Turbulent Transition Simulation Using Thek-Ω Model
Feng Liu
DOI: https://doi.org/10.1002/(sici)1097-0207(19980715)42:5<907::aid-nme393>3.0.co;2-t
IF: 3.021
1998-01-01
International Journal for Numerical Methods in Engineering
Abstract:International Journal for Numerical Methods in EngineeringVolume 42, Issue 5 p. 907-926 Research Article Turbulent transition simulation using the k–ω model Xiaoqing Zheng, Corresponding Author Xiaoqing Zheng Front Range Scientific Computations, Inc., CO, U.S.A Research Scientist34 Beecher Place, #2, Newton, MA 02159, U.S.A.Search for more papers by this authorChaoqun Liu, Chaoqun Liu Department of Mathematics and Statistics, Louisiana Tech University, U.S.A Associate ProfessorSearch for more papers by this authorFeng Liu, Feng Liu Department of Mechanical and Aerospace Engineering, University of California, Irvine, CA, U.S.A Associate ProfessorSearch for more papers by this authorCheng-I Yang, Cheng-I Yang Hydromechanics Directorate, Carderock Division, NSWC Bethesda, MD, U.S.A Research ScientistSearch for more papers by this author Xiaoqing Zheng, Corresponding Author Xiaoqing Zheng Front Range Scientific Computations, Inc., CO, U.S.A Research Scientist34 Beecher Place, #2, Newton, MA 02159, U.S.A.Search for more papers by this authorChaoqun Liu, Chaoqun Liu Department of Mathematics and Statistics, Louisiana Tech University, U.S.A Associate ProfessorSearch for more papers by this authorFeng Liu, Feng Liu Department of Mechanical and Aerospace Engineering, University of California, Irvine, CA, U.S.A Associate ProfessorSearch for more papers by this authorCheng-I Yang, Cheng-I Yang Hydromechanics Directorate, Carderock Division, NSWC Bethesda, MD, U.S.A Research ScientistSearch for more papers by this author First published: 04 December 1998 https://doi.org/10.1002/(SICI)1097-0207(19980715)42:5<907::AID-NME393>3.0.CO;2-TCitations: 24 AboutPDF ToolsRequest permissionExport citationAdd to favoritesTrack citation ShareShare Give accessShare full text accessShare full-text accessPlease review our Terms and Conditions of Use and check box below to share full-text version of article.I have read and accept the Wiley Online Library Terms and Conditions of UseShareable LinkUse the link below to share a full-text version of this article with your friends and colleagues. Learn more.Copy URL Share a linkShare onEmailFacebookTwitterLinkedInRedditWechat Abstract This paper describes a novel approach in simulating laminar to turbulent transition by using two-equation models. The Total Stresses Limitation (TSL) concept is used to make the two-equation model capable of predicting high-Reynolds-number transitional flow. In order to handle the transition triggered by laminar separation at a low Reynolds number location, which commonly occurs in high speed flow, a sensor is introduced to detect separation and trigger transition in the separated zone. Test cases include the classical flat-plate turbulent boundary flow, and low-pressure turbine cascade flows at design and off-design conditions. © 1998 John Wiley & Sons, Ltd. References 1 C. Liu and Z. Liu, 'Multigrid mapping and box relaxation for simulation of the whole process of flow transition in 3-D boundary layers', J. Comput. Phys., 119, 325–341 (1995). 2 Z. Liu, G. Xiong and C. Liu, ' Direct numerical simulation for the whole process of transition on 3-D airfoils', AIAA Paper 96-2081, June 1996. 3 A. M. O. Smith and N. Gamberoni, ' Transition, pressure gradient and stability theory', Douglas Aircraft Co. Report ES 26388, EL Segundo, California, 1956. 