Abstract:BaTiO3 (BT) nanoparticles were prepared by the hydrothermal technique using different starting materials and the microstructure examined by XRD, SEM, TEM and HRTEM. X-ray diffraction and electron diffraction patterns showed that the nanoparticles were the cubic BaTiO3 phase. The BT nanoparticles prepared from the starting materials of as-prepared titanium hydroxide and barium hydroxide have spherical grain morphology, an average size of 65 nm and a fairly narrow size distribution. A uniform diffraction contrast across each single grain is observed in the TEM images, and the clear lattice fringes (with d(110) = 0.28 nm) observed in HRTEM images reveal that well-crystallized BT nanoparticles are synthesized by the hydrothermal method. The edges of the particles are very smooth, with no surface steps. BT nanoparticles with average grain size of 90 nm, synthesized using barium hydroxide and titanium dioxide as the starting materials, show surface facets. In this case a bimodal size distribution of large faceted and smaller particles is observed. Diffraction contrast variation across the particles caused by high strains within the particles is clearly observed. The high strains obviously stem from structural defects formed during hydrothermal synthesis, presumable in the form of lattice OH- ions and their compensation by cation vacancies. HRTEM images demonstrate that surface facets parallel to the (100) and (110) planes and small islands with 3 similar to 4 atomic layer thickness are frequently observed around the edge of the particles.

Influence of Raw Material Ratio of Ba/Ti on Fabrication of Nanocrystalline Batio3 Powder

Room-Temperature Synthesis of BaTiO<sub>3</sub>Nanoparticles in Large Batches

Effect of NaOH Concentration on Formation of Ba4Ti13O30 and BaTi5O11 Nanocrystals Prepared by Hydrothermal Method

Stoichiometry of BaTiO 3 nanoparticles

Synthesis and Characterization of BaTiO3 Nanopowders Via Solvothermal Method

Influence of Ph Value on Properties of Nanocrystalline BaTiO3 Powder

Preparation of Single-Crystalline BaTi5O11 Nanocrystals by Hydrothermal Method

Fabrication of Monodispersed 5‐nm BaTiO3 Nanocrystals with Narrow Size Distribution Via One‐Step Solvothermal Route

Ba 4 Ti 13 O 30 Nanocrystals Prepared by Hydrothermal Method

Phase Structure Of Nanocrystalline Batio3 Powders Via One-Step Solvothermal Route

Composition and shape control of single-crystalline Ba1-xSrxTiO3 (x=0-1) nanocrystals via a solvothermal route

Low-temperature Synthesis of TiB2 Nanocrystals Using TiO2 ,LiBH4 and Mg

Synthesis of Highly Dispersed Barium Titanate Nanoparticles by a Novel Solvothermal Method

Preparation for BaTiO3 Nano-crystalline Powder and Study on the Sintering Characteristics of Ceramic

Fabrication Of Textured Batio3 Ceramics

Synthesis of Nanocrystalline 0.94Bi<sub>0.5</sub>Na<sub>0.5</sub>TiO<sub>3</sub>-0.06BaTiO<sub>3</sub> Powder by a Citrate Method

Effect of raw material concentration on the morphology of nano-barium titanate ribbon-like fibers synthesized by hydrothermal

Synthesis of Nanocrystalline 0.94Bi(0.5)na(0.5)tio(3)-0.06Batio(3) Powder by A Citrate Method

Microstructural Characterization of BaTiO3 Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Preparation of Nanoscaled BaTiO3 Powders by DSS Method Near Room Temperature under Normal Pressure

Fabricating Uniform Tetragonal Barium Titanate Nanocrystals Via Sand Milling Assisted by an Innovative Two-Step Calcination