Compensation of Scale Factor Error for Open-loop Fiber Optic Gyroscopes

Lanxin Zhu,Huimin Huang,Xinyu Cao,Yanjun Chen,Zhengbin Li

DOI: https://doi.org/10.1364/cleo_at.2024.jth2a.160

2024-01-01

Abstract:Theoretical analysis of the scale factor nonlinearity (SFN) in open-loop fiber optic gyroscopes is conducted. A k-factor compensation method is introduced, effectively reducing SFN to 2.5 ppm over the range of -300 to +300°/s.

What problem does this paper attempt to address?

Scale Factor Calibration and Dynamic Angle Measurement Method Based on Self-Collimator and Fiber Optic Gyroscope

Jiapeng Mou,Tengchao Huang,Guangyao Ying,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2019.101945

IF: 2.8

2019-01-01

Optical Fiber Technology

Abstract:The scale factor, which the output of the fiber optic gyroscope (FOG) is proportional to, is sensitive to many factors in engineering. When the scale factor fluctuates during the measurement process, it will bring an error to the angle measurement results if the scale factor is not calibrated in time. A scale factor real-time calibration and angle measurement scheme based on self-collimator is proposed to eliminate the error caused by the fluctuation of the scale factor. The experimental results show that the error between the FOG and the rotary table is decreased to nearly 1 '' after adopting the scheme at low angular velocities. Although the error is become larger when the angular velocity is increasing, the angle measurement results can still has a good stability.
Compensation of Scale Factor Nonlinear Error Introduced by Harmonic Distortion for Open-Loop Fiber Optic Gyroscopes.

L. A. N. X. I. N. Zhu,Y. U. W. E. N. Cao,H. U. I. M. I. N. Huang,Y. A. N. J. U. N. Chen,W. E. N. B. O. Wang,X. I. A. N. G. D. O. N. G. Ma,Z. H. E. N. G. B. I. N. LI

DOI: https://doi.org/10.1364/ol.483911

IF: 3.6

2023-01-01

Optics Letters

Abstract:The scale factor (SF) of a gyroscope is the ratio of the detection output rotational rate and the input, and is expected to be a constant. However, for open-loop interferometric fiber optic gyroscopes (IFOGs) with sinusoidal modulation, harmonic amplitudes are inevitably affected by detection defects, such as nonuniform frequency response of the photodetector or unequal gain of amplification circuits. As a result, harmonic distortion leads to SF nonlinearity, which seriously hinders the accuracy of high-precision gyroscopes. In this Letter, the theoretical form of the SF error introduced by harmonic distortion of open-loop gyroscopes is analyzed, and an effective and simple compensation method is proposed. Instead of traversing the whole dynamic range, the proposed method simplifies the calibration pretest, where only a section of the dynamic range needs to be tested. Experimental results on an open-loop IFOG prototype show that, with our proposed method, the SF nonlinear error is suppressed to 2.5 ppm within the range -300 to +300∘/s, which is 33 times less than that before compensation.
Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

Jiapeng Mou,Tengchao Huang,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2020.102368

IF: 2.8

2020-01-01

Optical Fiber Technology

Abstract:The fiber optic gyroscope (FOG) has been widely used in the field of dynamic angle measurement due to its characteristics of wide dynamic range and high precision. Considering the change of the installation state of the FOG and the inconvenience of the calibration of the scale factor in engineering, an error compensation of the angle measurement using FOG, which is based on the tilt sensor, is proposed in this paper. Firstly, the principle of the angle measurement based on the FOG and the principle of the tilt sensor are introduced and the error compensation model based on tilt sensor is established. Secondly, simulation analysis and error analysis are performed and the compensation scheme is designed. Finally, according to the compensation scheme, the instrument prototype is built and the experiments are carried out. The experimental results show that although the error is not completely eliminated after adopting compensation scheme, the angle measurement deviation of the FOG can be greatly reduced and limited within 5 '' when the tilt state changes within a small range (the output of the tilt sensor is less than 0.3 degrees). It indicates that the compensation scheme is effective and feasible. More importantly, it is easier to realize in engineering in contrast with other compensation methods.
One-Dimensional Angle Measurement Error Calibration Technique for Fiber Optic Gyroscope