4 J. L. Van Ingen, ' A suggested semi-empirical method for the calculation of the boundary layer transition region', Report UTH-74, Department of Aerospace Engineering, University of Technology, Delft, 1956. 5 G. Casalis, M. L. Copie, Ch. Airiau and D. Arnal, ' Nonlinear analysis with PSE approach', in P. W. Duch and P. Hall (eds.), IUTAM Symp. on Nonlinear Instability and Transition in Three-Dimensional Boundary Layers, Kluwer Academic Publishers, Dordrecht, 1996, pp. 237–246. 6 D. Arnal, G. Casalis and J. C. Juillen, ' A survey of the transition prediction methods: from analytical criteria to PSE and DNS', in M. Hallback (ed.), Turbulence and Transition Modelling, Lecture Notes from the ERCOFTAC/IUTAM Summer School Held in Stockholm, 12–20 June 1995, Kluwer Academic Publishers, Dordrecht, 1996, pp. 3–14. 7 J. Steelant and E. Dick, 'Modelling of bypass transition with conditioned Navier-Stokes equations coupled to an intermittency transport equation', Int. J. Numer. Meth. Fluids, 23, 193–220 (1996). 8 E. Dick and J. Steelant, 'Coupled solution of the steady compressible Navier-Stokes equations and the k- e turbulence equations with a multigrid method', Appl. Numer. Math., 23, 49–61 (1997). 9 R. C. Schmidt and S. V. Patankar, 'Simulating boundary layer transition with low-Reynolds number k- e turbulence models: Part 1–an evaluation of prediction characteristics', J. Turbomachinery, 113, 10–17 (1991). 10 D. C. Wilcox, 'Simulation of transition with a two-equation turbulence model', AIAA J., 32 (2), 247–255 (1994). 11 X. Zheng and F. Liu, 'Staggered upwind method for solving Navier-Stokes and k- w turbulence model equations', AIAA J., 33 (6), 991–998 (1995). 12 X. Zheng, C. Liao, C. Liu, C. Sung and T. Huang, ' Multiblock multigrid incompressible flows using two-equation turbulence models', AIAA Paper 97-0626, January 1997. 13 D. C. Wilcox, 'Alternative to the e9 procedure for predicting boundary-layer transition', AIAA J., 19 (1), 56–64 (1981). 14 H. P. Hodson, ' Boundary layer transition and separation near the leading edge of a high speed turbine blade', ASME Paper 84-GT-179. Also in ASME J. Engng. Gas Turbines Power, 107, (1985). 15 H. P. Hodson and R. G. Dominy, ' Three-dimensional flow in a low pressure turbine cascade at its design condition', ASME Paper 86-GT-106, 1986. Also in, ASME J. Turbomachinery, 109, 177–185 (1987). 16 H. P. Hodson and R. G. Dominy, ' The off-design performance of a low pressure turbine cascade', ASME Paper 86-GT-188, 1986. Also in, ASME J. Turbomachinery, 109, 201–209 (1987). 17 F. Liu and X. Zheng, 'A staggered finite volume scheme for solving cascade flow with a two-equation model of turbulence', AIAA J., 32 (8), 1589–1597 (1994). 18 P. L. Roe, 'Approximate Riemann solvers, parameter vectors, and difference schemes', J. Comput. Phys., 43 (3), 357–372 (1981). 19 A. Jameson, W. Schmidt and E. Turkel, ' Numerical solutions of Euler equations by finite volume methods using Runge-Kutta time-stepping schemes', AIAA-81-1259, 1981. 20 F. Liu and X. Zheng, 'A strongly coupled time-marching method for solving the Navier-Stokes and k- w turbulence model equations with multigrid', J. Comput. Phys., 128, 289–300 (1996). 21 F. R. Menter, 'Influence of freestream values on k- w turbulence model predictions', AIAA J., 30 (6), 1657–1659 (1992). 22 D. C. Wilcox, 'Reassessment of the scale-determining equation for advanced turbulence models', AIAA J., 26 (11), 1299–1310 (1988). 23 D. C. Wilcox, ' A half century historical review of the k-w model', AIAA 91-0615, 1991. Citing Literature Volume42, Issue515 July 1998Pages 907-926 ReferencesRelatedInformation
What problem does this paper attempt to address?
