FE simulations of gas blow forming and prediction of forming limit diagram of AZ31 magnesium sheet

G. Zhou,K. Ananthaeswara,G. Mitukiewicz,D. Li,R.K. Mishra,M.K. Jain

DOI: https://doi.org/10.1016/j.jmatprotec.2014.11.014

IF: 6.3

2015-01-01

Journal of Materials Processing Technology

Abstract:•FLD determined from FE method.•Limit strains calculated from a strain acceleration criterion.•Predicted and measured FLDs compared for AZ31.

What problem does this paper attempt to address?

Simulation of Gas Bulging and Prediction of Forming Limit for AZ31 Magnesium Alloy Sheet

PENG Ying-hong

DOI: https://doi.org/10.3969/j.issn.1674-6457.2014.06.007

2014-01-01

Abstract:The finite element model for the experimental method of gas bulging at 300 ℃ was built for the AZ31 mag-nesium alloy sheet, and simulation analysis was conducted for the sheet bulging process. Based on the analysis of the strain history of the sheet, using the second-order principal strain turning point as the judgment criterion, the sheet forming limit strain was predicted. The deformation of specimens with different dimensions was analyzed and explained based on the com-parison of the simulation results with the experimental results.
Extrusion Limit Diagram Making for AZ31B Magnesium Alloy Tubes by FEM Simulation

WANG Xin,WANG Ying-xin,ZENG Xiao-qin,LU Chen

DOI: https://doi.org/10.3969/j.issn.1000-3940.2007.01.031

2007-01-01

Abstract:The true flow stress-true strain curves of AZ31 magnesium alloy are achieved by using Gleeble3000 thermo-simulator under various temperatures and strain rates.Then the true flow stress-strain curves are introduced into numerical simulation software.The extrusion processing of the Φ40mm×4mm AZ31B seamless tubes is simulated,based on which the extrusion limit diagram is made.The extrusion tests are performed in order to confirm the extrusion limit diagram,which proves the correctness of the extrusion limit diagram.
Simulation of Extrusion Process of AZ31 Magnesium Alloy

S. J. Liang,Z. Y. Liu,E. D. Wang

DOI: https://doi.org/10.1016/j.msea.2007.11.120

IF: 6.044

2008-01-01

Materials Science and Engineering A

Abstract:The extrusion process of AZ31 magnesium alloy has been simulated. First, a series of tests were designed to obtain the simulation parameters: stress–strain curves, friction factors and heat transfer coefficient. Then, a special extrusion process was carried out and simulated by DEFORM-2D simultaneously. The results reveal that the simulated temperature–time curve agrees well with the measured one, indicating the good accuracy of the simulation parameters. Accordingly, the extrusion of AZ31 at different conditions was analyzed in detail. The extrusion loads and temperature distribution of billets were obtained.
Forming Limits of Magnesium Alloy AZ31B Sheet at Elevated Temperatures

Zihan Li,Guowei Zhou,Dayong Li,Mukesh K. Jain,Yinghong Peng,Peidong Wu

DOI: https://doi.org/10.1016/j.ijplas.2020.102822

IF: 8.5

2020-01-01

International Journal of Plasticity

Abstract:Magnesium alloy sheets usually has to be processed by warm forming, and change of strain path and evolution of microstructure can significantly influence their warm formability. Forming limit test for an AZ31B alloy sheet under strain path changes was configured and implemented, and the effects of strain paths and microstructure evolution on the forming limit diagram are investigated. The sheet was pre-strained under in-plane uniaxial, plane strain and biaxial tension loading paths at 150 degrees C, 200 degrees C and 300 degrees C, followed by hemispherical punch stretching experiments at the three temperatures using specimens extracted from the pre-strained samples. A crystal plasticity model that incorporates dynamic recrystallization (DRX) and annealing recovery was combined with the Marciniak-Kuczyliski (M-K) approach to calculate the FLDs. The evolution of dislocation density during annealing in the pre-strained FLD test at 200 degrees C was evaluated, through which the predictions of pre-strained FLDs were considerably improved. The present work provides experimental as well as crystal plasticity based methods for evaluating warm formability of magnesium alloys influenced by temperature, pre-straining, DRX and recovery.
Finite element simulations and experimental verifications for forming limit curve determination of two-layer aluminum/brass sheets considering the incremental forming process

