Abstract:BaTiO3 (BT) nanoparticles were prepared by the hydrothermal technique using different starting materials and the microstructure examined by XRD, SEM, TEM and HRTEM. X-ray diffraction and electron diffraction patterns showed that the nanoparticles were the cubic BaTiO3 phase. The BT nanoparticles prepared from the starting materials of as-prepared titanium hydroxide and barium hydroxide have spherical grain morphology, an average size of 65 nm and a fairly narrow size distribution. A uniform diffraction contrast across each single grain is observed in the TEM images, and the clear lattice fringes (with d(110) = 0.28 nm) observed in HRTEM images reveal that well-crystallized BT nanoparticles are synthesized by the hydrothermal method. The edges of the particles are very smooth, with no surface steps. BT nanoparticles with average grain size of 90 nm, synthesized using barium hydroxide and titanium dioxide as the starting materials, show surface facets. In this case a bimodal size distribution of large faceted and smaller particles is observed. Diffraction contrast variation across the particles caused by high strains within the particles is clearly observed. The high strains obviously stem from structural defects formed during hydrothermal synthesis, presumable in the form of lattice OH- ions and their compensation by cation vacancies. HRTEM images demonstrate that surface facets parallel to the (100) and (110) planes and small islands with 3 similar to 4 atomic layer thickness are frequently observed around the edge of the particles.

Fabrication Of Textured Batio3 Ceramics

A simple approach to porous low-temperature-sintering BaTiO 3

Fabrication Of Na0.5bi0.5tio3-Batio3-Textured Ceramics Templated By Plate-Like Na0.5bi0.5tio3 Particles

Fabrication and Electrical Properties of Textured Na 1/2 Bi 1/2 TiO 3 -Batio 3 Ceramics by Reactive-Templated Grain Growth

Fabrication of Na<sub>0.5</sub>Bi<sub>0.5</sub>TiO<sub>3</sub>-BaTiO<sub>3</sub>-Textured Ceramics Templated by Plate-Like Na<sub>0.5</sub>Bi<sub>0.5</sub>TiO<sub>3</sub>Particles

Dielectric Properties of BaTiO3 Based Ceramics Prepared from Nano-powders

Fabrication and Electrical Properties of Textured Ba(Zr0.2Ti0.8)O3–(Ba0.7Ca0.3)TiO3 Ceramics Using Plate-Like BaTiO3 Particles As Templates

Microstructural Characterization of BaTiO<sub>3</sub> Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Influence of Raw Material Ratio of Ba/Ti on Fabrication of Nanocrystalline Batio3 Powder

Preparation for BaTiO3 Nano-crystalline Powder and Study on the Sintering Characteristics of Ceramic

Fabrication and Characterization of Micropatterned Barium Titanate Ceramics

Textured Pb(Mg1/3nb2/3)O-3-Pbtio3 Ceramics By Templated Grain Growth

Microstructural Characterization of BaTiO3 Ceramic Nanoparticles Synthesized by the Hydrothermal Technique

Ba 4 Ti 13 O 30 Nanocrystals Prepared by Hydrothermal Method

Texture Development in Na<sub>1/2</sub>Bi<sub>1/2</sub>TiO<sub>3</sub>-BaTiO<sub>3</sub> Ceramics by Reactive-Templated Grain Growth

Texture Development in Na1/2bi1/2tio3-Batio3 Ceramics by Reactive-Templated Grain Growth

Preparation and Properties of BaTiO3 Ceramics from the Fine Ceramic Powder

Synthesis of High-Aspect-Ratio BaTiO3Platelets by Topochemical Conversion and Fabrication of Textured Pb(Mg1/3Nb2/3)O3-32.5PbTiO3Ceramics

Nanostructural and Physical Features of Batio3 Ceramics Prepared by Two-Step Sintering

Study On The Textured Bnkt Ceramics By Reactive Templated Grain Growth

Synthesis of Nanocrystalline 0.94Bi<sub>0.5</sub>Na<sub>0.5</sub>TiO<sub>3</sub>-0.06BaTiO<sub>3</sub> Powder by a Citrate Method