-
A Mixed-Time-scale Low-Reynolds-number One-Equation Turbulence Model
Xin Wu,Ping Ju,Feng Wu
DOI: https://doi.org/10.1080/14685248.2013.802095
2013-01-01
Journal of Turbulence
Abstract:In this paper, a new low-Reynolds-number (LRN) one-equation turbulence model for eddy viscosity is proposed. A mixed time scale, representing a combination of three time scales: two time scales made of strain-rate parameter S and vorticity parameter and the turbulent time scale k/E, is introduced into this model. The proposed model is derived from an LRN k-E two-equation model where the mixed time scale has been proved to be very effective for predicting local flows over complex terrains. In the transport equation of the model, the mixed time scale is included in the production and the dissipation terms. The new model is evaluated in channel flows at various Reynolds numbers, boundary layer flows with or without pressure gradient and backward-facing step flows with different expansion ratios and Reynolds numbers. Then the grid convergence of the model is investigated. Finally, the model performance for different values of the weighting constant C-s in the mixed time scale is assessed. The results show that the proposed model reproduces the correct wall-limiting behaviour of turbulent quantities and performs well in the near-wall region of turbulent flows. The model could be expected to be adopted in hybrid Reynolds averaged Navier-Stokes/large eddy simulation methodology for complex wall-bounded flows at high Reynolds numbers.
-
Gas-Kinetic Scheme Coupled with Turbulent Kinetic Energy Equation for Computing Hypersonic Turbulent and Transitional Flows
Hualin Liu,Guiyu Cao,Weifang Chen,Ramesh K. Agarwal,Wenwen Zhao
DOI: https://doi.org/10.1080/10618562.2021.1942860
IF: 1.443
2021-01-01
International Journal of Computational Fluid Dynamics
Abstract:For simulation of hypersonic turbulent and transitional flows at high Reynolds numbers, a gas-kinetic scheme (GKS) strongly coupled with the turbulent kinetic energy equation in shear stress transport (SST) k-omega turbulence model is developed. To extend the current method to transitional flows, Langtry-Menter gamma - Re-0 transition model is added together with SST k-omega turbulence model. Comparisons among the numerical solutions from current GKS method coupled with turbulent kinetic energy equation, GKS method uncoupled with turbulent kinetic energy equation, Reynolds-Averaged Navier-Stokes (RANS) solutions with turbulence/transition models, and experimental data are conducted. It is concluded that the current method can significantly improve the accuracy of numerical results.
-
Application of simplified threeGequation transition model in hypersonic flow
CAILinfeng,LIHaoge,Wenwen ZHAO,Weifang? CHEN
DOI: https://doi.org/10.7638/kqdlxxbG2017.0172
2019-01-01
Abstract:On the basis of the RANS model,the numerical simulation study of hypersonic boundary﹣layer transitional flow was carried out on a flat﹣plate,a double wedge,and a cone by modifying k﹣ω SST turbulence model and the intermittency transition model with compressibility correction.Based on the comparison with experimental result,it is shown that the simplified three﹣equation transition model based on the pressure gradient characterization parameter Tw=R TΩ/ω can correctly catch the transition onset location,the length of transition region,and the turbulent zone heat flux on the wall for the flat﹣plate hypersonic boundary﹣layer flow.For the double wedge and cone case,the wall heat flux in turbulent zone calculated by the simplified three﹣equation transition model is much higher than the experimental data due to the flow compression effects.However, it can agree well with the experimental data after adding compressibility correction to the model.The simplified three﹣equation transition model with appropriate compressibility correction has potential to simulate hypersonic boundary﹣layer transitional flow correctly.
