Flame propagation through zirconium particles coated with different ratios of Fe 3 O 4

wei gao,qi zhou,jinhua sun

DOI: https://doi.org/10.1016/j.fuel.2015.01.082

IF: 7.4

2015-01-01

Fuel

Abstract:•Flame propagated more quickly in zirconium particles coated with an Fe3O4 ratio of 9:1.•The temperature of zirconium particles coated with an Fe3O4 ratio of 9:1 was higher.•A replacement reaction occurred between Zr and Fe3O4.

What problem does this paper attempt to address?

Flame Propagation Characteristic of Zirconium Particle and Zirconium Particle Coated with Fe3O4

周琪,孙金华,王秋红,尹艺,徐耀,吕宝亮

2012-01-01

Abstract:In this paper, the flame propagation characteristic of the cloud of pure zirconium particle and zirconium particle coated with Fe3O4 was investigated in a square-open tube. According to the results of TG analysis,the weight increase of zirconium particle coated with Fe3O4 is obviously less than that of pure zirconium particle. A high-speed video camera was used to record the images of flame propagation,with which the velocity of flame propagation was calculated. It was obtained that the propagation velocity of zirconium particle coated with Fe3O4 is less than that of pure zirconium particle. The results also demonstrated that their flame propagation velocities are both oscillatory at low concentration(0.454,kg/m3)and steadily increase at high concentration(0.842,kg/m3). Micro-thermocouples were used to obtain temperature profiles,and the temperature rise of zirconium particle coated with Fe3O4 lagged behind that of pure zirconium particle. XPS was used to analyze the combustion products of zirconium particle coated with Fe3O4,and the peak value of Fe was 709.99,which indicated that the replacement reaction of Fe3O4 by zirconium may occur in the flame propagation of zirconium particle coated with Fe3O4.
Flame Propagation Characteristics and Combustion Mechanism of FeOOH-coated Zirconium Particles

Qiuhong Wang,Jun Deng,Jinhua Sun,Chi-Min Shu,Zhenmin Luo,Bo Liu

DOI: https://doi.org/10.1007/s10973-016-5545-0

IF: 4.755

2016-01-01

Journal of Thermal Analysis and Calorimetry

Abstract:Zirconium (Zr) particles are coated with ferric oxyhydroxide (FeOOH) nanoparticles to form a core–shell structure, and this process alters the combustion performance of the zirconium particles. This study explored the flame propagation characteristics and combustion mechanism of FeOOH-coated zirconium particles. A high-speed observation system was used to reveal the flame propagation velocities and temperatures, and scanning electron microscopy, thermogravimetry (TG), and X-ray diffraction were used to examine and elucidate the combustion mechanism of FeOOH-coated zirconium particles. The results showed that when the concentration was increased, the flame propagation velocities of pure zirconium dust cloud were higher than those of FeOOH-coated zirconium dust cloud with the molar ratio of 1:6, which in turn were higher than the molar ratio of 1:3 due to the zirconium content. With increasing the concentration from 0.313 to 0.938 kg m−3, the temperatures of FeOOH-coated zirconium dust cloud with the molar ratio of 1:6 and 1:3 both were no peak. Moreover, the temperatures of FeOOH-coated zirconium dust cloud with the molar ratio of 1:6 were always higher than those with the molar ratio of 1:3. There were three phases of mass loss FeOOH-coated zirconium particles by TG test. The first phase of mass loss was because of evaporation of the FeOOH-coated zirconium particles, and the second phase of mass loss was the generation of Fe2O3 because of dehydroxylation of FeOOH. The third phase of mass loss was the residual of thermal decomposition due to Fe3O4 being formed from Fe2O3. It was also concluded that a replacement reaction occurred between Zr and Fe2O3 in the combustion process, and pure Fe is oxidized to Fe3O4 at high temperatures.
Combustion Characteristics of Zirconium Particles Coated with Ferrite Nanoparticles

Qiuhong Wang,Zhongyi Shen,Jinhua Sun,Chi-Min Shu,Juncheng Jiang,Jun Deng,Youjie Sheng,Bin Laiwang

