Analysis of Scale Factor Error for Open-loop Fiber Optic Gyroscope with A Digital Signal Processing System

Zhongwei Tan,Chuanchuan Yang,Ziyu Wang

DOI: https://doi.org/10.1364/acp.2013.af2i.23

2013-01-01

Abstract:We research the effect of the instability of the modulation depth and the nonlinearity of the modulating signal on the scale factor error for open-loop fiber optic gyroscope with a digital signal processing system.

What problem does this paper attempt to address?

Scale Factor Calibration and Dynamic Angle Measurement Method Based on Self-Collimator and Fiber Optic Gyroscope

Jiapeng Mou,Tengchao Huang,Guangyao Ying,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2019.101945

IF: 2.8

2019-01-01

Optical Fiber Technology

Abstract:The scale factor, which the output of the fiber optic gyroscope (FOG) is proportional to, is sensitive to many factors in engineering. When the scale factor fluctuates during the measurement process, it will bring an error to the angle measurement results if the scale factor is not calibrated in time. A scale factor real-time calibration and angle measurement scheme based on self-collimator is proposed to eliminate the error caused by the fluctuation of the scale factor. The experimental results show that the error between the FOG and the rotary table is decreased to nearly 1 '' after adopting the scheme at low angular velocities. Although the error is become larger when the angular velocity is increasing, the angle measurement results can still has a good stability.
Method to Suppress Scale Factor Error for All-Digital Signal Processing Open-loop Fiber-optic Gyroscope

Zhongwei Tan,Chuanchuan Yang,Ziyu Wang

DOI: https://doi.org/10.1364/acpc.2014.ath1i.6

2014-01-01

Abstract:This paper proposes a method to suppress the scale factor error caused by the nonlinearity of the modulating signal in the all-digital signal processing open-loop fiber-optic gyroscope.
Digital System Study Applied to Performance Detection of Optic Fiber Gyroscope

朱辉,张登伟,牟旭东,舒晓武,刘承

DOI: https://doi.org/10.3969/j.issn.1005-5630.2004.05.004

2004-01-01

Abstract:This paper introduces the evaluation system of open loop signal of fiber optic gyroscope.We give the signal got from gyroscope by Lock_-in Amplifier to PC,design friend interface between human and PC,and evaluate the capability of FOG by bias,bias stability,scale factor and so on.PC and SR830 adopt USB and GPIB interface,thus we can control the real time course by the digital sampling and processing system designed by VC++ on windows,high speed receiving and sending data and display the result by picture and words.Then we increase the stability of system,and reduce the error rate,and the standardization of detection system is realized.
Research on digital signal detection method in closed loop fiber gyros

Wei Ye,Yongfeng Ni,Weidang Zhao,Xiaowu Shu,Kejiang Zhou,Guoguang Yang

1998-01-01

Abstract:The all digital signal detection system based on the digital phase ramp modulation technology in closed-loop fiber optic gyros (FOGs) is developed. The measurement mothod of several important parmeters and the rerults are presented.
General comments on signal processing scheme for fiber optic gyroscope

Xuhan Dai,Kejiang Zhou,Cheng Liu,Xiaowu Shu,Jun Ding,Guoguang Yang

1999-01-01

Abstract:With consideration on application, it is presented typical closed-loop and open-loop FOG signal processing scheme used for different application and fulfilled different requirements. Both advantages and disadvantages of each scheme are compared. Fiber optic gyroscope is one of the most prominent components utilized in intertial navigation system in recent years. The signal-processing scheme is the key factor for the improvement of its performances.
Analysis of Fiber Optic Gyroscope Dynamic Error Based on CEEMDAN

Shuai Zhao,Yilan Zhou,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2022.102835