-
Modelling Flow Transition in a Hypersonic Boundary Layer with Reynolds-averaged Navier-Stokes Approach
Liang Wang,Song Fu
DOI: https://doi.org/10.1007/s11433-009-0047-8
2009-01-01
Abstract:Based on Reynolds-averaged Navier-Stokes approach, a laminar-turbulence transition model is proposed in this study that takes into account the effects of different instability modes associated with the variations in Mach numbers of compressible boundary layer flows. The model is based on k-ω-γ three-equation eddy-viscosity concept with k representing the fluctuating kinetic energy, ω the specific dissipation rate and the intermittency factor γ. The particular features of the model are that: 1) k includes the non-turbulent, as well as turbulent fluctuations; 2) a transport equation for the intermittency factor γ is proposed here with a source term set to trigger the transition onset; 3) through the introduction of a new length scale normal to wall, the present model employs the local variables only avoiding the use of the integral parameters, like the boundary layer thickness δ, which are often cost-ineffective with the modern CFD (Computational Fluid Dynamics) methods; 4) in the fully turbulent region, the model retreats to the well-known k-ω SST (Shear Stress Transport) model. This model is validated with a number of available experiments on boundary layer transitions including the incompressible, supersonic and hypersonic flows past flat plates, straight/flared cones at zero incidences, etc. It is demonstrated that the present model can be successfully applied to the engineering calculations of a variety of aerodynamic flow transition.
-
A modular RANS approach for modelling laminar-turbulent transition in turbomachinery flows
Liang Wang,Song Fu,Angelo Carnarius,Charles Mockett,Frank H. Thiele
DOI: https://doi.org/10.1016/j.ijheatfluidflow.2012.01.008
IF: 2.643
2012-01-01
International Journal of Heat and Fluid Flow
Abstract:In this study we propose a laminar-turbulent transition model, which considers the effects of the various instability modes that exist in turbomachinery flows. This model is based on a K- ω- γ three-equation eddy-viscosity concept with K representing the fluctuating kinetic energy, ω the specific dissipation rate and γ the intermittency factor. As usual, the local mechanics by which the freestream disturbances penetrate into the laminar boundary layer, namely convection and viscous diffusion, are described by the transport equations. However, as a novel feature, the non-local effects due to pressure diffusion are additionally represented by an elliptic formulation. Such an approach allows the present model to respond accurately to freestream turbulence intensity properly and to predict both long and short bubble lengths well. The success in its application to a 3-D cascade indicates that the mixed-mode transition scenario indeed benefits from such a modular prediction approach, which embodies current conceptual understanding of the transition process. © 2012 Elsevier Inc.
-
PROGRESS IN TURBULENCE/TRANSITION MODELLING
FU Song,WANG Liang
DOI: https://doi.org/10.3321/j.issn:1000-0992.2007.03.008
2007-01-01
Abstract:One of the effective approaches to simulating laminar-turbulent transition flows is the transition/ turbulence modeling based on Reynolds-averaged Navier-Stokes equations.In this paper,its development is reviewed.First,we analyze the limitations of the so called low-Reynolds number turbulence models for transitional flows.These models,with modified damping functions for the viscous sublayer,seem to have some ability for transition prediction,while it is argued that it is just a chance coincident in numerical simulation. Second,the correlation-based transition models are discussed.These models,always constructed by considering the intermittency factor,take into account the physical mechanism of transition in some extent,thus can model the transition procedure in several simple flows.Unfortunately,it is not easy to make these models compatible with modern CFD methods because of the non-local variables in model equations.Thirdly,based completely on local variables,some recently proposed transition models related to the new transport equations of laminar kinetic energy,transitional momentum thickness,Reynolds number and other characteristic parameters are analyzed.Finally,the future challenges are pointed out.
-
A NEW TRANSITION/TURBULENCE MODEL FOR THE FLOW TRANSITION IN SUPERSONIC BOUNDARY LAYER
王亮,符松
DOI: https://doi.org/10.3321/j.issn:0459-1879.2009.02.003
2009-01-01
Abstract:A new κ-ω-γ transition/turbulence model is established to consider the instability modes associated with the compressibility. The particular features of the new model are: (1) the fluctuating kinetic energy κ includes the non-turbulent, as well as turbulent components modelled with the stability analysis; (2) a function for the source term in γ equation is developed to trigger the transition onset; (3) it is strictly based on local variables by introducing a new length scale normal to wall and compatible with the modern CFD methods. The present model was numerically proved to be applied into the analyses of natural transition and bypass transition with a wide range of Mach number.