DOI: https://doi.org/10.1016/j.powtec.2021.04.097

IF: 5.64

2021-01-01

Powder Technology

Abstract:To improve the properties of Zr powder for specific applications in aerospace and military fields, Zr powders were coated with ferrite nanoparticles, namely FeOOH, Fe2O3, and Fe3O4. An instantaneous flame propagation system and scanning electron microscopy, X-ray diffraction, thermogravimetry, and differential scanning calorimetry techniques was used to characterized the flame propagation characteristics, micromorphology, phase composition, crystal structure, thermal stability, and reactivity of the three types of nano ferrite-coated Zr particles. The results showed that, the flame propagation velocity and maximal temperature exhibited the following order: Fe2O3-coated > FeOOH-coated > Fe3O4-coated Zr dust cloud. With an increase in the proportion of coating materials, the combustion characteristics all decreased. The contrastive analysis of surface, ingredient and heating process revealed that, during combustion, in addition to inducing oxidation–reduction, inner Zr led to a replacement reaction with the outside ferrite coating layer, and then, Fe generated was oxidized at a high temperature.
Combustion Behaviour of Fe 2 O 3 -coated Zirconium Particles in Air

qiuhong wang,jinhua sun,jun deng,hu wen,yao xu

DOI: https://doi.org/10.1016/j.egypro.2015.02.053

2015-01-01

Energy Procedia

Abstract:Zirconium metal powder is widely used in aerospace and military as a metal fuel because of its high combustion rate and heat. This powder is used to produce flash powder, fireworks, artillery shells, timing bomb fuses and solid propellant rocket fuel. To comply with the special requirements for aerospace and military applications, zirconium particles are coated with Fe2O3 ferrite magnetite nanoparticles to form a core-shell structure. This process alters the combustion performance of the coated zirconium dust. In this study, the combustion behaviour of Fe2O3-coated zirconium particles in the air is explored. Scanning electron microscopy, X-ray diffraction, thermogravimetry and differential scanning calorimetry are used to examine the micromorphology, phase composition, crystal structure, thermal stability and reactivity of Fe2O3-coated zirconium particles. The combustion behaviour is presented, with the coating layer of Fe2O3-coated zirconium particles generating a replacement reaction with the inner core zirconium. The inner zirconium induced an oxidation-reduction reaction with oxygen and pure Fe was oxidised at high temperatures. The decomposition reaction was due to the residue of Fe2O3 that did not react with zirconium.
Experimental study on flames propagating through zirconium particle clouds.

Yi Yin,Jinhua Sun,Yibin Ding,Song Guo,Xuechao He

DOI: https://doi.org/10.1016/j.jhazmat.2009.04.098

IF: 13.6

2009-01-01

Journal of Hazardous Materials

Abstract:To reveal the mechanisms of flame propagation through the hardly volatile metal dust clouds clearly, the flame propagating through zirconium particle clouds has been examined experimentally. A high-speed video camera was used to record the propagation process of the flame. Combustion zone temperature was detected by a fine thermocouple. Based on the experimental results, structure of flame and combustion courses of zirconium particles were analyzed, the combustion propagation in zirconium dust was investigated, and the velocity and temperature characteristics of the combustion zone were also elucidated. The combustion zone propagating through zirconium particle clouds consists of luminous particles. Particle concentration plays an important role in the combustion zone propagation process. With the increase of zirconium particle concentration, the maximum temperature of the combustion zone increases at the lower concentration, takes a maximum value, and then decreases at the higher concentration. It is also found that the propagation velocity of the combustion zone has a linear relationship with its maximum temperature.
Flame Propagation Characteristic of Zirconium Particle Cloud

DING Yi-bin,SUN Jin-hua,HE Xue-chao,YIN Yi,XU Yao,HUANG Xin-jie

2010-01-01

Abstract:The flame propagation characteristic of zirconium particle cloud in square-open tube was investigated.The zirconium dust was dispersed into the chamber by pressuring air flow to form a zirconium particle cloud,which was then ignited by an electrode spark.A high-speed video camera was used to record the images of flame propagation.Micro-thermocouples were used to obtain temperature profiles and schlieren optical system was used to detect flame structure.The results demonstrate that flame propagation velocity and temperature increase with the increase of dust cloud concentration at lower concentration,which reach the maximum values of 30.41 m/s and 1 716 K respectively at 0.627 kg/m3,and then decrease slightly at higher concentration.Zirconium particles and air form surface combustion system and micro-explosion occurs to some particles before the end of combustion.Preheat zone thickness is between 0.39—2.52 cm,which decreases first and then increases with the increase of dust concentration.
Flame Propagation Characteristics and Flame Structures of Zirconium Particle Cloud in a Small-Scale Chamber