Meng-fang YANG,Lei CHEN,Hui TIAN,Deng-wei ZHANG,Xiao-wu SHU,Shuang-liang CHE

DOI: https://doi.org/10.3969/j.issn.1009-086x.2017.04.003

2017-01-01

Abstract:As the angle measuring error of fiber optic gyroscope increases cumulatively under the condition of long-term operation,a new error calibration method is proposed for fiber optic sensor.The method is based on the principle of optical triangulation distance measurement,using data acquired by two laser displacement sensors to realize the real-time angular measurement,and the experimental verification of the measurement system is carried out on the high-precision turntable.Experimental results show that the range of angle measurement can be up to ± 10°,while the error is about ±0.005° through compensating the error by least square fitting method,which provides the basis for exact estimate of angle measuring precision of gyro.The non-contact optical measurement method used has no damage to the sur face to be measured.
Theory and Compensation Method of Axial Magnetic Error Induced by Axial Magnetic Field in A Polarization-Maintaining Fiber Optic Gyro

Yanru Zhou,Yuxiang Zhao,Hui Tian,Dengwei Zhang,Tengchao Huang,Lijun Miao,Xiaowu Shu,Shuangliang Che,Cheng Liu

DOI: https://doi.org/10.1117/1.oe.55.12.126106

IF: 1.3

2016-01-01

Optical Engineering

Abstract:In an axial magnetic field (AMF), which is vertical to the plane of the fiber coil, a polarization-maintaining fiber optic gyro (PM-FOG) appears as an axial magnetic error. This error is linearly related to the intensity of an AMF, the radius of the fiber coil, and the light wavelength, and also influenced by the distribution of fiber twist. When a PM-FOG is manufactured completely, this error only appears a linear correlation with the AMF. A real-time compensation model is established to eliminate the error, and the experimental results show that the axial magnetic error of the PM-FOG is decreased from 5.83 to 0.09 deg/h in 12G AMF with 18-dB suppression. (C) 2016 Society of Photo-Optical Instrumentation Engineers (SPIE)
Study on FOG Scale Factor Error Calibration in Start-Up Stage Based on GWO-GRU

Fei Wang,Shuai Zhao,Lei Wang,Yilan Zhou,Tengchao Huang,Xiaowu Shu

DOI: https://doi.org/10.1016/j.measurement.2022.112214

IF: 5.6

2022-01-01

Measurement

Abstract:The fiber optic gyroscope (FOG) is the core component of the inertial system, which has been widely utilized in aviation, maritime, automotive, and other fields. The scale factor is one of the critical parameters to characterize the dynamic performance of the FOG. Due to the temperature sensitivity of the optoelectronic devices, the scale factor errors will be caused with the temperature change. The traditional compensation method usually compensates the output of the FOG in a stable working state. Without considering the difference between the characteristics of the FOG in the start-up stage and the stable working state, the compensation accuracy of the traditional method cannot meet the demand for quick start-up in application areas. According to the above analysis, a novel scale factor error compensation method based on the grey wolf optimization (GWO) and gated recurrent unit (GRU) neural network is proposed in this paper. Furthermore, a new experiment is designed to calibrate the scale factor error in the start-up stage, which can reduce the calibration time and ensure the calibration accuracy. The experimental results demonstrate the proposed method significantly improves the compensation accuracy compared with other methods, such as the multilayer perceptrons (MLPs) and the traditional GRU network.
Study on Nonlinear Error Calibration of Fiber Optical Gyroscope Scale Factor Based on LSTM