-
A Primary Study of Transitions in Turbulence Models
Fu Song
DOI: https://doi.org/10.3969/j.issn.1001-246X.2006.01.010
2006-01-01
Abstract:The Navier-Stokes equations are solved with the second-order LU-SGS-τTS implicit time-stepping method.The sixth-order symmetric TVD scheme with fifth-order WENO interpolation based on Roe is applied to the convection terms.A boundary layer flow around a flat plate,a low speed flow around the Aerospatial A-profile at high incidence and a transonic flow with shock/boundary interaction around RAE2822 airfoil are computed by Baldwin-Lomax and Spalart-Allmaras models with the transition criterion,respectively.The results show that the approaches capture the transition automatically.
-
Numerical Simulation of a Toroidal Single-Phase Natural Circulation Loop with a K-Kl-ω Transitional Turbulence Model
Yiwa Geng,Xiongbin Liu,Xiaotian Li,Yajun Zhang
DOI: https://doi.org/10.1016/j.net.2023.09.030
IF: 2.817
2024-01-01
Nuclear Engineering and Technology
Abstract:The wall friction correlations of oscillatory natural circulation loops are highly loop-specific, making it difficult to perform 1-D system simulations before obtaining specific experimental data. To better predict the friction characteristics, the nonlinear dynamics of a toroidal single-phase natural circulation loop were numerically investigated, and the transition effect was considered. The k-kL-ω transitional turbulence and k-ω SST turbulence models were used to compute the flow characteristics of the loop under different heating powers varying from 0.48 to 1.0 W/cm2, and the results of both models were compared with previous experiments. The mass flow rates and friction factors predicted by the k-kL-ω model showed a better agreement with the experimental data than the results of the k-ω SST model. The oscillation frequencies calculated using both models agreed well with the experimental data. The k-kL-ω transitional turbulence model provided better friction-factor predictions in oscillatory natural circulation loops because it can reproduce the temporal and spatial variation of the wall shear stress more accurately by capturing the movement of laminar, transition turbulent zones inside unstable natural circulation loops. This study shows that transition effects are a possible explanation for the highly loop-specific friction correlations observed in various oscillatory natural circulation loops.
-
Computation of Hypersonic Turbulent and Transitional Flows Using an Extended Gas Kinetic Scheme
Hualin Liu,Ramesh K. Agarwal,Weifang Chen
DOI: https://doi.org/10.2514/6.2022-1050
2022-01-01
Abstract:In this paper, an extended Gas-Kinetic Scheme (GKS) is developed to predict the hypersonic turbulent and transitional flows. By using an extended Maxwellian distribution function together with a BGK-type equation, the extended GKS method is obtained. The main innovation is the addition of the turbulent kinetic energy term into the gas distribution function. To be specific, the turbulent kinetic energy term is treated similar to an internal energy term and is added to the Maxwellian distribution function. This allows the current GKS scheme to couple the molecular motion of the gas with its turbulent kinetic energy in one probability density function. GKS is coupled with turbulent kinetic energy (TKE) equation in SST k-ω turbulence model to compute hypersonic turbulent flows and with the TKE equation in Langtry-Menter four equations SST k – ω - γ - Reθt transition model for computing hypersonic transitional flows. In order to demonstrate the high accuracy and numerical stability of the proposed method, several hypersonic turbulent and transitional flow cases are computed. The results from the current method are compared with the standard finite-volume solutions of Reynolds-Averaged Navier-Stokes (RANS) equations and experimental data; an excellent agreement between the current method and experimental data is obtained.