IF: 2.8

2022-01-01

Optical Fiber Technology

Abstract:The fiber optic gyroscope (FOG) is an angular rate sensor based on Sagnac effect. It has been widely used in aviation, unmanned, robot, and other fields due to its benefits of all solid state, high precision, and low cost. However, the photoelectric devices inside the FOG will produce a non-negligible error in the dynamic environment, resulting in zero bias drift and increased noise. Currently, research on the dynamic error of FOG focuses primarily on linear vibration, assuming that no input angular rate exists at this moment. However, the dynamic errors caused by angular vibration are more complicated in the practical application environment. The output of FOG includes both effective angular information and dynamic error at this moment, which means that the dynamic error should be removed while the effective angular information must be retained. In this paper, we focus on the effect of angular vibration on FOG, and propose a dynamic error compensation method of FOG based on complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN) that properly separates the effective signal and dynamic error. We also consider the amplitude frequency characteristics of FOG under dynamic conditions and utilize the FOG bandwidth test experiment to verify the effectiveness of our method. The experimental results show that the compensated signal can correctly calculate the bandwidth of FOG. It indicates that our method can effectively compensate the dynamic error in angular vibration environment while improving the performance of FOG in dynamic environment.
Visualization Study on Performance Digital Evaluation System for Optic Fiber Gyroscope

Xiaowu Shu

2002-01-01

Abstract:A digital evaluation system that receives and processes optic fiber gyroscope signal is developed. It evaluates performances of optic fiber gyroscope through calculating zero drift, zero deviation repeatability and scale factor, etc. With a digital sampling and processing system designed by VC++, the real time controlling procedure, high-speed receiving and sending data can be carried out under Windows platform, and the results can be displayed by graphics and words visualization. The transmission error is reduced through introduction of frame structure, thus the reliability of the system will be improved and error rate will be reduced simultaneously.
Uncertainty Analysis of Dynamic Goniometer Based on Fiber Optic Gyroscope

Jiapeng Mou,Bin Pang,Guangyao Ying,Fanyan Xue,Tengchao Huang,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1117/12.2509290

2019-01-01

Abstract:The basic principle of a dynamic goniometer based on fiber optic gyroscope was introduced. According to this principle, the model on uncertainty of angle measurement results was established and the simulation analysis on uncertainty of measurement results was performed. Furthermore, a series of repetitive experiments with this goniometer at different rotational velocities were carried out. Experiments results showed that they were consistent with the uncertainty got from the theoretical analysis when the confidence level was set to 95% and the evaluation model on uncertainty was effective.
Research on Dynamic Performance Evaluation of Fiber Optic Gyroscope Based on Laser Doppler Measurement Technology

Shuai Zhao,Yilan Zhou,Xiaowu Shu

DOI: https://doi.org/10.1117/12.2607026

2021-01-01

Abstract:The bandwidth of the fiber optic gyroscope is an important indicator of its frequency characteristics. When the environmental conditions is under high dynamic such as vibration and sharp turns, the measurement accuracy of fiber optic gyroscope is greatly affected due to the limitation of the frequency characteristics of fiber optic gyroscopes. And the traditional bandwidth measurement method is to record the angular vibration's amplitude and frequency of the turntable and the output of fiber optic gyroscope, and then use the least squares method to obtain the bandwidth of fiber optic gyroscope. However, the output frequency of the turntable's circular grating encoder is not high enough, usually less than 100Hz, which cannot reflect the more comprehensive dynamic performance of the fiber optic gyroscope. And the manual operation test is always cumbersome. All of these limits the further research on the dynamic performance of fiber optic gyroscope. Therefore, this paper proposes a fiber optic gyroscope bandwidth evaluation method based on laser Doppler measurement technology. Then, an adaptive modal decomposition algorithm is proposed, which can adaptively decompose complex nonlinear and non-stationary signals into multiple frequency components. Our system can realize high-frequency, high-precision and non-contact, which is of great significance to the research of the dynamic performance of the fiber optic gyroscope.
Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

Jiapeng Mou,Tengchao Huang,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2020.102368

