Abstract:Flexible piezoelectric functional composite materials have the advantages of strong plasticity and good surface adhesion, and show great potential in smart wearable devices, electronic skin and other applications. However, due to the complexity of traditional preparation process, high molding cost and poor air permeability, its further development is limited. Direct ink writing (DIW) 3D printing technology is a rapid prototyping technology, with higher flexibility, faster manufacturing speed and lower manufacturing costs, is widely used in metal, ceramic and composite material molding. In this work, a ink system with polydimethylsiloxane (PDMS) as binder and barium titanate (BTO) ceramic powder as piezoelectric filler was developed, the printing work of flexible porous BTO/PDMS composite material was completed. DIW dual-nozzle printing technology was applied to realise "electrode-piezoelectric-electrode" integrated flexible porous functional gradient structure composites in this study. The results show that the BTO/PDMS ink has the characteristics of shear thinning. When the nozzle diameter is 0.5 mm, the printing speed is 650 mm/min, and the BTO mass fraction is 80%, the flexible porous piezoelectric composite with high precision and complex structure is printed. By phase analysis of BTO/PDMS, it is found that the sample has the characteristic peak of BTO. The microstructure analysis shows that the surface of the sample has good structural fidelity and there are a few island-like pores in the interior. The mechanical test shows that the maximum tensile strength of the sample is 1.33 MPa, the elastic modulus is 1.72 MPa, the longitudinal piezoelectric coefficient d 33 is 4.37 Pc/N, and the open circuit voltage VOC is 3.17 V. This work demonstrates an attractive method of moulding flexible piezoelectric materials with an "electrode-piezoelectric-electrode" structure, which provides a reference to current 3D printing flexible material fabrication techniques due to its simplicity of operation, time and manufacturing cost savings.

Fabrication and Characterization of Direct-Written 3D TiO 2 Woodpile Electromagnetic Bandgap Structures

Direct Writing of Three-Dimensional Woodpile BaTiO3 Structures

Direct Write Printing of Three-dimensional Photocatalytic TiO2 Structures

Direct Write Assembly of Three-dimensional PZT Woodpile Structure

Fabrication Of 3d Photocatalytic Alpha-Fe2o3 Structure Using Direct Ink Writing Method

Direct-write Assembly of Ceramic Three-dimensional Structures Based on Photosensitive Inks

Direct Write Assembly of 3-Dimensional Structures with Aqueous-Based Piezoelectric Inks

Fabrication of 3-Dimentional Photonic Band Gap Materials by Micromolding Method and Optical Properties Measurement

Fabrication and Characterization of Micropatterned Barium Titanate Ceramics

Direct Ink Writing of Special-Shaped Structures Based on Tio2 Inks

Creation of 3D Terahertz Photonic Crystals by the Direct Writing Technique with a TiO2 Sol-Gel Ink

Electrically Tunable Wafer-Sized Three-Dimensional Topological Insulator Thin Films Grown by Magnetron Sputtering

1D Magnetic Materials of Fe 3 O 4 and Fe with High Performance of Microwave Absorption Fabricated by Electrospinning Method

Direct ink writing of 3D piezoelectric ceramics with complex unsupported structures

Three-dimensional polydimethylsiloxane/barium titanate elastomer networks for piezoelectric energy harvesters

Fabrication and properties of BaTiO3 ceramics via digital light processing for piezoelectric energy harvesters

Direct Writing of Flexible Barium Titanate/Polydimethylsiloxane 3D Photonic Crystals with Mechanically Tunable Terahertz Properties

Customizing Three-Dimensional Elastic Barium Titanate Sponge for Intelligent Piezoelectric Sensing

Preparation of 3d Ceramic Meshes by Direct-Write Method and Modulation of Its Photocatalytic Properties by Structure Design

Study on the control of mechanical and electrical properties of 3d printed BTO/PDMS flexible porous composites

Rapid Fabrication of Three-Dimensional Woodpile Photonic Crystals by Means of Two-Photon Photopolymerization