-
Simultaneous Simulation of Transition and Massive Separation by RANS-LES-Tr Model
Guangxing Wang,Zhixiang Xiao,Lianzhong Chen
DOI: https://doi.org/10.1016/j.ast.2020.106026
IF: 5.457
2020-01-01
Aerospace Science and Technology
Abstract:To predict complex flow, including transition on the windward side and massive separation on the leeward side, a Reynolds averaged Navier Stokes-Large Eddy Simulation (RANS-LES) hybrid model based on the three-equation k-ω-γ transition model (RANS-LES-Tr) was developed. Then, it was applied to simulate the following three cases, such as the low-speed flow past a cylinder only with the first transition mode, the low-speed prolate spheroid flow at a high angle of attack (AoA) with both the first and crossflow modes; and hypersonic flow past the “Orion” capsule with the first, second and crossflow modes. RANS-LES-Tr shows much better agreements with available measurements, such as skin friction and heat flux on the windward side, than RANS-LES based on the full turbulence model.
-
Transition Modeling for Low Pressure Turbines Using Computational Fluid Dynamics Driven Machine Learning
Harshal D. Akolekar,Fabian Waschkowski,Yaomin Zhao,Roberto Pacciani,Richard D. Sandberg
DOI: https://doi.org/10.3390/en14154680
IF: 3.2
2021-01-01
Energies
Abstract:Existing Reynolds Averaged Navier–Stokes-based transition models do not accurately predict separation induced transition for low pressure turbines. Therefore, in this paper, a novel framework based on computational fluids dynamics (CFD) driven machine learning coupled with multi-expression and multi-objective optimization is explored to develop models which can improve the transition prediction for the T106A low pressure turbine at an isentropic exit Reynolds number of Re2is=100,000. Model formulations are proposed for the transfer and laminar eddy viscosity terms of the laminar kinetic energy transition model using seven non-dimensional pi groups. The multi-objective optimization approach makes use of cost functions based on the suction-side wall-shear stress and the pressure coefficient. A family of solutions is thus developed, whose performance is assessed using Pareto analysis and in terms of physical characteristics of separated-flow transition. Two models are found which bring the wall-shear stress profile in the separated region at least two times closer to the reference high-fidelity data than the baseline transition model. As these models are able to accurately predict the flow coming off the blade trailing edge, they are also able to significantly enhance the wake-mixing prediction over the baseline model. This is the first known study which makes use of ‘CFD-driven’ machine learning to enhance the transition prediction for a non-canonical flow.
-
Modeling Separated Flow Transition with a Transport Intermittency Model
L. Wang,S. Fu,A. Carnarius,C. Mockett,F. Thiele
DOI: https://doi.org/10.1615/ichmt.2009.turbulheatmasstransf.1720
2009-01-01
Abstract:In this study we propose a local-variable-based laminar-turbulence transition model that considers the effects of different instability modes existing in separated flows. This model is based on k-omega-gamma three-equation eddy-viscosity concept with k representing the fluctuating kinetic energy, omega the specific dissipation rate and the intermittency factor gamma. It takes into account not only the local effects that the freestream disturbances penetrate into the laminar boundary layer by convection and viscous diffusion, as described by the transport equations, but also the non-local effect that by pressure diffusion, as represented by an elliptic approach. Such attempt makes the present model responding to freestream turbulence intensity properly and predicting both the long and short bubble length well, which indicates that the mixed-mode transition scenario do benefit from such a modular prediction approach that mirrors the conceptual understanding of the transition process.
-
A Modular RANS Approach for Modeling Hypersonic Flow Transition on an Air-Breathing Configuration
Lianghua Xiao,Liang Wang,Song Fu,Zhixiang Xiao
DOI: https://doi.org/10.2514/6.2013-671
2013-01-01
Abstract:In this study, the laminar-turbulent flow transition scenario on a blunted double ramp, and further on a 20%-scale X-51A forebody configuration, has been simulated with a recently proposed RANS (Reynolds-Averaged Navier-Stokes) transition/turbulence model, which takes into account of the rational effects of compressibility, crossflow and flowseparation characteristics on different instability modes in 3-D boundary-layer flows. The model is based on the K-ω-γ three-equation eddy-viscosity concept with K representing the fluctuating kinetic energy, ω the specific dissipation rate and γ the intermittency factor. This model performs pretty well in the blunted double ramp case, where the hypersonic flow transition is caused by flow separation at the compression corner. For the X-51A forebody configuration, computed results are in good agreement with experimental data under both quiet and noisy conditions.