YiBin Ding,JinHua Sun,XueChao He,QiuHong Wang,Yi Yin,Yao Xu,XianFeng Chen

DOI: https://doi.org/10.1007/s11434-010-4140-1

2010-01-01

Chinese Science Bulletin

Abstract:Flame propagating through zirconium particle cloud in a small-scale vertical rectangle chamber was investigated experimentally. In the experiments, the zirconium quoted 99% purity was used and the diameter of particles was distributed 1–22 μm. The zirconium dust was dispersed into the chamber by air flow and ignited by an electrode spark. A high-speed video camera was used to record the images of the propagating flame. Micro-thermocouples, schlieren optical system and microscopic lens were used to obtain temperature profiles and flame structure, respectively. Based on the experimental results, flame propagation characteristics and flame structure of zirconium particle cloud were analyzed. The propagation velocity of the flame is quite slow in the initial 14 ms and then accelerates to maximum value. Subsequently, the propagation velocity of the flame almost keeps constant. The combustion zone width of zirconium particle cloud is 5–6 mm. Smaller particles burn mainly at the leading edge of combustion zone in the width of 1.4 mm followed by larger particles burning 1.4–6 mm behind the leading edge of the combustion zone. Gas phase flame is not seen in zirconium particle cloud and the combustion time of single zirconium particle is 1–5 ms, which depends on its original size. The preheated zone is 7–8 mm thickness ahead of the combustion zone and intensive chemical reaction takes place at 490 K. The maximum flame temperature increases at lower concentrations, reaches the maximum value, and then decreases slightly at higher concentrations.
Flame Temperature Characteristics of Multi-Tube Injection Combustion of Zirconium-Air Cloud Mixtures

WANG Qiu-hong,SUN Jin-hua,ZHOU Qi,XU Yao,ZHU Hong-ya,ZHANG Ying

2012-01-01

Abstract:The flame temperature characteristics of multi-tube injection combustion of zirconium-air cloud mixtures were investigated by means of self-designed experimental system of continuance spray combustion of premixing dust cloud.The flame emissivity and the temperature distribution of spray flame of zirconium-air cloud mixtures were analyzed by comparing point temperature with area temperature.The analytical results indicate that the flame emissivity of zirconium-air cloud mixtures with the dust concentration of 328.48,g/m3,410.35,g/m3,483.59,g/m3,is 0.20,0.19 and 0.18,respectively,and the maximum flame temperature is 2,147.5,℃,2,248.1,℃ and 2,377.8,℃,respectively.Experiments also show that the tendency of flame temperature towards the central axis of flame is increase-decrease-slight increase,the slight increase of flame temperature occurrs in the flame intermission area,and the maximum flame temperature occurs at the place about 5 cm centimeters from the outlet of combustion device.
Flame temperature and propagation speed characteristics of zirconium dust cloud flame propagation in pipelines

WANG Qiu-hong,SUN Jin-hua,DENG Jun

DOI: https://doi.org/10.13374/j.issn1001-053x.2014.10.015

2014-01-01

Abstract:Zirconium powder is widely applied as high-energy fuel for it has not only a faster burning speed but also a stronger burning heat. Flame comes into being from the combustion of zirconium dust cloud with a lot of zirconium particles suspending in the air. A transient flame propagation experimental system was established to study the flame temperature and flame propagation speed characteristics of zirconium dust cloud in a vertical pipeline. The results indicate that the maximum flame temperature and the maximum flame propagation speed of zirconium dust cloud have the same changing trend at thermocouple positions, i. e. , both their values increase firstly and then decrease with the increasing concentration of zirconium dust cloud. The maximum flame temperature reaches 1777. 81 ℃and the maximum flame propagation speed is up to 39. 7 m·s-1 when the concentration of zirconium dust cloud at 0. 625 kg·m-3 . But when the concentration exceeds 0. 625kg·m-3 , both the maximum flame temperature and the maximum flame propagation speed decrease. The main reason is that zirconium particles occur incompletely burning owing to rich fuel combustion in the pipeline.
Characteristics of Flame Propagation Speed of Zirconium Dust Cloud in Vertical Pipeline and Model of Zirconium Particles Combustion