Shuai Zhao,Yilan Zhou,Xiaowu Shu

DOI: https://doi.org/10.1016/j.measurement.2022.110783

IF: 5.6

2022-01-01

Measurement

Abstract:The calibration accuracy of the inertial navigation system (INS) has a non-negligible effect on its actual navigation performance. As the core component of the INS, the scale factor error of the fiber optical gyroscope (FOG) is one of the main error sources of the INS, which has a vital impact on the navigation accuracy. Generally, the scale factor of FOG is considered to be a constant value, but with the increasing demand for the accuracy of FOG, the scale factor error can not be ignored, how to calibration the FOG scale factor at different input velocity rates and temperature has attracted people's attention. The traditional calibration methods usually select several fixed temperature points and input velocity points, then the scale factor error is compensated by linear fitting or piecewise fitting. In order to improve the calibration accuracy, our paper considers the coupling effect of input velocity rate and temperature and designs a calibration experiment at continuous input velocity rates and temperature, the calibration time is shortened by 30%, then we propose a nonlinear error compensation method based on the LSTM. The experimental result shows that the std error of the FOG scale factor is reduced from 280 ppm to 13 ppm and the angle measurement error is reduced by 70%, which verify the effectiveness of our method.
Performance Analysis of an Optical Passive Ring-Resonator Gyro with A Hollow-Core Photonic Bandgap Fiber Sensing Coil

X. L. Zhang,W. Jin,D. Q. Ying

DOI: https://doi.org/10.1117/12.869627

2010-01-01

Abstract:We evaluate the measurement errors induced by various deleterious effects in an optical passive ring-resonator gyro (OPRG) with a hollow-core photonic bandgap fiber (HC-PBF) sensing coil. The uncertainties in measuring rotation rate due to Kerr, Shupe, and Faraday effects are found to be reduced respectively by 2~3, 1, and 1~2 orders of magnitude as compared with an OPRG with a conventional single mode fiber (SMF) sensing coil of similar parameters. The errors due to shot and coherent backscatter noises are larger for the OPRG made of the current state-of-the-art HC-PBF than for the OPRG with a conventional SMF coil, but are expected to reduce in future with improved fiber manufacture technologies.
Principle and Application of High Dynamic Fiber Gyroscope

Lei WANG,Xing-fan CHEN,Cheng LIU,Xiao-wu SHU

DOI: https://doi.org/10.3969/j.issn.1009-086x.2017.06.001

2017-01-01

Abstract:A method for designing a high dynamic fiber optic gyroscope (FOG) is presented for a class of high spinning carrier with demand of accuracy and range.It is fulfilled by identification of fringes to detect phase error beyond[-π,+ π] with the dynamic range over 40 000 (°)/s,which provides a new simple,effective and high reliability scheme for light of sight (LOS) stabilization and attitude control of navigation systems.
Method to Suppress Scale Factor Error for All-Digital Signal Processing Open-loop Fiber-optic Gyroscope

Zhongwei Tan,Chuanchuan Yang,Ziyu Wang

DOI: https://doi.org/10.1364/acpc.2014.ath1i.6

2014-01-01

Abstract:This paper proposes a method to suppress the scale factor error caused by the nonlinearity of the modulating signal in the all-digital signal processing open-loop fiber-optic gyroscope.
Uncertainty Analysis of Dynamic Goniometer Based on Fiber Optic Gyroscope

Jiapeng Mou,Bin Pang,Guangyao Ying,Fanyan Xue,Tengchao Huang,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1117/12.2509290

2019-01-01

Abstract:The basic principle of a dynamic goniometer based on fiber optic gyroscope was introduced. According to this principle, the model on uncertainty of angle measurement results was established and the simulation analysis on uncertainty of measurement results was performed. Furthermore, a series of repetitive experiments with this goniometer at different rotational velocities were carried out. Experiments results showed that they were consistent with the uncertainty got from the theoretical analysis when the confidence level was set to 95% and the evaluation model on uncertainty was effective.
Analysis of Fiber Optic Gyroscope Dynamic Error Based on CEEMDAN