A. Jalali,R. Hashemi,M. Rajabi,P. Tayebi

DOI: https://doi.org/10.1177/14644207211045212

2021-10-12

Abstract:In this paper, forming limit diagram (FLD) of aluminum/brass two-layer sheets through an incremental forming process (ISF) was studied numerically and experimentally. At first, the two-layer aluminum 1050/brass (65% copper) sheets were fabricated using the roll bonding process. Also, the finite element simulations of the incremental forming process with ABAQUS software were utilized to predict the FLD. For this purpose, the criterion of the second derivative of the equivalent plastic strain was used to predict fracture. Finally, the numerical simulation results were compared with the experimental results. For instance, comparing experimental and numerical FLD 0 values for the formed samples with forming angle 62.5-degree showed a 7% difference. However, the difference was negligible, and numerical simulation results could be used with an appropriate reliability coefficient. The effect of sheet arrangement towards tools was then investigated. It finds out from the experimental results that the formability of the Brass/Al (brass was up layer and aluminum was bottom layer) was more than the Al/Brass (aluminum is up layer and brass is bottom layer). In the following, the ISF parameters such as forming limit angle, step-down, and thickness distribution were investigated.

materials science, multidisciplinary
Forming Limit Diagram Analysis Based on Crystal Plasticity for Magnesium Alloy Sheets

Weiqin Tang,Dayong Li,Yinghong Peng,Shaorui Zhang

DOI: https://doi.org/10.1063/1.4806951

2013-01-01

AIP Conference Proceedings

Abstract:In the sheet metal forming industry, forming limit diagram (FLD) is a useful tool for quantifying metals formability. However, the experimental measurement of FLD is difficulty, time consuming and expensive process. It would be useful if FLD calculated with a theoretical model could replace experimental measurements. In this research, a rate independent crystal plasticity model is developed to analyze the plastic deformation of hexagonal close packed (HCP) materials by incorporating the crystallography of deformation twinning in plasticity model. The numerical simulations of FLD for AZ31 magnesium alloy are performed based on the crystal plasticity model incorporated within the Marciniak-Kuczynski (M-K) approach. The approach allows for the incorporation of initial texture, evolution of texture, and texture-induced anisotropy. The effects of mechanical twinning on plastic deformation and FLD behavior for AZ31 alloy are also incorporated. Finally, the calculation of the FLD for AZ31 alloy successfully predicts the experimental tendency that phenomenological plasticity model cannot reproduce.
Standard and Strain Path Change Forming Limit Diagrams of AZ31B Magnesium Sheet at Elevated Temperatures

Guowei Zhou,Mukesh K. Jain,D. Li,R. S. Mishra

DOI: https://doi.org/10.1088/1757-899x/418/1/012032

2018-01-01

Abstract:Effect of strain path change on formability and microstructural characteristics of AZ31B automotive magnesium sheet material is studied at 300°C. The standard forming tests are carried out using Nakazima tests within the environmental chamber. The strain path change tests are performed by in-plane uniaxial, plane strain and balanced biaxial pre-strained specimens in the first stage and Nakazima test in the second stage. The enhancement in the activity of prismatic and pyramidal slip as well as a reduction in material anisotropy with increase in temperature is responsible for improvements in formability. Compared to the standard FLD, all uniaxial, plane strain, and balanced biaxial pre-strained materials exhibit higher limit strains. This rise in FLD also incorporates the effect of additional annealing during temperature rise period prior to testing which cannot be avoided with the present experimental set-up and test methodology. The pre-strain effect is reduced by additional annealing effect caused by elevated temperature soaking time. At 300°C, the pre-strained material is almost fully recovered and behaves as the as-received material. Also, significant dynamic recrystallization is observed at 300°C.
Local Hot Gas Forming of Long Axis Bellow with Non-uniform Temperature

