTIES OF Cu-Cr ALLOYS

Investigation on Drawing Process of Bi-2223/Ag Wires Using Racetrack-Type Dies: Simulation and Experiments

Strain Compatibility Behavior in Cu-6%Ag Alloy During Drawing into Filamentary Structure

Role of internal gases and creep of Ag in controlling the critical current density of Ag-sheathed Bi2Sr2CaCu2Ox wires

Investigation on the Drawing Process of the Bi-2223/Ag Wire Based on the Physics of Inhomogeneous Inorganic Materials Method

Groove-rolling as an alternative process to fabricate Bi-2212 wires for practical applications

New concept for the development of Bi-2212 wires for high field applications

Microstructure and Critical Current Density of Bi-2212 Single- and Multi-filamentary Wires with Overpressure Heat Treatment Processing

Strain Strengthening Of Ag-10cu In Situ Filamentary Composite Prepared By Heavy Deformation

Mechanisms for high strength and ultra-high electrical conductivity of Cu-3.5wt.%Ag alloy prepared by thermomechanical treatment

Fabrication and Properties of Multifilamentary MgB2 Wires by In-Situ Powder-in-tube Process

Enhancement of the Critical Current Density of Ag-sheathed Bi-2223 Tapes by Optimized Pre-Annealing and Pre-Rolling Process

Microstructure evolution of high-strength and ultra-high-conductivity microfilament wire prepared by continuous deformation of single-crystal copper