Abstract:Spent petroleum hydroprocessing catalysts (HPCs) are considered hazardous waste due to their high content of heavy metals and organic pollutants , posing a risk of environmental pollution and significant loss of valuable metals if not properly disposed. This study aimed to characterize the spent HPCs using optical microscopy, SEM-EDS, XRF, C & S analyzer, XRD, and XPS. Additionally, the effectiveness of six organic solvents in removing the black oil covering the surface of spent HPCs was investigated. Furthermore, the recovery of Mo, V, and Al from the spent HPCs was examined through stepwise leaching using NaOH + NaClO 2 and NaOH, followed by the separation of Mo, V, and Al via selective precipitation of Al and solvent extraction using Aliquat 336. The results indicated that toluene and tetrahydrofuran exhibited the highest efficiency in removing the black oil. Under the optimized oxidizing alkaline leaching conditions (0.09 g/mL NaOH + 0.05 g/mL NaClO 2 , 90 °C, 1 h), Mo, V, and Al achieved leaching efficiencies of 99.9 %, 99.9 %, and 20.1 %, respectively. Subsequently, Al in the residue was recovered through leaching with NaOH, resulting in a total leaching efficiency of 95 % under the optimized alkaline leaching conditions (0.12 g/mL NaOH, 180 °C, 3 h). The Al in both leaching solutions was precipitated by adjusting the pH to 8.60. For the subsequent Mo/V separation, the best conditions involved either four stages of counter-current extraction or two stages of cross-current extraction using a solution of 21 wt% Aliquat 336 dissolved in a mixture of kerosene and isooctanol (volume ratio 9:1) at a pH of 8.60. Finally, a hydrometallurgical flowchart for the recovery of Mo, V, and Al from spent HPCs was proposed.

Recovery of Hazardous Metals from Spent Refinery Processing Solid Catalyst

Negligible emissions and highly efficient recovery of Mo, V, and Al from spent hydroprocessing catalysts through alkaline leaching and solvent extraction

Sustainable recovery of surface-deposited oils and valuable metals from uncrushed spent hydroprocessing catalysts

Efficient Recovery of All Valuable Metals from Spent HDS Catalysts: Based on Roasting Mechanisms for Enhanced Selective Leaching and Separation

Stepwise separation and recovery of molybdenum, vanadium, and nickel from spent hydrogenation catalyst

Study on the Recycling of Valuable Metals in Spent Al2O3-based Catalyst

Recovering valuable metals from spent hydrodesulfurization catalyst via blank roasting and alkaline leaching

Efficient and Selective Recovery of Mo and V from Spent Hydrodesulfurization Catalysts Via Oxidation Roasting Followed by Na2CO3 and NaOH Leaching

Recovery of Nickel, Cobalt, and Aluminum from Molybdenum Extraction Residue of Spent Hydrodesulfurization Catalyst

A Promising Approach to Recover a Spent SCR Catalyst: Deactivation by Arsenic and Alkaline Metals and Catalyst Regeneration

Recovery and value-added utilization of critical metals from spent catalysts for new energy industry

Recovery of rare earths from spent FCC catalysts by solvent extraction using saponified 2-ethylhexyl phosphoric acid-2-ethylhexyl ester (EHEHPA)

Alkali extraction of valuable metals from spent Mo–Ni/Al 2 O 3 catalyst

Separation and Recovery of Vanadium, Nickel, and Aluminum from Acid Leaching Solution of Spent Hydrodesulfurization Catalyst by a Solvent Extraction-Oxalic Acid Precipitation Process

Synchronous conversion and targeted separation of valuable metals from spent hydroprocessing catalysts

Recovery of rare earth elements from spent fluid catalytic cracking catalysts using leaching and solvent extraction techniques

Recovery of Mo and Ni from spent acrylonitrile catalysts using an oxidation leaching–chemical precipitation technique

Cleaner recycling of spent Ni–Mo/γ-Al2O3 catalyst based on mineral phase reconstruction

Organic acid-mediated leaching kinetics study and selective extraction of Mo, V, and Ni from spent catalysts

Recovery of Rare Earth Elements from Spent Fluid Catalytic Cracking Catalyst Using Hydrogen Peroxide As a Reductant

Recovery of Aluminum from Molybdenum Extraction Residue of Spent Hydrodesulfurization Catalyst