Zhu Shiqiang,Wang Kehuan,Wei Wenting,Liu Gang

2021-01-01

Rare Metal Materials and Engineering

Abstract:A novel local hot gas forming (LHGF) process with non-uniform temperature field was proposed to form AZ31 magnesium alloy long axis bellow. Hot uniaxial tensile tests at temperatures ranging from 573 K to 673 K and strain rates ranging from 0.001 s(-1) to 0.1 s(-1) were carried out to study the hot deformation behavior of AZ31 magnesium alloy. Forming apparatuses with independent heating and cooling facilities were developed to achieve the non-uniform temperature field. Local hot gas forming tests of single wave bellow were performed to study the effects of temperature and gas pressure on the forming process and to determine the proper processing windows. A long axis bellow with 5 waves was finally formed to validate the novel process. Results show that the maximum temperature in the cooling zone can be kept below 50 degrees C and the temperature in the heating zone can be accurately controlled with fluctuation less than +/- 5 degrees C. A qualified AZ31 magnesium alloy long axis bellow with 5 waves is formed with small dies at 623 K under a constant gas pressure of 14 MPa. The average grain size at the wave crest is refined from 21.8 gm in the initial to 16.56 mu m after forming due to the dynamic recrystallization during the forming.
Development and validation of an extrusion limit diagram for AZ31 magnesium alloy

Ying Wang,Xiaoqin Zeng,Wenjiang Ding,Alan A. Luo,Anil K. Sachdev

2006-01-01

Abstract:Extrusion limit diagrams can be used to optimize the extrusion process by maximizing the extrusion productivity while maintaining the best metallurgical quality of the extruded products. In this report, flow stress data from hot compression tests were used to develop an extrusion limit diagram for AZ31 magnesium tubes. The extrusion limit diagram shows a wide region available for extruding AZ31 seamless tubes. Actual extrusion trials validated the predicted temperature rise limit curve corresponding to the occurrence of surface cracking during the extrusion process. Magnesium tubes from this alloy were successfully extruded according to the safe regions identified by the extrusion limit diagram determined from simple compression tests.
Determination and Application of Forming Limit Diagram of Aluminium Alloy 5083 Sheet

Gang Fang,Jia-Qing Zhao,Qian Wang

DOI: https://doi.org/10.1088/1757-899x/418/1/012054

2018-01-01

Abstract:The present research was aimed to evaluate the formability of aluminium alloy 50830-O sheet. Two-dimensional DIC method was used to measure the strain field of uniaxial tensile specimens. The flow stress equation was obtained on the base of these measured strain and stress data. The influence of virtual gauge on strain measurement was analysed. The hemispherical punch tests were conducted, where three-dimensional DIC was used to measure the strains on the forming regions of aluminium sheets. The FLD of aluminium alloy 5083-O was established using these measured strain data. The data derived from the tests were applied in FE simulations of the inner panel of a car body. Comparison between the results of the experiments and the simulations showed that the necking and fracture of the aluminium alloy component during stamping could be accurately predicted.
Constitutive Model Development and the Numerical Study on the Drawability of AZ31 Sheet

YH Peng,YB Luo,DY Li,JL Yin

DOI: https://doi.org/10.4028/www.scientific.net/msf.488-489.645

2005-01-01

Materials Science Forum

Abstract:To examine the formability of a magnesium-based alloy AZ31 sheet, a temperature and strain rate related constitutive model for AZ31 sheet was developed based on tensile experiments. The relative parameters were obtained by fitting the equation to the experimental data. The comparison between the fitted and the experimental data proved the effectiveness of the model. Based on this model, the deep drawing process has been simulated with the finite element method and the limit drawing ratio (LDR) of AZ31 sheet was numerically studied. The study result was helpful to the application of the stamping technology for the magnesium alloy sheet.
Numerical Investigation into the Effect of Uniaxial and Biaxial Pre‐Strain on Forming Limit Diagram of 5083 Aluminum Alloy