-
Direct Numericalsimulation of Separated-Flow Transition in Low-Pressure Turbine
S. Jiang,S. Fu
DOI: https://doi.org/10.1615/thmt-18.1090
2018-01-01
Abstract:Numerical simulations of a low-pressure turbine (LPT) cascade have been performed with both RANS solver and DNS solver. Transition models with RANS solver cannot reproduce the transition process well in separation bubbles because the transport equation for intermittency factor gamma does not contain enough physical mechanisms. Therefore, DNS data is provided to examine the nature of instability mechanisms leading to separated-flow transition under low turbulent intensity. In DNS results, both K-H instability in the separated shear layer and viscous T-S instability in the near wall region are observed. Hyperbolic instability is found in transitionalprocess. The streamwise vortices form in the interaction region after secondary instability between a large-scale spanwisevortices and the inner boundary layer. Theinjection and sweeping process is observed. The power spectra of pressure indicating several frequency peaks associated with different flow structures is investigated.
-
Numerical Investigation on Ultra-High-lift Low-Pressure Turbine Cascade Aerodynamics at Low Reynolds Numbers Using Transition-Based Turbulence Models
Xiaole Wang,Bing Cui,Zuoli Xiao
DOI: https://doi.org/10.1080/14685248.2020.1849712
2021-01-01
Journal of Turbulence
Abstract:The performance of ultra-high-lift (UHL) low-pressure turbine (LPT) is subject to complex flow phenomena (e.g. separation, transition and reattachment) which require advanced modelling for accurate numerical predictions. The feasibility and fidelity of three widely used transition-based turbulence models are evaluated in the Reynolds-Averaged Navier-Stokes (RANS) prediction of low-Reynolds number flows in linear UHL LPT cascade (T106C). All three transition models prove to capture the tendency that the size of separation bubble decreases with the increase of Reynolds number or inlet turbulence intensity. It turns out that intermittency factor-transition momentum thickness Reynolds number based shear stress transport turbulence model is the most accurate among the three models, expect for the clean inlet case at an isentropic outlet Reynolds number of . It is suggested that different viscosity ratios should be prescribed at the inlet for various models to mimic the effect of turbulence intensities precisely. In order to take into account the periodic wakes in computation, a moving cylindrical bar is added to the cascade inlet. The assessment of the capability of three models in predicting unsteady wake induced transition is carried out for selected Reynolds numbers. Some practical suggestions are given for the use of transition models based on RANS equations in simulation of the ultra-high-lift LPT cascade flows at low Reynolds numbers.
-
Validation of correlations-based transition modeling strategies applied to the Spalart-Allmaras turbulence model for the computation of separation-induced transition
M. Bouchard,J. Marty,S. Deck,M. Costes
DOI: https://doi.org/10.1016/j.ast.2021.107045
IF: 5.457
2021-12-01
Aerospace Science and Technology
Abstract:Predicting the laminar-turbulent transition is becoming a necessity in order to reduce margin costs in the design of turbines and helicopter rotors. Most RANS models lack the capacity to create turbulence sufficiently abruptly to accurately predict separation-induced transition. This article aims at evaluating the performances of the γ−Reθ,t strategy applied to the Spalart-Allmaras and k−ω−SST models (ν˜−γ−Reθ,t and k−ω−γ−Reθ,t). The chosen test case features a laminar separation bubble over a flat plate. The results are compared to the flows obtained using classical algebraic criteria and validated against DNS data. The effects of the correction by Dacles-Mariani et al. are detailed as well as those of two sets of correlations. The turbulence production mechanism of the present models is too weak downstream of the first increase of intermittency, and the laminar separation bubbles are longer than in the reference flow. More specifically, the ν˜−γ−Reθ,t model with Medida and Baeder's correlations fails to reach the correct levels of turbulence production in the fully turbulent boundary layer. Switching the correlations corrects this last behavior. Finally, using maps of the activation zones of the Dacles-Mariani correction, a sensor is exhibited that could be used in future separation-induced transition modeling efforts.