Shuai Zhao,Yilan Zhou,Xiaowu Shu

DOI: https://doi.org/10.1016/j.yofte.2022.102835

IF: 2.8

2022-01-01

Optical Fiber Technology

Abstract:The fiber optic gyroscope (FOG) is an angular rate sensor based on Sagnac effect. It has been widely used in aviation, unmanned, robot, and other fields due to its benefits of all solid state, high precision, and low cost. However, the photoelectric devices inside the FOG will produce a non-negligible error in the dynamic environment, resulting in zero bias drift and increased noise. Currently, research on the dynamic error of FOG focuses primarily on linear vibration, assuming that no input angular rate exists at this moment. However, the dynamic errors caused by angular vibration are more complicated in the practical application environment. The output of FOG includes both effective angular information and dynamic error at this moment, which means that the dynamic error should be removed while the effective angular information must be retained. In this paper, we focus on the effect of angular vibration on FOG, and propose a dynamic error compensation method of FOG based on complete ensemble empirical mode decomposition with adaptive noise (CEEMDAN) that properly separates the effective signal and dynamic error. We also consider the amplitude frequency characteristics of FOG under dynamic conditions and utilize the FOG bandwidth test experiment to verify the effectiveness of our method. The experimental results show that the compensated signal can correctly calculate the bandwidth of FOG. It indicates that our method can effectively compensate the dynamic error in angular vibration environment while improving the performance of FOG in dynamic environment.
Software Compensation for the Coupling Error of a Single-Mode Fiber Coil under Time-Varying Temperature and Magnetic Field

Cui Liang,Jinhao Li,Wenqing Pan,Dengwei Zhang,Xiaowu Shu

DOI: https://doi.org/10.1117/1.oe.59.4.044102

IF: 1.3

2020-01-01

Optical Engineering

Abstract:Previous studies have shown that there exists a large nonreciprocal phase error in the single-mode fiber coil of a depolarized interference fiber optic gyroscope (De-IFOG) under time-varying temperature and magnetic field, which evidently weakens its environmental adaptability. A real-time software compensation method considering the coupling effect of time-varying temperature and magnetic field is first proposed and verified experimentally. After compensation, the error of De-IFOG decreases from 50 deg /h to 6 deg /h when the magnitude of the magnetic field is 10 G and temperature uniformly increases from 10 degrees C to 60 degrees C with time-varying rate of 36 degrees C/h. The compensation method is of great significance in De-IFOG engineering applications. (C) 2020 Society of Photo-Optical Instrumentation Engineers (SPIE)
Research on the Feedback Control Characteristics and Parameter Optimization of Closed-Loop Fiber Optic Gyroscope

Jingtao Yan,Lijun Miao,Min Chen,Tengchao Huang,Shuangliang Che,Xiaowu Shu

DOI: https://doi.org/10.1016/j.ijleo.2021.166298

IF: 3.1

2021-01-01

Optik

Abstract:The feedback parameter of closed-loop fiber optic gyroscope (FOG) in various engineering applications is discussed. It has been proved that unreasonable feedback parameter will cause great interference and serious distortion to the output signal. Therefore, we build a concise feedback control mode and obtain optimal range of feedback parameter. For different input signals concerned which nearly include all of the application scenarios in practice, detailed simulations and experiments are completed. The results show that the feedback parameter should be small in static applications and moderate for high response requirements. What is more, it should be relatively small when used in low-bandwidth measurement fields to ensure the response performance of low frequency signal and suppress high frequency noise and vice versa. This work plays an important guiding role for related parameter setting in the feedback control system of sensors, especially for gyroscope.
Analysis of Scale Factor Error for Open-loop Fiber Optic Gyroscope with A Digital Signal Processing System

Zhongwei Tan,Chuanchuan Yang,Ziyu Wang

DOI: https://doi.org/10.1364/acp.2013.af2i.23

2013-01-01

Abstract:We research the effect of the instability of the modulation depth and the nonlinearity of the modulating signal on the scale factor error for open-loop fiber optic gyroscope with a digital signal processing system.
Rapid and Precise Compensation of Scale Factor in a Fiber-Optic Gyroscope with a Twin-Peaks Source.

