Abstract:Magnesium sheet metal alloys have a hexagonal close packed (hcp) crystal structure that leads to severe evolving anisotropy and tension-compression asymmetry as a result of the activation of different deformation mechanisms (slip and twinning) that are extremely challenging to model numerically. The low density of magnesium alloys and their high specific strength relative to steel and aluminum alloys make them promising candidates for automotive light-weighting but standard phenomenological plasticity models cannot adequately capture the complex plastic response of these materials. In this study, the constitutive plastic behavior of a rare-earth magnesium alloy sheet, ZEK100 (O-temper), was considered at room temperature, under quasi-static conditions. The CPB06 yield criterion for hcp materials was employed along with a non-associative flow rule in which the yield function and plastic potential were calibrated for a range of plastic deformation levels to account for evolving anisotropy under proportional loading. The non-associative flow rule has not previously been applied to magnesium alloys which require the use of flexible constitutive models to capture the severe anisotropy and its evolution with plastic deformation. The non-associative flow rule can provide the required flexibility by decoupling the yield function and plastic potential. For the associative flow rule, such flexibility can only be achieved by multiple linear transformations of the stress tensor resulting in expensive models for calibration and simulations. The constitutive model was implemented as a user material subroutine (UMAT) within the commercial finite element software, LS-DYNA, for general 3-D stress states along with an interpolation technique to consider the evolution of anisotropy based upon the plastic work. To evaluate the accuracy of the implemented model, predictions of a single-element model were compared with the experimental results in terms of flow stresses and plastic flow directions under various proportional loading conditions and along different test directions. Finally, to assess the predictive capabilities of the model, full-scale simulations of coupon-level formability experiments were performed and compared with experimental results in terms of far-field load-displacement and local strain paths. Using these experiments, the constitutive model was evaluated across the full range of representative stress states for sheet metal forming operations. It was shown that the predictions of the model were in very good agreement with experimental data.

Forming Limit Diagram Analysis Based on Crystal Plasticity for Magnesium Alloy Sheets

Analytical Method for Forming Limit Diagram Prediction with Application to a Magnesium ZEK100-O Alloy

Simulation of Magnesium Alloy AZ31 Sheet During Cylindrical Cup Drawing with Rate Independent Crystal Plasticity Finite Element Method

A Crystalline Plasticity Finite Element Method for Simulation of the Plastic Deformation of Az31 Magnesium Alloys

Dynamic plasticity of AZ31 magnesium alloy: Experimental investigation and constitutive modeling

Forming Limit Analysis of Mg-2Zn-1.2Al-0.2Ca-0.2RE Alloy Sheet Using Ductile Fracture Models

Numerical simulation of plastic behavior and meso inhomogeneous deformation in AZ31 Mg alloy

Constitutive Modeling of Slip, Twinning and Detwinning for Mg Alloy and Inhomogeneous Evolution of Microstructure

The Polycrystalline Plasticity Due to Slip and Twinning During Magnesium Alloy Forming

Multi-scale Modelling of Evolving Plastic Anisotropy During Al-alloy Sheet Forming

Forming Limit Diagram Prediction of Magnesium Alloy Sheet at Warm Condition

Forming Limits of Magnesium Alloy AZ31B Sheet at Elevated Temperatures

Plastic Flow Characteristics and Physical Conception Constitutive Relation for AZ31 Cast Magnesium Alloy

Experiment Research on the Forming Limit Diagrams(FLD)of Magnesium Alloy Sheet

Application of an Evolving Non-Associative Anisotropic-Asymmetric Plasticity Model for a Rare-Earth Magnesium Alloy

Deformation Analysis of Magnesium Alloy Based on Crystal Plasticity Theory

Simulation of Cylindrical Cup Drawing of Az31 Sheet Metal with Crystal Plasticity Finite Element Method

A Dislocation Density Based Crystal Plasticity Model of 3D Complex Sheet Metal Forming

Simulation of the Extrusion Texture of Magnesium Alloy AZ31 Using Crystal Plasticity Finite Element Method

Forming Limit Analysis of BCC Sheet Metal by Using Crystalline Plasticity Model

The Forming Limit Prediction Using a Rate-Dependent Crystal Plasticity Model