F. Zhalehfar,A. Gorji,S. J. Hosseinipour,S. Nourouzi

DOI: https://doi.org/10.1063/1.3623607

2011-08-29

Abstract:In this paper, numerical simulations are carried out to determine the forming limit diagram (FLD) of 5083 aluminum alloy. The aim is to predict the effect of strain path change on the forming limit curve (FLC) of this alloy. For this purpose, out-of-plane formability test method with hemispherical punch was simulated by using commercial finite element software, ABAQUSE 6.9. In the first stage, square blanks were modeled and then some of them were pre-strained uniaxially by tension test and some others were pre-strained biaxially by stretching over the hemispherical punch. In the second stage, the formability test specimens’ models were prepared by trimming the pre-strained blanks with the longitudinal axis parallel and perpendicular to the rolling direction. For trimming, a program was written in MATLAB 7.6 which could determine the new elements and introduce their properties to the FEM model. Ductile fracture criteria were used to predict failure. Furthermore, forming limit stress diagram (FLSD) was determined. The numerical results were compared with the experimental findings. Uniaxial pre-straining increased and shifted the FLC to the left hand side of the diagram for both parallel and perpendicular to the rolling direction. Biaxial pre-straining shifted the FLC to the right hand side of the diagram for both directions, and also decreased the FLC for the specimens parallel to the rolling direction.

Materials Science,Engineering
Development of a high-temperature double-layer bulge test for failure prediction in gas-based hot forming of a high-strength aluminium alloy

T Teeuwen,N K Baru,K J Tilly,D Bailly,G Hirt

DOI: https://doi.org/10.1088/1757-899x/1238/1/012049

2022-06-01

IOP Conference Series: Materials Science and Engineering

Abstract:In order to meet the continuously increasing environmental concerns, automotive lightweight concepts of replacing steels with high strength aluminium alloys are one promising solution. Therefore, complex automotive structural components manufactured with new processes like rapid gas-based hot sheet metal forming can become a key factor from a forming technology point of view. A product and process development phase, which is mainly assisted by numerical simulations, mandates knowledge of the material forming limits under the process conditions. The aim of this work is to determine the FLD of a 6xxx precipitation-hardening aluminium alloy within the solution heat treatment temperature range under gas-based hot forming process conditions. For this purpose, a hydraulic double-layered bulge test, as introduced by Banabic, is used as the basis and a high-temperature test setup as well as a characterization methodology are established. FE simulations are utilized to optimize the specimen geometries aiming at specific strain paths. Experiments are conducted with the optimized specimen geometries and the high-temperature FLD is extracted. The FLD is further used in simulations for process parameter identification for failure-free gas-based hot forming of a laboratory scale benchmark component. Experimental validations showed the reliability of the methodology and the determined FLD for failure prediction in the novel forming process.
Prediction of FLD for sheet metal by considering through-thickness shear stresses

Ahmad Ghazanfari,Seyed Soroush Soleimani,Mansour Keshavarzzadeh,Mostafa Habibi,Ahmad Assempuor,Ramin Hashemi

DOI: https://doi.org/10.1080/15397734.2019.1662310

2019-09-09

Mechanics Based Design of Structures and Machines

Abstract:In this study, the effect of through-thickness shear (TTS) stress has been examined on the prediction of forming limit diagrams (FLDs). Determination of the FLD is based on the Marciniak–Kuczynski (M–K) model with some modifications on the stress states for consideration of the TTS stress effects. For solving the equations, the Newton–Raphson method has been used. Furthermore, the Nakazima test has been simulated to investigate the stress state which occurs in the sheet during the test. Results showed that the formability of sheet metal could be better as the through-thickness stress increased. Also, implementation of TTS stress in the present model, the corresponding FLD has better agreement than the conventional FLD with the experimental test result.
Development And Validation Of Extrusion Limit Diagram For Az31 And Am30 Magnesium Alloys

Yingxin Wang,Xiaoqin Zeng,Wenjiang Ding,Alan A. Luo,Anil K. Sachdev

DOI: https://doi.org/10.4028/www.scientific.net/MSF.546-549.327

2007-01-01

Abstract:Uniaxial hot compression tests were performed at constant temperature (T) and strain rate (epsilon) in the ranges of 200-500 degrees C at an interval of 50 degrees C and 0.001-20 s(-1). The flow stress data were used to develop the extrusion limit diagram for AZ31 and AM30 magnesium tubes. The extrusion limit diagram shows a wide region available for extruding AZ31 and AM30 seamless tubes, and comparison of the two extrusion limit diagrams shows that, the extrudability of AM30 alloy is better than that of AZ31 alloy. Actual extrusion trials validated the predicted temperature rise limit curve corresponding to the occurrence of surface cracking during the extrusion process. Magnesium tubes were successfully extruded according to the safe regions identified by the extrusion limit diagram.
Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

