Abstract:The demand for advanced Al-based alloys with tailored structural and magnetic properties has intensified for applications requiring a high thermal stability and performance under challenging conditions. This study investigated the phase evolution, magnetic properties, thermal stability, and microstructural changes in the Al-based alloys Al82Fe16Nb2 and Al82Fe14Nb2Mn2, synthesized via mechanical alloying (MA), using stearic acid as a process control agent. The X-ray diffraction results indicated that Al82Fe16Nb2 achieved a β-phase solid solution with 13–14 nm crystallite sizes after 5 h of milling, reaching an amorphous state after 10 h. In contrast, Al82Fe14Nb2Mn2 formed a partially amorphous structure within 10 h, with enhanced stability with additional milling. Magnetic measurements indicated that both alloys possessed soft magnetic behavior under shorter milling times (1–5 h) and transitioned to hard magnetic behavior as amorphization progressed. This phenomenon was associated with a decrease in saturation magnetization (Ms) and an increase in coercivity (Hc) due to structural disorder and residual stresses. Thermal stability analyses on 10 h milled samples conducted via differential scanning calorimetry showed exothermic peaks between 300 and 800 °C, corresponding to phase transformations upon heating. Post-annealing analyses at 550 °C demonstrated the presence of phases including Al, β-phase solid solutions, Al13Fe4, and residual amorphous regions. At 600 °C, the Al3Nb phase emerged as the β-phase, and the amorphous content decreased, while annealing at 700 °C fully decomposed the amorphous phases into stable crystalline forms. Microstructural analyses demonstrated a consistent reduction in and homogenization of particle sizes, with particles decreasing to 1–3 μm in diameter after 10 h. Altogether, these findings highlight MA's effectiveness in tuning the microstructure and magnetic properties of Al–Fe–Nb (Mn) alloys, making these materials suitable for applications requiring a high thermal stability and tailored magnetic responses.

THERMODYNAMICAL ANALYSIS ON THE METASTABLE TRANSITIONS OF A MULTI-PHASE Al3Ti-BASED INTERMETALLIC COMPOUND DURING HIGH-ENERGY BALL-MILLING

Metastable transformation and reordering of mult-phase Al3Ti-based intermetallics

EFFECTS OF HIGH-ENERGY BALL MILLING ON THE STRUCTURE AND PROPERTY OF A MULTIPHASE Al3Ti-BASED INTERMETALLIC ALLOY

Metastable state transformations of Al3Ti-base alloys during mechanical milling and subsequent annealing

Amorphization in the AlC System by Mechanical Alloying

Effects of high-energy ball milling on structure and mechanical properties of L12 intermetallic compound Al67Mn8Ti25

Multi-component Phase-Field Simulation of Microstructural Evolution and Elemental Distribution in Fe–Cu–Mn–Ni–Al Alloy

Formation of Nanocrystalline Fcc Phase by Mechanically Driven Crystallization

Structural Transition and Atomic Ordering of Ni49.8mn28.5ga21.7 Ferromagnetic Shape Memory Alloy Powders Prepared by Ball Milling

Effect of Aging and Ball Milling on the Phase Transformation of Ni50Mn25Ga17Cu8−xZrx Alloys

Fracture Behavior and Structural Transition of Ni46Mn33Ga17Cu4−Zr Alloys

Structural Transformations in Medium- and High-Entropy Alloy Systems in Course of High-Energy Ball Milling

Effect of ball-milling on the phase structure and hydrogen storage properties of Ti0.9Zr0.1Mn1.5 alloy

Nonequilibrium phase transformation of NdFe11Ti compound during mechanical milling

Microstructure and property of Al67Mn8Ti24Nb1 intermetallics consolidated with metasable powder

Preparation of Nb3al by High-Energy Ball Milling and Superconductivity

Phase Transformation and Morphology Evolution of Ti50Cu25Ni20Sn5 during Mechanical Milling

PHASE TRANSFORMATION IN ANNEALED MECHANICAL ALLOYING Nd-11Fe-Ti ALLOY AND ANNEALED MECHANICAL MILLING NdFe11Ti COMPOUND

Structural evolution during mechanical milling and subsequent annealing of Cu–Ni–Al–Co–Cr–Fe–Ti alloys

Effect of Milling Parameters on the Development of a Nanostructured FCC–TiNb15Mn Alloy via High-Energy Ball Milling

Nanocrystalline/Amorphous Tuning of Al–Fe–Nb (Mn) Alloy Powders Produced via High-Energy Ball Milling