Weiran Wu,Tuohua Xian,Guodong Hu,Kejiang Zhou

DOI: https://doi.org/10.1364/ol.386518

IF: 3.6

2020-01-01

Optics Letters

Abstract:In this Letter, two gyro outputs containing identical rotation rates are produced by a twin-peaks light source with peak wavelengths of 1530 nm and 1560 nm. We demonstrate that the two outputs’ ratio κ can compensate for the temperature-induced scale factor drift in an interferometric fiber-optic gyroscope (IFOG). When the temperature ranged from − 10 ∘ C to 50°C, the scale factor drift after compensation was about 30 times less than that before compensation, and the minimum drift was ± 7.7 p p m at the rotation rate of 100°/s.
The Temperature Error Modeling and Compensation Method of Fiber Optic Gyroscope Scaling Factor

Fei Wang,Lei Wang,Shuai Zhao,Tengchao Huang,Xiaowu Shu

DOI: https://doi.org/10.1117/12.2607048

2021-01-01

Abstract:Fiber optic gyroscope (FOG) has the advantages of small size, light weight, large dynamic range, fast start up and long life. It can be widely used in military fields and civil fields. As the performance of the optoelectronic devices in the FOG varies with the temperature, the performance of the FOG will be affected. In the use of the carrier high speed, the scaling factor error caused by temperature change is the main error of the FOG, its effect on accuracy is much greater than random drift. FOG often needs to work in a wide temperature range, so the scaling factor needs to be modeled and compensated. Because of the temperature error of the scaling factor is very non-linear, the accuracy of using the traditional polynomial fitting method to compensate the scaling factor is poor. The neural network can approximate any continuous function with any desired accuracy, so this paper uses the BP neural network method to compensate the temperature error of the FOG scaling factor. First, this paper analyzes the error mechanism of the scaling factor, and establishes a theoretical model of the temperature error of the scaling factor. Then the FOG scaling factor in the full temperature range is measured, and the temperature error of the scaling factor is modeled and compensated by using the above two methods. It can be seen from the compensation results that the neural network model can get a good compensation effect, and the accuracy is better than the polynomial fitting method.
Study on Temperature Stability of Scale-Factor in Closed-Loop Fiber Optical Gyroscope

Yan-ji WU,Xian-lin HUANG

DOI: https://doi.org/10.3969/j.issn.1001-0645.2007.07.013

2007-01-01

Abstract:Based on closed-loop fiber optical gyroscopes, research work on the temperature stability of the scale-factor has been performed. The mathematical expression of the scale-factor has been established. The mechanism of temperature influence on the stability of scale-factor was analyzed. The coefficient of some parameters was given. An experiment on the temperature stability of the scale-factor has been performed in closed-loop fiber optical gyroscopes. It can be seen from the experimental results that the temperature sensitivity of the scale-factor has been changed from 8.08 × 10-4/°C to 1.70 × 10-5/°C.
Reduction of High-Frequency Laser Noise in Resonant Fiber Optic Gyroscope with a Phase-Modulated Feedback Loop

Sen Ye,Yi Lin,Hanzhao Li,Huihan Ma,Zhonghe Jin

DOI: https://doi.org/10.1109/icocn.2017.8121535

2017-01-01

Abstract:The resonant fiber-optic gyroscope (RFOG) based on the Sagnac effect is a high-accuracy rotation sensor. The intermodulation error due to the laser noise at even harmonics of the modulation frequency deteriorates the performance of the RFOG. Aiming at the suppression of high-frequency laser noise, a phase-modulated feedback loop is developed and analyzed. The parameters of the servo loop is optimized to enhance the performance of the gyroscope.
Interactive Errors Analysis and Scale Factor Nonlinearity Reduction Methods for Lissajous Frequency Modulated MEMS Gyroscope