IF: 2.8

2020-01-01

Optical Fiber Technology

Abstract:The fiber optic gyroscope (FOG) has been widely used in the field of dynamic angle measurement due to its characteristics of wide dynamic range and high precision. Considering the change of the installation state of the FOG and the inconvenience of the calibration of the scale factor in engineering, an error compensation of the angle measurement using FOG, which is based on the tilt sensor, is proposed in this paper. Firstly, the principle of the angle measurement based on the FOG and the principle of the tilt sensor are introduced and the error compensation model based on tilt sensor is established. Secondly, simulation analysis and error analysis are performed and the compensation scheme is designed. Finally, according to the compensation scheme, the instrument prototype is built and the experiments are carried out. The experimental results show that although the error is not completely eliminated after adopting compensation scheme, the angle measurement deviation of the FOG can be greatly reduced and limited within 5 '' when the tilt state changes within a small range (the output of the tilt sensor is less than 0.3 degrees). It indicates that the compensation scheme is effective and feasible. More importantly, it is easier to realize in engineering in contrast with other compensation methods.
Compensation of Scale Factor Error for Open-loop Fiber Optic Gyroscopes

Lanxin Zhu,Huimin Huang,Xinyu Cao,Yanjun Chen,Zhengbin Li

DOI: https://doi.org/10.1364/cleo_at.2024.jth2a.160

2024-01-01

Abstract:Theoretical analysis of the scale factor nonlinearity (SFN) in open-loop fiber optic gyroscopes is conducted. A k-factor compensation method is introduced, effectively reducing SFN to 2.5 ppm over the range of -300 to +300°/s.
Study on Temperature Stability of Scale-Factor in Closed-Loop Fiber Optical Gyroscope

Yan-ji WU,Xian-lin HUANG

DOI: https://doi.org/10.3969/j.issn.1001-0645.2007.07.013

2007-01-01

Abstract:Based on closed-loop fiber optical gyroscopes, research work on the temperature stability of the scale-factor has been performed. The mathematical expression of the scale-factor has been established. The mechanism of temperature influence on the stability of scale-factor was analyzed. The coefficient of some parameters was given. An experiment on the temperature stability of the scale-factor has been performed in closed-loop fiber optical gyroscopes. It can be seen from the experimental results that the temperature sensitivity of the scale-factor has been changed from 8.08 × 10-4/°C to 1.70 × 10-5/°C.
Research on Scale Factor of Closed-Loop Depolarized Fiber Gyroscope

ZHOU Ke-jiang,LIU Shu-jun

DOI: https://doi.org/10.3969/j.issn.1001-5078.2013.03.013

2013-01-01

Abstract:The nonlinear error of scale factor of depolarized fiber gyroscope(D-FOG)with closed-loop has been investigated theoretically and experimentally for the first time.Our results show that the nonlinear error of depolarized FOG with standard single-mode fiber coil,which is larger than that of polarization-maintaining FOG,is caused by the different modulated depths of serrodyne for the two states of polarization.Practical methods to reduce nonlinear error of depolarized FOG are suggested in this paper.
Improving the Scale Factor Thermal Stability of Resonant Fiber-Optic Gyroscopes by Tracking the Half-Wave Voltage of the Phase Modulator

Lu Liu,Shuang Liu,Hewei Wang,Junyi Hu,Binjie Li,Huilian Ma

DOI: https://doi.org/10.1109/jlt.2024.3467163

IF: 4.7

2024-01-01

Journal of Lightwave Technology

Abstract:In this paper, a novel method for detecting and tracking the half-wave voltage of the phase modulator in a resonant fiber-optic gyroscope (RFOG) is proposed and demonstrated. A theoretical model is first developed to illustrate the effect of phase modulator half-wave voltage fluctuations on the stability of the RFOG scale factor. A novel method for detecting the half-wave voltage fluctuations is then proposed by applying an additional sawtooth modulation signal. Based on this, a double closed-loop RFOG system scheme employing a half-wave voltage servo loop is designed to simultaneously eliminate the sawtooth wave reset voltage error during the RFOG operation. The performance of the RFOG was tested under variable temperature conditions. The experimental results indicated that the reset voltage errors could be controlled within 1 mV, and the scale factor thermal stability was improved from 95.97 ppm/°C to 9.39 ppm/°C.
Study on Nonlinear Error Calibration of Fiber Optical Gyroscope Scale Factor Based on LSTM

