Abstract:The prediction of mass transfer rate is one of the key elements for estimation of the flow accelerated corrosion (FAC) rate. Three low Reynolds number (LRN) k–ɛ models (Lam–Bremhorst (LB), Abe–Kondoh–Nagano (AKN) and Hwang–Lin (HL)), one LRN k–ω (Wilcox, WX) model and the k–ω SST model are tested for the computation of the high Schmidt number mass transfer, especially in the flow through an orifice. The models are tested in the computation of three types of flow: (1) the fully developed pipe flow, (2) the flow over a backward facing step, (3) the flow through an orifice. The HL model shows a good performance in predicting mass transfer in the fully developed pipe flow but fails to give reliable prediction in the flow through an orifice. The WX model and the k–ω SST model underpredict the mass transfer rate in the flow types 1 and 3. The LB model underestimates the mass transfer in the flow type 1, but shows abnormal behavior at the reattaching point in type 3. Synthetically evaluating all the models in all the computed case, the AKN model is the best one; however, the prediction is still not satisfactory. In the evaluation in the flow over a backward facing step shows k–ω SST model shows superior performance. This is interpreted as an implication that the combination of the k–ɛ model and the stress limiter can improve the model behavior in the recirculation bubble. Both the stress limiter similar to that utilized in WX and SST model and Kato–Launder modification are implemented in the AKN model and help to lower the peak of mass transfer coefficient, while raising the values in the downstream. The value of turbulent Schmidt number is also investigated in this paper. If a uniform value is used, Sct≈1.0 can be reasonable in the case of high Schmidt mass transfer. Sct=1.71(y+)−0.38 can be used to predict the high Schmidt mass transfer in the simple flows.

ICONE19-43282 TURBULENCE MODELING FOR MASS TRANSFER IN SEPARATED AND REATTACHING FLOWS FOR FLOW-ACCELERATED CORROSION

Turbulence Modeling for Mass Transfer Enhancement by Separation and Reattachment with Two-Equation Eddy-Viscosity Models

A Mixed-Time-scale Low-Reynolds-number One-Equation Turbulence Model

Numerical Investigation on Local Non-equilibrium Flows Using a Diatomic Nonlinear Constitutive Model

Analytical Method of Nonlinear Coupled Constitutive Relations for Rarefied Non-Equilibrium Flows

A Computational Strategy for Nonlinear Coupled Constitutive Relations of Rarefied Nonequilibrium Flows on Unstructured Grids

Numerical Predictions of Uniform CO2 Corrosion in Complex Fluid Domains Using Low Reynolds Number Models

Prediction of Forced Gas Flows in Circular Tubes at High Heat Fluxes Accompanied by Laminarization

Numerically Investigating the Influence of Local Flow Behaviors on Flow-Accelerated Corrosion Using Two-Fluid Equations

CFD Modeling of Mass Transfer in the Flow Through an Orifice with Ζ-Fmodel

Turbulence Models for Fluid Flow and Heat Transfer Between Cross-Corrugated Plates

Turbulent transition simulation using the k–ω model

Modelling Flow Transition in a Hypersonic Boundary Layer with Reynolds-averaged Navier-Stokes Approach

Study of Hydrofoil Boundary Layer Prediction with Two Correlation-Based Transition Models

A Scale-Adaptive Turbulence Model Based on the k-Equation and Recalibrated Reynolds Stress Constitutive Relation

Numerical Simulation of Flow Around Square Cylinder Using Different Low-Reynolds Number Turbulence Models

Coarse-grid simulations of full-loop gas-solid flows using a hybrid drag model: Investigations on turbulence models

Studies on the Critical Heat Flux in Fuel Assembly Using a Modified Two-Phase Multi-Scale Interface Model-Validation and Sensitivity Analysis

Effects of Interaction Models on Upward Subcooled Boiling Flow in Annulus

SIMULATION OF SEPARATED FLOWS FOR THE NREL AIRFOIL USING ANISOTROPIC TWO-EQUATION TURBULENCE MODELS

Numerical Modeling of Freestream Turbulence Decay Using Different Commercial Computational Fluid Dynamics Codes