Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Toward all aerosol printing of high-efficiency organic solar cells using environmentally friendly solvents in ambient air

Phase separation and domain crystallinity control enable open‐air‐printable highly efficient and sustainable organic photovoltaics

Organic Photovoltaics Printed via Sheet Electrospray Enabled by Quadrupole Electrodes

A guest-assisted molecular-organization approach for >17% efficiency organic solar cells using environmentally friendly solvents

Perovskite Solar Cells toward Eco-Friendly Printing

Elimination of Drying‐Dependent Component Deviation Using a Composite Solvent Strategy Enables High‐Performance Inkjet‐Printed Organic Solar Cells with Efficiency Approaching 16%

Efficient Non-Fullerene Organic Photovoltaics Printed by Electrospray Via Solvent Engineering.

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Efficient Fully‐Sprayed Organic Solar Cells with Coffee‐Ring‐Free Photoactive Layer and Alloy Top‐Electrode

Advances toward the Device Design and Printing Technology for Eco-friendly Organic Photovoltaics

Non-Halogenated Solvents Processed Efficient ITO-Free Flexible Organic Solar Cells with Upscaled Area

Efficient organic solar cells enabled by sustainable and synergetic device engineering

All green solvent and additive combination enables efficient non‐fullerene organic solar cells via sequentiao deposition strategy

High performance roll-to-roll printed PTB7-Th/PCBM solar cells (Conference Presentation)

Boosting Uniformity and Efficiency of Large‐Area Inverted Organic Photovoltaics Via ZnO Surface Energy Modulation

Solution-processed perovskite solar cells using environmentally friendly solvent system

Air‐Processed Efficient Organic Solar Cells from Aromatic Hydrocarbon Solvent without Solvent Additive or Post‐Treatment: Insights into Solvent Effect on Morphology

Overcoming Disordered Preaggregation in Liquid State for Highly Efficient Organic Solar Cells Printed from Nonhalogenated Solvents

Green‐Solvent‐Processed Organic Solar Cells with Approaching 20% Efficiency and Improved Photostability

Modulating the Growth of Nonfullerene Acceptors Toward Efficient and Stable Organic Solar Cells Processed by High‐Boiling‐Point Solvents

Eco-Friendly Solvent Engineered CsPbI2.77 Br0.23 Ink for Large-Area and Scalable High Performance Perovskite Solar Cells