Shuai Zhao,Yilan Zhou,Xiaowu Shu

DOI: https://doi.org/10.1016/j.measurement.2022.110783

IF: 5.6

2022-01-01

Measurement

Abstract:The calibration accuracy of the inertial navigation system (INS) has a non-negligible effect on its actual navigation performance. As the core component of the INS, the scale factor error of the fiber optical gyroscope (FOG) is one of the main error sources of the INS, which has a vital impact on the navigation accuracy. Generally, the scale factor of FOG is considered to be a constant value, but with the increasing demand for the accuracy of FOG, the scale factor error can not be ignored, how to calibration the FOG scale factor at different input velocity rates and temperature has attracted people's attention. The traditional calibration methods usually select several fixed temperature points and input velocity points, then the scale factor error is compensated by linear fitting or piecewise fitting. In order to improve the calibration accuracy, our paper considers the coupling effect of input velocity rate and temperature and designs a calibration experiment at continuous input velocity rates and temperature, the calibration time is shortened by 30%, then we propose a nonlinear error compensation method based on the LSTM. The experimental result shows that the std error of the FOG scale factor is reduced from 280 ppm to 13 ppm and the angle measurement error is reduced by 70%, which verify the effectiveness of our method.
Analysis of Serrodyne′s Reset Amplitude Errors in Resonator Fiber Optic Gyroscopes by Digital Modulation

李如春,马慧莲,金仲和,王跃林

DOI: https://doi.org/10.3321/j.issn:0258-7025.2004.09.019

2004-01-01

Chinese Journal of Lasers

Abstract:Resonator fiber optical gyroscope (R-FOG) uses ring resonator to enhance the Sagnac effect, the detecting methods have open-loop and closed-loop, the phase modulator′s controlling signal has analogous and digital in circuit. Compared with analogous modulation, the method of digital closed-loop detection has a big dynamic range and high sensitivity. In resonator fiber optic gyroscopes by digital modulation, imperfect serrodyne′s reset amplitude V_ 2π has influence on the rotation sensing errors and the scale factor non-linearity. The effects of imperfect V_ 2π on the system are analyzed theoretically. If the amplitude is not exactly V_ 2π, two electric fields, E_ cross and E_ bar cannot result in optimum destructive interference, thus the resulting waveform has errors. Based on the sum of electric fields expression in detector, numerical calculations of rotation sensing errors associated with imperfect serrodyne amplitude are given for resonator fiber optical gyro using two frequencies modulation. At last, some solutions for substantially reducing errors are presented.
Modulation Spectrum Analysis and Optimization for Closed-Loop RFOG under Dynamic Condition

Diqing Ying,Tao Xie,Zeyu Wang,Qiang Liu,Zhonghe Jin

DOI: https://doi.org/10.1016/j.optcom.2020.125659

IF: 2.4

2020-01-01

Optics Communications

Abstract:In this paper, the spectrum characteristics of the closed-loop RFOG, modulated by the digital sine and bipolar serrodyne wave, is analyzed under the dynamic condition. It is verified that the serious spectrum overlapping between the CCW and CW loops would be induced within a certain rotation rate range, which would increase the backscatter noise. Experimental tests indicate that the serious spectrum overlapping could more than double the standard deviation of gyro output signal, which badly deteriorates the gyro’s performance. According to the spectrum characteristics analysis result, to reduce the spectrum overlapping induced backscatter noise under the dynamic condition, a noise suppressing algorithm is proposed. This algorithm is realized by switching the initial reset frequency of the bipolar serrodyne wave at a crucial rotation rate to keep an enough frequency difference between the two modulation spectrums’ main harmonic components. Experimental test shows that when this algorithm is used, the decreased ratio of the standard deviation for gyro output signal can reach to about 70.5% at the rotation rates corresponding to the serious spectrum overlapping.
Performance Analysis of an Optical Passive Ring-Resonator Gyro with A Hollow-Core Photonic Bandgap Fiber Sensing Coil

