Abstract:Bi-2212 is the only high-field, high-temperature superconductor (HTS) capable of reaching a critical current density $J_{\text{c}}$(16 T, 4.2 K) of 6500 $\mathrm{A\cdot mm^{-2}}$ in the highly desirable round wire (RW) form. However, state-of-the-art Bi-2212 conductors still have a critical current density ($J_{\text{c}}$) to depairing current density ($J_{\text{d}}$) ratio around 20 to 30 times lower than that of state-of-the-art $\mathrm{Nb-Ti}$ or REBCO. Previously, we have shown that recent improvements in Bi-2212 RW $J_{\text{c}}$ are due to improved connectivity associated with optimization of the heat treatment process, and most recently due to a transition to a finer and more uniform powder manufactured by Engi-Mat. One quantitative measure of connectivity may be the critical current ($I_{\text{c}}$) distribution, since the local $I_{\text{c}}$ in a wire can vary along the length due to variable vortex-microstructure interactions and to factors such as filament shape variations, grain-to-grain connectivity variations and blocking secondary phase distributions. Here we compare $\sim$ 0.1 m length $I_{\text{c}}$ distributions of Bi-2212 RWs with recent state-of-the-art very high-$J_{\text{c}}$ Engi-Mat powder and lower $J_{\text{c}}$ and older Nexans granulate powder. We do find that the $I_{\text{c}}$ spread for Bi-2212 wires is about twice the relative standard of high-$J_{\text{c}}$ $\mathrm{Nb-Ti}$ well below $H_{\text{irr}}$. We do not yet see any obvious contribution of the Bi-2212 anisotropy to the $I_{\text{c}}$ distribution and are rather encouraged that these Bi-2212 round wires show relative $I_{\text{c}}$ distributions not too far from high-$J_{\text{c}}$ $\mathrm{Nb-Ti}$ wires.

Fabrication and study of thin Bi-2223 round wires

Fabrication and Properties of Multifilamentary MgB2 Wires by In-Situ Powder-in-tube Process

Microstructure and Critical Current Density of Bi-2212 Single- and Multi-filamentary Wires with Overpressure Heat Treatment Processing

Critical current density improvement by intermediate deformation for the fabrication of Bi 2 Sr 2 Ca 2 Cu 3 O 10+δ /Ag round wires

Development of persistent joints for superconducting Bi-2212 coils

Critical Current Distributions of Recent Bi-2212 Round Wires

New concept for the development of Bi-2212 wires for high field applications

Fabrication of Bi-2223 Superconducting Thick Films Via A Non-Vacuum Method on Silver Foil Substrates

Performance and Microstructure of Bi-2212 Wire under Different OverPressures Heat-treatment

Investigation on Drawing Process of Bi-2223/Ag Wires Using Racetrack-Type Dies: Simulation and Experiments

Improving Bi-2212 multi-filament wire quality and superconductivity by cryogenic drawing

Fabrication and Electromagnetic Characterization of Ultrasmall Diameter REBCO Wires

Large critical current density improvement in Bi-2212 wires through groove-rolling process

Critical current of Bi-2212 round wires with different heat treatment conditions

Uniaxial Strain Induced Critical Current Degradation of Ag-Sheathed Bi-2212 Round Wire

Axial Tensile Stress-Strain Characterization Of Bi-2212 Round Wire With Different Heat Treatments

Groove-rolling as an alternative process to fabricate Bi-2212 wires for practical applications

Fabrication and Characterization of Melt-Extracted Co-Based Amorphous Wires

Influence of Torsional Strain on the Bi-2212 Tapes and Round Wires under Background Field

High critical current density in low-cost iron-based superconducting round wires annealed at ambient pressure

Stress–Strain Distribution Analysis in Bi2212 Subcable Based on Numerical Modeling and Experiment