engineering, aerospace
-
Laminar Transition over Airfoil: Numerical Simulation of Turbulence Models and Experiment Validation
Shuyue Wang,Gang Sun,Meng Wang,Xinyu Wang
DOI: https://doi.org/10.1007/978-981-13-3305-7_130
2019-01-01
Abstract:The article reviews the necessity of simulation in laminarization as an important optimization technique in aircraft design. Transition models e.g. k-ω SST with γ-Reθt model and k-kl-ω model are popular in industry and embedded in many optimization framework. The article aims to evaluate their accuracy in laminar transition predicting as well as in evaluating the effect of laminarization, i.e. the extended length of laminar brought by optimization in shape. The object for numerical simulation and experiment validation for laminar transition position predicting are one original airfoil and one laminarized airfoil under Re~2.62 × 106, Ma~0.785. The mesh with boundary conditions, the criterion for judging laminar transition, and the method to monitor laminar/turbulence distribution over model surface in wind tunnel experiment are introduced. The result shows that due to many factors, the two models cannot very accurately predict the laminar transition position, but the effect of laminarization can be evaluated quite satisfactorily by the k-ω SST with γ-Reθt model. Therefore, the laminarization applied on three-dimensional aircraft part, e.g. wing, nacelle can be constructed using this model in the future optimization framework of the authors.
-
On Steady State Computation of Turbulent Flows Using K–ε Models Approximated by the Time Splitting Method
T Du,ZN Wu,B Wang
DOI: https://doi.org/10.1002/fld.1119
IF: 1.847
2006-01-01
International Journal for Numerical Methods in Fluids
Abstract:The time splitting method is frequently used in numerical integration of flow equations with source terms since it allows almost independent programming for the source part. In this paper we will consider the question of convergence to steady state of the time splitting method applied to k-epsilon turbulence models. This analysis is derived from a properly defined scalar study and is carried out with success for the coupled k-epsilon equations. It is found that the time splitting method does not allow convergence to steady state for any choice of finite values of the time step. Numerical experiments for some typical turbulent compressible flow problems support the fact that the time splitting method is always nonconvergent, while its nonsplitting counterpart is convergent. Copyright (c) 2005 John Wiley & Sons, Ltd.
-
Simulation Of Transitional Flow On Low Pressure Turbine Blade With Unsteady Downstream Potential Interaction
Can Ma,Xin Yuan
DOI: https://doi.org/10.1115/GT2013-95208
2013-01-01
Abstract:This paper numerically investigates the transitional flow on a LPT(low pressure turbine) blade with fluctuating downstream potential field A linear T106 cascade is subjected to an oscillating potential field generated by downstream moving bars. Previous experimental results in open literature showed that the unsteady downstream Potential field has an obvious influence on the transitional boundary layer of LPT blade. For the numerical simulations in this paper, the unsteady Reynolds-Averaged Navier-Stokes equations are solved using the commercial software FLUENT The transition model used in this paper is the gamma-Re-theta model, which has been validated against a number of transitional flows previously, including the influence of upstream wakes on the transitional boundary layer of T106 turbine blade. The simulation results are first compared to the experimental results in open literature to validate the numerical methods. Two different FSTI(free stream turbulence intensity), 1.6% and 4.0% are investigated with axial spacing between the blade and the downstream bar varying from 50% axial chord to 25% axial chord. To investigate the influence of flow compressibility, two different inlet Mach numbers, 0.02 and 0.2 are simulated Results show that decreasing the axial spacing has an influence on the unsteady boundary layer separation and transition and the influence is enhanced at elevated inlet Mach number.