X. L. Zhang,W. Jin,D. Q. Ying

DOI: https://doi.org/10.1117/12.869627

2010-01-01

Abstract:We evaluate the measurement errors induced by various deleterious effects in an optical passive ring-resonator gyro (OPRG) with a hollow-core photonic bandgap fiber (HC-PBF) sensing coil. The uncertainties in measuring rotation rate due to Kerr, Shupe, and Faraday effects are found to be reduced respectively by 2~3, 1, and 1~2 orders of magnitude as compared with an OPRG with a conventional single mode fiber (SMF) sensing coil of similar parameters. The errors due to shot and coherent backscatter noises are larger for the OPRG made of the current state-of-the-art HC-PBF than for the OPRG with a conventional SMF coil, but are expected to reduce in future with improved fiber manufacture technologies.
A Novel Digital Signal Processing System for Open-Loop Fiber Optic Gyroscope

Qin Wang,Chuanchuan Yang,Ziyu Wang

DOI: https://doi.org/10.1364/acpc.2012.af4b.5

2012-01-01

Abstract:A novel all digital signal processing system for open-loop fiber optic gyroscope is proposed. The effect of the fluctuation of laser power and the variation of modulation depth is eliminated in this proposed system.
A phase modulation method for improving the scale factor stability of Fiber-Optic Gyroscope

Shitong Chen,Jianhua Cheng,Wei Gao

DOI: https://doi.org/10.1109/ICMA.2008.4798722

2008-01-01

Abstract:The usual scheme of fiber-optic gyroscope(FOG) is digital single closed-loop, but the scale factor stability is affected by the variation of half-wave voltage of LiNbO3 integrated optic phase modulator. The half-wave voltage changes with the variation of the integrated optic phase modulator performance dependence on temperature and the bias voltage applied to the phase modulator. In order to improve the scale factor stability, double closed-loop scheme FOG with square wave biasbias modulation is used to compensate the the variation of half-wave voltage, but it is inefficient at low rates. The double closed-loop scheme FOG with ldquofour-bias-staterdquo bias modulation is used to improve the compensation efficiency and SNR, and the bias modulation equations are presented here. The scale factor stability of the new scheme is improved about by one time than the usual scheme.

Analysis of Scale Factor Error for Open-loop Fiber Optic Gyroscope with A Digital Signal Processing System

Scale Factor Calibration and Dynamic Angle Measurement Method Based on Self-Collimator and Fiber Optic Gyroscope

Method to Suppress Scale Factor Error for All-Digital Signal Processing Open-loop Fiber-optic Gyroscope

Digital System Study Applied to Performance Detection of Optic Fiber Gyroscope

Research on digital signal detection method in closed loop fiber gyros

General comments on signal processing scheme for fiber optic gyroscope

Analysis of Fiber Optic Gyroscope Dynamic Error Based on CEEMDAN

Visualization Study on Performance Digital Evaluation System for Optic Fiber Gyroscope

Uncertainty Analysis of Dynamic Goniometer Based on Fiber Optic Gyroscope

Research on Dynamic Performance Evaluation of Fiber Optic Gyroscope Based on Laser Doppler Measurement Technology

Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

Compensation of Scale Factor Error for Open-loop Fiber Optic Gyroscopes

Study on Temperature Stability of Scale-Factor in Closed-Loop Fiber Optical Gyroscope

Research on Scale Factor of Closed-Loop Depolarized Fiber Gyroscope

Improving the Scale Factor Thermal Stability of Resonant Fiber-Optic Gyroscopes by Tracking the Half-Wave Voltage of the Phase Modulator

Study on Nonlinear Error Calibration of Fiber Optical Gyroscope Scale Factor Based on LSTM

Analysis of Serrodyne′s Reset Amplitude Errors in Resonator Fiber Optic Gyroscopes by Digital Modulation

Modulation Spectrum Analysis and Optimization for Closed-Loop RFOG under Dynamic Condition

Performance Analysis of an Optical Passive Ring-Resonator Gyro with A Hollow-Core Photonic Bandgap Fiber Sensing Coil

A Novel Digital Signal Processing System for Open-Loop Fiber Optic Gyroscope

A phase modulation method for improving the scale factor stability of Fiber-Optic Gyroscope