Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

High Efficiency Organic Solar Cells with Spray Coated Active Layers Comprised of A Low Band Gap Conjugated Polymer

Efficient Fully‐Sprayed Organic Solar Cells with Coffee‐Ring‐Free Photoactive Layer and Alloy Top‐Electrode

High Performance Solar Cell Based on Ultra-Thin Poly(3-Hexylthiophene): Fullerene Film Without Thermal and Solvent Annealing

Air-Knife-Assisted Spray Coating of Organic Solar Cells

Organic Photovoltaics Printed via Sheet Electrospray Enabled by Quadrupole Electrodes

Efficient Non-Fullerene Organic Photovoltaics Printed by Electrospray Via Solvent Engineering.

Thickness-Insensitive Anode Interface Layer for High-Efficiency Organic Solar Cells

Balancing the Molecular Aggregation and Vertical Phase Separation in the Polymer: Nonfullerene Blend Films Enables 13.09% Efficiency of Organic Solar Cells with Inkjet‐Printed Active Layer

Optimizing the Alkyl Side-Chain Design of a Wide Band-Gap Polymer Donor for Attaining Nonfullerene Organic Solar Cells with High Efficiency Using a Nonhalogenated Solvent

High Efficiency over 18.6% of Organic Solar Cells Enabled by PEDOT:PSS/Br-2PACz Dual-Anode Interface

High-Performance Organic Solar Modules Via Bilayer-Merged-Annealing Assisted Blade Coating

Air‐Processed Efficient Organic Solar Cells from Aromatic Hydrocarbon Solvent without Solvent Additive or Post‐Treatment: Insights into Solvent Effect on Morphology

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Nitrogen-Blowing Assisted Strategy for Fabricating Large-Area Organic Solar Modules with an Efficiency of 15.6%

Elimination of Drying‐Dependent Component Deviation Using a Composite Solvent Strategy Enables High‐Performance Inkjet‐Printed Organic Solar Cells with Efficiency Approaching 16%

Thickness Insensitive Organic Solar Cells with High Figure‐of‐Merit‐X Enabled by Simultaneous D/A Interpenetration and Stratification

High efficiency air-processed dithienogermole-based polymer solar cells

Volatilizable Solid Additive‐Assisted Treatment Enables Organic Solar Cells with Efficiency over 18.8% and Fill Factor Exceeding 80%

Toward all aerosol printing of high-efficiency organic solar cells using environmentally friendly solvents in ambient air

Vertically Optimized Phase Separation with Improved Exciton Diffusion Enables High-Efficiency Organic Solar Cells with Thick Active Layers

Bulk heterojunction organic photovoltaic cell fabricated by the electrospray deposition method using mixed organic solvent