Abstract:Ceramic photonic crystals have wide application potentials for THz technology due to their characteristic strong chemical stability and high temperature resistance for demanding environment. However, it is still a challenge to modulate the THz properties of as-prepared ceramic TPCs via post-creation treatments to satisfy different application requirements. In this work, the THz properties of rutile TiO2 ceramic 3D-TPCs were modulated by non-metal anion doping of either carbon or nitrogen, which was firstly created by the direct-writing technique with a TiO2 sol-gel ink followed by the high temperature sintering process at 1200 degrees C. Calcination of the pristine rutile TiO2 ceramic 3D-TPCs in either CO or NH3 atmosphere successfully doped either C or N dopants into rutile TiO2 ceramic 3D-TPCs, respectively, which changed their dielectric properties and subsequently induced different THz properties on these ceramic 3D-TPCs with the same structure. Their THz properties were found to be largely affected by the specific nature of the dopant. Compared with the pristine rutile TiO2 ceramic 3D-TPC, the bandgap positions of both C-doped and N-doped rutile TiO2 ceramic 3D-TPCs largely shifted toward the higher frequency, while the N-doped sample demonstrated a much broader bandgap. Thus, non-metal anion doping could be an effective post-creation approach to modulate the THz properties of ceramic TPCs.

Creation of 3D Terahertz Photonic Crystals by the Direct Writing Technique with a TiO2 Sol-Gel Ink

Direct Writing of Flexible Barium Titanate/Polydimethylsiloxane 3D Photonic Crystals with Mechanically Tunable Terahertz Properties

Direct-writing of Vanadium Dioxide/polydimethylsiloxane Three-Dimensional Photonic Crystals with Thermally Tunable Terahertz Properties

Rapid-Heating-Triggered in Situ Solid-State Transformation of Amorphous TiO2 Nanotubes into Well-Defined Anatase Nanocrystals

Printing of 3D photonic crystals in titania with complete bandgap across the visible spectrum

A Terahertz Photonic Crystal Wavelength Division Multiplexer Based on Graphene Surface Plasmon Polaritons

Modulation of Terahertz Properties of 3D Ceramic Photonic Crystals Via Post‐creation Non‐metal Anion Doping Treatment

High-quality photonic crystals with a nearly complete band gap obtained by direct inversion of woodpile templates with titanium dioxide

Mechanical Tuning of the Terahertz Photonic Bandgap of 3D-Printed One-Dimensional Photonic Crystals

Femtosecond Laser Direct Writing of TiO 2 Crystalline Patterns in Glass

Terahertz Circular Photonic Crystal Fiber

Fabrication and Characterization of Direct-Written 3D TiO 2 Woodpile Electromagnetic Bandgap Structures

Rapid Fabrication of Three-Dimensional Woodpile Photonic Crystals by Means of Two-Photon Photopolymerization

Terahertz-regime Realization and Optical Characterization of Two-Dimensional Photonic Crystal Waveguides on a Silicon-on-insulator (SOI) Substrate

Rapid fabrication of 2D and 3D photonic crystals and their inversed structures

A Naturally Grown Three-Dimensional Nonlinear Photonic Crystal

Fabrication of Three-Dimensional Micro-Structures with Two-Photon Absorption by Femtosecond Laser

Photothermal conversion of Ti2O3 film for tuning terahertz waves

Photonic Crystal Structures with Submicrometer Spatial Resolution Achieved by High-Power Femtosecond Laser-Induced Photopolymerization

Inlayed “Atom-Like Three-Dimensional Photonic Crystal Structures Created with Femtosecond Laser Microfabrication

Terahertz Rare-Earth Orthoferrite Metamaterials by 3-D Direct Writing Technology