Fei-Fan Li,Gang Fang,Ling-Yun Qian

DOI: https://doi.org/10.1177/1056789519855763

IF: 3.988

2019-01-01

International Journal of Damage Mechanics

Abstract:This work was aimed to experimentally and theoretically investigate the formability of a new magnesium alloy sheet at room temperature. The fracture forming limit diagram was predicted by MMC3 and DF2014 models, where the non-linear strain path effect was taken into account by means of damage accumulation law. In order to obtain the instantaneous values of the stress triaxiality and the Lode parameter during the deformation process, strains tracked by digital image correlation technique were transformed into stresses based on the constitutive equations. The fracture forming limit diagram predicted by the fracture models was compared with the forming limits obtained by ball punch deformation tests. The prediction errors were evaluated by the accumulative damage values, which verified the advantages of ductile fracture models in predicting the forming limits of the magnesium alloy sheets.
Simulation and Experimental Investigation of Friction Stir Welded Wrought Magnesium Alloy AZ31B

Pradeep K. Yadav,Manoj K. Khurana,Ravindra Kumar

DOI: https://doi.org/10.1007/s11665-024-10159-5

IF: 2.3

2024-10-01

Journal of Materials Engineering and Performance

Abstract:In this study, a finite element (FE) model was developed using the ANSYS software package to simulate the thermal behavior of a magnesium-based alloy during friction stir welding (FSW). The FE model was based upon a moving heat source, which was influenced by process parameters such as tool rotational speed, welding speed, shoulder diameter, and pin geometry. It was observed that the temperature increased with rotational speed and shoulder diameter but decreased with welding speed. The predicted maximum temperature distribution obtained from the FE model was validated by conducting experiments and using thermocouples to measure the actual temperatures. The absolute error percentage between the predicted and experimental values was less than 8%, indicating good agreement between the model predictions and the experimental data. The welded samples were tested for tensile strength, microhardness and impact strength. The maximum values obtained were 163.3 MPa for tensile strength, 4.1 KJ for impact strength, and 82 Hv for microhardness. Microstructural analysis revealed finer grains in the stir zone when using a welding speed of 150 mm/min, rotational speed of 900 rpm, and shoulder diameter of 19 mm. These parameters led to improved grain refinement in the welded region. Fractured surfaces from tensile tests were examined, and it was observed that the fracture initiation occurred in the thermomechanical affected zone of the advancing side.

materials science, multidisciplinary
Evaluation of Seven Ductile Fracture Criteria for Failure Prediction of AZ31 Sheet in Warm Forming

jian guang liu,wei liu

DOI: https://doi.org/10.4028/www.scientific.net/AMR.482-484.1947

2012-01-01

Abstract:Seven commonly used ductile fracture criteria are briefly reviewed and the validity of predicting the failure of AZ31 Mg alloy sheet by using these ductile fracture criteria is evaluated. Through fitting the experimental FLCs, the damage parameters for these ductile fracture criteria are determined firstly. Integrating these seven ductile fracture criteria into Abaqus/Explicit via VUMAT subroutine, the warm deep drawing process of AZ31 Mg alloy sheet is simulated. The limit drawing ratios (LDR) of AZ31 Mg alloy sheet at different temperature are predicted. The comparison of predictions with the experimental results has shown that the combination of the finite element simulation and the ductile fracture criterion is useful for predicting the fracture occurred in warm deepdrawing of AZ31 Mg alloy sheet.
Predicting the Warm Forming Behavior of We43 and Aa5086 Alloys

