Abstract:CuxAg1-xSbTe2 samples withx = 00.3 are prepared by a combined process of melt-quenching and spark plasma sintering (SPS). X-ray powder diffraction (XRD) analysis indicates that single phase samples with the NaCl-type structure are obtained for the Cu-doped samples before SPS treatment, whereas a small quantity of Ag2Te impurities coexist with the main cubic phase for the sample without Cu. According to our thermoanalysis and XRD results, the substitution of Cu for Ag can effectively prevent the precipitation of Ag2Te, but this also leads to the presence of a minor amorphous phase in the melt-quenched sample. The amorphous phase crystallizes into Sb7Te metastable phase at about 540 K, which finally transforms into the stable Sb2Te3 compound. After the SPS treatment of the melt-quenched sample, the sample withx=0.1 remains a single phase with the face-centered-cubic crystal structure, while Sb7Te and Sb2Te3 are precipitated as the second phases for the samples withx = 0.2 and 0.3, respectively. The electrical conductivity increases and the Seebeck coefficient decreases with the addition of Cu due to the existence of the second phase in the samples withx = 0.2 and 0.3. Accordingly, thermal conductivities also increase with the addition of Cu, leading to the reduced thermoelectric performance of thex= 0.2 and 0.3 samples. For the sample withx = 0.1, its power factor is comparable to that of the literature reported AgSbTe2 compound. As a result of so-called alloying effect, the phonon scattering effect is enhanced due to the partial replacement of Ag by Cu, leading to the reduced thermal conductivity of thex = 0.1 sample. Therefore, the Cu0.1Ag0.9SbTe2 sample exhibits the promising thermoelectric performance and a dimensionless thermoelectric figure of merit (ZT) value of 1 is achieved at 620 K.

Effect of Cu Concentration on Thermoelectric Properties of Nanostructured P-Type MgAg0.97−xCuxSb0.99

Evaluation of Thermoelectric Properties of Ag0.366Sb0.558Te

Enhanced Thermoelectric Performance of p-type AgSbTe2 via Cu Doping

Roles of concentration-dependent Cu doping behaviors on the thermoelectric properties of n-type Mg3Sb1.5Bi0.5

Thermoelectric performance improvement of p-type Mg3Sb2-based materials by Zn and Ag co-doping

Enhancing Thermoelectric Performance in P-type Mg3Sb2-based Zintls Through Optimization of Band Gap Structure and Nanostructuring

Effect of Cu2s Inclusion on the Thermoelectric Properties of N-Type Mg2sn1-Xyxsb0.03(Y= Si, Ge)

Study on Thermoelectric Performance by Na Doping in Nanostructured Mg1-xNaxAg0.97Sb0.99

Thermoelectric Properties of Ag-doped Compound: Mg3-xAgxSb2

Extraordinary Thermoelectric Performance in MgAgSb Alloy with Ultralow Thermal Conductivity

Synergistic modulation of electrical and thermal properties of Cu<sub>1.8</sub>S bulk materials via nanostructuring and band engineering

High thermoelectric performance of MgAgSb-based materials

Phase Stability, Crystal Structure and Thermoelectric Properties of Cu Doped AgSbTe2

Effect of Mg Content on Thermoelectric Property of Mg3(1+z)Sb2 Compounds

Na/Bi-co-doping and Heterogeneous Interfaces Leading to Enhanced Thermoelectric Performance of P-Type Mg3Sb2-based Zintls

Improving Thermoelectric Performance of AgSbTe2 through Suppression of Ag2Te and Band Convergence via Mg and Ti Codoping

Realizing Cd and Ag codoping in p-type Mg3Sb2 toward high thermoelectric performance

Strong anharmonicity induced low lattice thermal conductivity and high thermoelectric performance in (CuInTe<sub>2</sub>)<sub>1-</sub><i><sub>x</sub></i>(AgSbTe<sub>2</sub>) <i><sub>x</sub></i> system

Synergy of grain size and texture effect for high-performance Mg3Sb2-based thermoelectric materials

Tuning Ag content to achieve high thermoelectric properties of Bi-doped p-type Cu3SbSe4-based materials

Enhancing the Thermoelectric Performance of n‐Type Mg3Sb2‐Based Materials via Ag Doping