Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Formability Prediction for Thermal Stamping of Magnesium Alloy Sheet Based on M-K Model

Study on Simulation of Stamping Forming and Die Surface Optimization of Aluminum Alloy Plate

A Method for Prediction of Forming Strain for Cold Stamping Formed Head Made of S30408 Austenitic Stainless Steel

M–K model based forming limit prediction of aluminum–lithium alloy 2060 and its application in hot stamping

Numerical Simulation of Hot Stamping Forming of AZ Series Magnesium Alloys and Optimization of Die Process

Experimental Research on Formability of Stamping of AZ31B Magnesium Alloy Sheets

Thermo-mechanical coupled simulation of hot stamping components for process design

Failure prediction of magnesium alloys based on improved CDM model

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

FEM model optimization study of mechanical properties and material selection in stamping process

Numerical Modeling of Magnesium Alloy Sheet Metal Forming at Elevated Temperature

Machine learning in the prediction of formability in aluminum hot stamping process with multiple variable blank holder force

Formability Prediction Using Machine Learning Combined with Process Design for High-Drawing-Ratio Aluminum Alloy Cups

An improved Marciniak-Kuczynski approach for predicting sheet metal formability

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

A new predicting model study on U-shaped stamping springback behavior subjected to steady-state temperature field

The prediction of part thickness using machine learning in aluminum hot stamping process with partition temperature control

Numerical simulation and experimental study of warm hydro-forming of magnesium alloy sheet

M–K Ductile Damage Theory Predicts Formability of Stainless Steel Ultra-Thin Strips in Stamping

Energy-Economizing Optimization of Magnesium Alloy Hot Stamping Process

Numerical modeling of the thermal deformation during stamping process of an automotive body part