Abstract:We demonstrate a method for the preparation of fully solution processed inorganic solar cells from a spin and spray coating deposition of nanocrystal inks. For the photoactive absorber layer, colloidal CdTe and CdSe nanocrystals (3-5 nm) are synthesized using an inert hot injection technique and cleaned with precipitations to remove excess starting reagents. Similarly, gold nanocrystals (3-5 nm) are synthesized under ambient conditions and dissolved in organic solvents. In addition, precursor solutions for transparent conductive indium tin oxide (ITO) films are prepared from solutions of indium and tin salts paired with a reactive oxidizer. Layer-by-layer, these solutions are deposited onto a glass substrate following annealing (200-400 °C) to build the nanocrystal solar cell (glass/ITO/CdSe/CdTe/Au). Pre-annealing ligand exchange is required for CdSe and CdTe nanocrystals where films are dipped in NH4Cl:methanol to replace long-chain native ligands with small inorganic Cl(-) anions. NH4Cl(s) was found to act as a catalyst for the sintering reaction (as a non-toxic alternative to the conventional CdCl2(s) treatment) leading to grain growth (136±39 nm) during heating. The thickness and roughness of the prepared films are characterized with SEM and optical profilometry. FTIR is used to determine the degree of ligand exchange prior to sintering, and XRD is used to verify the crystallinity and phase of each material. UV/Vis spectra show high visible light transmission through the ITO layer and a red shift in the absorbance of the cadmium chalcogenide nanocrystals after thermal annealing. Current-voltage curves of completed devices are measured under simulated one sun illumination. Small differences in deposition techniques and reagents employed during ligand exchange have been shown to have a profound influence on the device properties. Here, we examine the effects of chemical (sintering and ligand exchange agents) and physical treatments (solution concentration, spray-pressure, annealing time and annealing temperature) on photovoltaic device performance.

Silicon and Germanium Nanocrystal Inks for Low-Cost Solar Cells

Silicon Rich Carbide As A Conductive Substrate For Si Qd Solar Cells

Application of Silicon Nanocrystals in Solar Cells

Enhancing The Efficiency Of Multicrystalline Silicon Solar Cells By The Inkjet Printing Of Silicon-Quantum-Dot Ink

Printable Nanostructured Silicon Solar Cells for High-Performance, Large-Area Flexible Photovoltaics

Advanced PECVD Processes for SiNW Based Solar Cells and Thin Film Transistors

Low Reflectance Gaas Nano-Cones Fabricated By Colloidal Lithography For Solar Cells

Silicon nanocrystals synthesized using very high frequency non-thermal plasma and their application in photovoltaics

Microcrystalline silicon carbide window layers in thin film silicon solar cells

Plasma Synthesis of Silicon Nanocrystals: Application to Organic/Inorganic Photovoltaics Through Solution Processing

Building Solar Cells From Nanocrystal Inks

Germanium-doped Crystal Silicon for Solar Cells

Inexpensive Transparent Nanoelectrode for Crystalline Silicon Solar Cells

Production Of Low-Cost Silicon Films Via Molten Salt Electrodeposition

Electrodeposition of Crystalline Silicon Films from Silicon Dioxide for Low-Cost Photovoltaic Applications

Electrodeposition of Photoactive Silicon Films for Low-Cost Solar Cells

Environmentally Friendly AgBiS2 Nanocrystal Inks for Efficient Solar Cells Employing Green Solvent Processing

The use of porous silicon layers in thin‐film silicon solar cells

Three novel ways of making thin-film crystalline-silicon layers on glass for solar cell applications

Fabrication of Fully Solution Processed Inorganic Nanocrystal Photovoltaic Devices

A Polymer/Carbon‐Nanotube Ink as a Boron‐Dopant/Inorganic‐Passivation Free Carrier Selective Contact for Silicon Solar Cells with over 21% Efficiency