Abstract:The demand for advanced Al-based alloys with tailored structural and magnetic properties has intensified for applications requiring a high thermal stability and performance under challenging conditions. This study investigated the phase evolution, magnetic properties, thermal stability, and microstructural changes in the Al-based alloys Al82Fe16Nb2 and Al82Fe14Nb2Mn2, synthesized via mechanical alloying (MA), using stearic acid as a process control agent. The X-ray diffraction results indicated that Al82Fe16Nb2 achieved a β-phase solid solution with 13–14 nm crystallite sizes after 5 h of milling, reaching an amorphous state after 10 h. In contrast, Al82Fe14Nb2Mn2 formed a partially amorphous structure within 10 h, with enhanced stability with additional milling. Magnetic measurements indicated that both alloys possessed soft magnetic behavior under shorter milling times (1–5 h) and transitioned to hard magnetic behavior as amorphization progressed. This phenomenon was associated with a decrease in saturation magnetization (Ms) and an increase in coercivity (Hc) due to structural disorder and residual stresses. Thermal stability analyses on 10 h milled samples conducted via differential scanning calorimetry showed exothermic peaks between 300 and 800 °C, corresponding to phase transformations upon heating. Post-annealing analyses at 550 °C demonstrated the presence of phases including Al, β-phase solid solutions, Al13Fe4, and residual amorphous regions. At 600 °C, the Al3Nb phase emerged as the β-phase, and the amorphous content decreased, while annealing at 700 °C fully decomposed the amorphous phases into stable crystalline forms. Microstructural analyses demonstrated a consistent reduction in and homogenization of particle sizes, with particles decreasing to 1–3 μm in diameter after 10 h. Altogether, these findings highlight MA's effectiveness in tuning the microstructure and magnetic properties of Al–Fe–Nb (Mn) alloys, making these materials suitable for applications requiring a high thermal stability and tailored magnetic responses.

Low-Temperature Mechanical Alloying of Cu-Fe and Cu-Ta Powders

The Effect of A Small Amount of Tungsten on the Microstructure of Mechanically Alloyed Ag37cu63

Eff ects of Diff erent Mechanical Alloying Parameters on Microstructure of High Temperature Nanocrystalline Cu-Ta Alloys

Amorphization in the AlC System by Mechanical Alloying

Metastable Structures of Immiscible System Induced by Mechanical Alloying

63Cu Nuclear Magnetic Resonance Analysis of Mechanical Alloying Processes in Copper-Zinc Powders

Mechanical alloying in the Fe–Cu system

Cu-63 Nmr-Study Of Cu83-Zn17 Mixed Powders During Mechanical Alloying

Study on mechanical alloying behavior and thermal stability of HfMoNbTaTi refractory high-entropy alloy

63Cu NMR Study of Cu83-Zn17Mixed Powders During Mechanical Alloying

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

Reduction reaction in Al-CuO powder mixture driven by mechanical alloying

Non-equilibrium solidification of bulk undercooled Ni–P eutectic alloys

THERMODYNAMICAL ANALYSIS ON THE METASTABLE TRANSITIONS OF A MULTI-PHASE Al3Ti-BASED INTERMETALLIC COMPOUND DURING HIGH-ENERGY BALL-MILLING

Effects of milling process parameters and PCAs on the synthesis of Al0.8Co0.5Cr1.5CuFeNi high entropy alloy powder by mechanical alloying

Mechanical Alloying as a Way to Produce Metastable Single-Phase High-Entropy Alloys beyond the Stability Criteria

Mechanical Alloying, Fine Structure and Thermal Decomposition of Nanocrystalline Fcc-Fe60cu40

Mechanical milling/alloying of intermetallics

Nanocrystalline/Amorphous Tuning of Al–Fe–Nb (Mn) Alloy Powders Produced via High-Energy Ball Milling

Transmission Electron Microscopy Studies of Mechanical Alloying in the Immiscible Fe2o3-Sno2 System

Mechanical Alloying of Immiscible Metallic Systems: Process, Microstructure, and Mechanism