Ishwar Kapoor,R. Ganesh Narayanan,Scott Taylor,Vit Janik,Richard Dashwood

DOI: https://doi.org/10.1016/j.proeng.2016.12.136

2017-01-01

Abstract:In the present work, we have studied the formability behaviour of two types of magnesium alloys, WE43 hot rolled and WE43 cold rolled by carrying out uniaxial tensile test at elevated temperatures of 350°C to 500°C both experimentally and numerically at a constant strain rate of 10-3s-1. Finite element (FE) model is simulated in ABAQUS/CAE 6.7-6 using coupled temperature-displacement step at higher temperature considering material's property to be isotropic in nature. The effect of temperature on maximum flow stress and major strain at onset of necking is discussed. The true stress-strain behaviour and necking evolution through strain mapping are predicted from FE model and compared with the experimental results. The results show that with increase in temperature, the maximum flow stress decreases and necking delays with increase in limiting major strain for the Magnesium alloys. The work has been extended to predict the forming limit strains of Al 5086 alloy only on the negative minor strain region using M-K (Marciniak and Kuczynski) concept. An FE model based on M-K concept is simulated at 20°C, 150°C and 200°C using coupled temperature-displacement step considering anisotropic sheet material. A groove is created in the middle of the model with an optimizedf value of 0.99, after much iteration. The forming limit strains from such FE simulations are compared with the available experimental data. The results are encouraging providing scope for further improvements in modelling.
FINITE ELEMENT ANALYSIS OF FORMING LIMITS FOR STRETCH FORMING OF PERFORATED ALUMINIUM SHEET METALS

G. Venkatachalam,S. Narayanan,V. Kumar

Abstract:Stretch forming is one of the sheet metal forming process in which sheets are stretched to get the required shape. Formability of sheet metal is its ability to form when it is subjected to cold working process. Formability of a sheet metal is measured by Forming Limit Diagram (FLD/FLC). The limiting or failure strains in sheet metal forming are best represented by a forming limit curve which indicates the onset of necking over all possible combinations of strains in the plane. An attempt is made here to simulate the stretch forming of perforated sheet metals thereby studying its limiting strain. The uniaxial stretching and biaxial stretching are performed to get forming limit diagram. The influence of open area, and hole shape on FLD are studied. Perforated sheet is modelled with finite element method by using commercial FEA software ANSYS to calculate the major strain, minor strain and failure load for both uniaxial stretching and biaxial stretching of perforated sheet metal. It has been found that increasing in open area reduces the limiting major and minor strain. It has also been studied the influence of hole shape and punch shape on limiting major and minor strain.

Engineering,Materials Science

FE simulations of gas blow forming and prediction of forming limit diagram of AZ31 magnesium sheet

Simulation of Gas Bulging and Prediction of Forming Limit for AZ31 Magnesium Alloy Sheet

Extrusion Limit Diagram Making for AZ31B Magnesium Alloy Tubes by FEM Simulation

Simulation of Extrusion Process of AZ31 Magnesium Alloy

Forming Limits of Magnesium Alloy AZ31B Sheet at Elevated Temperatures

Finite element simulations and experimental verifications for forming limit curve determination of two-layer aluminum/brass sheets considering the incremental forming process

Forming Limit Diagram Analysis Based on Crystal Plasticity for Magnesium Alloy Sheets

Standard and Strain Path Change Forming Limit Diagrams of AZ31B Magnesium Sheet at Elevated Temperatures

Local Hot Gas Forming of Long Axis Bellow with Non-uniform Temperature

Development and validation of an extrusion limit diagram for AZ31 magnesium alloy

Determination and Application of Forming Limit Diagram of Aluminium Alloy 5083 Sheet

Constitutive Model Development and the Numerical Study on the Drawability of AZ31 Sheet

Numerical Investigation into the Effect of Uniaxial and Biaxial Pre‐Strain on Forming Limit Diagram of 5083 Aluminum Alloy

Development of a high-temperature double-layer bulge test for failure prediction in gas-based hot forming of a high-strength aluminium alloy

Prediction of FLD for sheet metal by considering through-thickness shear stresses

Development And Validation Of Extrusion Limit Diagram For Az31 And Am30 Magnesium Alloys

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

Simulation and Experimental Investigation of Friction Stir Welded Wrought Magnesium Alloy AZ31B

Evaluation of Seven Ductile Fracture Criteria for Failure Prediction of AZ31 Sheet in Warm Forming

Predicting the Warm Forming Behavior of We43 and Aa5086 Alloys

FINITE ELEMENT ANALYSIS OF FORMING LIMITS FOR STRETCH FORMING OF PERFORATED ALUMINIUM SHEET METALS