Rui Li,Xiaoxu Wang,Kaichen Yan,Zhennan Chen,Zhengya Ma,Xiquan Wang,Ao Zhang,Qianbo Lu

DOI: https://doi.org/10.3390/s23249701

IF: 3.9

2023-12-08

Sensors

Abstract:Although the Lissajous frequency modulated (LFM) mode can improve the long-term and temperature stability of the scale factor (SF) for mode mismatch MEMS gyroscopes, its SF nonlinearity poses a significant limitation for full-scale accuracy maintenance. This paper examines the interaction effects among stiffness coupling, system phase delay, readout demodulation phase shift, and velocity amplitude mismatch within the control process. Based on the completion of frequency difference control and demodulation phase matching, we clarify that the remaining stiffness coupling and residual system phase error are the primary factors influencing SF nonlinearity. Furthermore, SF nonlinearity is reduced through error compensation. On one hand, this paper suppresses stiffness coupling through the observation of the instantaneous frequency difference and the application of the quadrature voltage. On the other hand, system phase error is compensated by observing the amplitude control force and tuning the reference in the Phase-Locked Loops (PLLs). Subsequent simulations of these methods demonstrated a remarkable 97% reduction in SF nonlinearity within the measurement range of ±500°/s. In addition, an observed rule dictates that maintaining a sufficiently large frequency split effectively constrains the SF nonlinearity.

engineering, electrical & electronic,chemistry, analytical,instruments & instrumentation

Compensation of Scale Factor Error for Open-loop Fiber Optic Gyroscopes

Scale Factor Calibration and Dynamic Angle Measurement Method Based on Self-Collimator and Fiber Optic Gyroscope

Compensation of Scale Factor Nonlinear Error Introduced by Harmonic Distortion for Open-Loop Fiber Optic Gyroscopes.

Theory And Error Compensation Method Based On The Tilt Sensor Adopted In Dynamic Angle Measurement Of The Fiber Optic Gyroscope

One-Dimensional Angle Measurement Error Calibration Technique for Fiber Optic Gyroscope

Theory and Compensation Method of Axial Magnetic Error Induced by Axial Magnetic Field in A Polarization-Maintaining Fiber Optic Gyro

Study on FOG Scale Factor Error Calibration in Start-Up Stage Based on GWO-GRU

Study on Nonlinear Error Calibration of Fiber Optical Gyroscope Scale Factor Based on LSTM

Performance Analysis of an Optical Passive Ring-Resonator Gyro with A Hollow-Core Photonic Bandgap Fiber Sensing Coil

Principle and Application of High Dynamic Fiber Gyroscope

Method to Suppress Scale Factor Error for All-Digital Signal Processing Open-loop Fiber-optic Gyroscope

Uncertainty Analysis of Dynamic Goniometer Based on Fiber Optic Gyroscope

Analysis of Fiber Optic Gyroscope Dynamic Error Based on CEEMDAN

Software Compensation for the Coupling Error of a Single-Mode Fiber Coil under Time-Varying Temperature and Magnetic Field

Research on the Feedback Control Characteristics and Parameter Optimization of Closed-Loop Fiber Optic Gyroscope

Analysis of Scale Factor Error for Open-loop Fiber Optic Gyroscope with A Digital Signal Processing System

Rapid and Precise Compensation of Scale Factor in a Fiber-Optic Gyroscope with a Twin-Peaks Source.

The Temperature Error Modeling and Compensation Method of Fiber Optic Gyroscope Scaling Factor

Study on Temperature Stability of Scale-Factor in Closed-Loop Fiber Optical Gyroscope

Reduction of High-Frequency Laser Noise in Resonant Fiber Optic Gyroscope with a Phase-Modulated Feedback Loop

Interactive Errors Analysis and Scale Factor Nonlinearity Reduction Methods for Lissajous Frequency Modulated MEMS Gyroscope