Qiu-hong WANG,Jin-hua SUN,Hu WEN,Qing-feng WANG

DOI: https://doi.org/10.15918/j.tbit1001-0645.2015.04.005

2015-01-01

Abstract:A lot of fine suspended zirconium particles can develop to become a range of flame when zirconium dust cloud burns.Zirconium powder material was widely applied as a kind of high energy fuel.Dust cloud transient flame propagation experimental system was used to study the characteristics of flame propagation speed of zirconium metal dust cloud in a vertical pipeline,and a combustion model of zirconium particles moving upward in the pipeline was established.The results show that zirconium dioxide particles have two kinds of crystal phase-monoclinic crystal phase and tetragonal crystal phase.The zirconium dust cloud concentration is high or low which can be judged preliminarily according to the initial shape of the flame fronts.The maximum flame propagation speed of zirconium powder cloud first increase then decrease with the increasing zirconium dust cloud concentration,because the oxygen in the pipeline is not enough as result ofrich fuel combustion and the heat energy are absorbed by the unburned particles.When the zirconium dust cloud concentration is 0.625kg/m3,the fastest flame propagation speed in the pipeline is up to 39.7m/s.In addition,a combustion model of zirconium particles moving upward in the pipeline was established,the whole combustion process was divided into four stages.The flame propagation process of zirconium dust cloud in vertical pipeline are characterized from macro phenomenon and the micro mechanism.
Evolution of particle temperature and internal composition for zirconium burning in air

I.E. Molodetsky,E.L. Dreizin,C.K. Law

DOI: https://doi.org/10.1016/S0082-0784(96)80014-2

1996-01-01

Symposium (International) on Combustion

Abstract:An experimental study of single zirconium particle combustion in air is presented, with emphasis on understanding the mechanism cansing particle temperature jumps and the subsequent explosions. The experiment involved generating uniform, ∼200 μm-size particles of controlled initial temperature by a pulsed micro-arc, letting them burn in air in free fall, measuring their instantaneous temperatures with a three-wavelength optical pyrometer, quenching the burning particles during varions stages of burning, and subsequently analyzing the particles' internal compositions using a high-resolution X-ray electron microprobe. Special techniques were developed to separate ont the radiation from the gas-phase luminous zone in the temperature determination, and to rapidly quench the particles in order to freeze their internal composition. Results show that during combustion, the particle temperature first increases and then decreases: oxygen and nitrogen are dissolved in the particle interior whereas no oxide (or nitride) shells or inclusions have been detected. The maximum particle temperature is considerably less than the boiling temperatures of zr and zrO 2 : It is demonstrated that the occurrence of the particle temperature jumps and explosions is due to the attainment of the eutectic state within the particle interior, which to the and explosions is due to the attainment of the eutectic state within the particle interior, which leads to the precipitous formation of solid or and rO 2 from supersaturated r−O solution, with simulataneous heat release and nitrogen gas release.
Preparation and Flame Ablation Resistance of Al/Zn/Cu-Incorporated Yttria Partially Stabilized Zirconia Coating

Yuxing Fan,Haoliang Tian,Shuaishuai Zhu,Cong Fang,Baosen Zhang

DOI: https://doi.org/10.1007/s11665-024-09296-8

IF: 2.3

2024-03-14

Journal of Materials Engineering and Performance

Abstract:Al/Zn/Cu-incorporated yttria partially stabilized zirconia (YSZ) coating was prepared on carbon fiber-reinforced polyimide sheets by the detonation spraying process to enhance the heat resistance of resin composites. The microstructure and phase composition of the coatings were analyzed by using XRD, SEM and XPS. The flame ablation platform was used to analyze the coating's thermal protection capabilities. The coating failure process and the protection mechanisms of Al, Zn, and Cu metals were examined and described. The results show that it is possible to prepare dense coatings with good bonding between layers using detonation spraying. In the working layer, both Al and Zn additive phases were oxidized to some extent and the oxidation products were Al 2 O 3 and ZnO. Al and Zn play the role of melting and heat absorption to lower the temperature, and the newly generated Al 2 O 3 , ZnO and CuO under the high temperature play the role of repairing the cracks in the coatings, slowing down the growth of the thermally grown oxide (TGO) as well as the role of heat insulation.

materials science, multidisciplinary
The effects of zirconium diboride particles on the ablation performance of carbon-phenolic composites under an oxyacetylene flame

Yaxi Chen,Changqing Hong,Ping Chen

DOI: https://doi.org/10.1039/c3ra41265b

IF: 4.036

2013-01-01

RSC Advances

Abstract:ZrB2 modified carbon-phenolic (C-Ph) composites are fabricated by the impregnation method, and the ablation performance of the composites is tested using an oxyacetylene flame. In addition, the microstructure of the ablation zone is observed with a scanning electron microscope (SEM). The results indicate that the linear ablation rate decreases with increasing ZrB2 content, and the ZrB2-C-Ph composites have their lowest linear ablation rate when the ZrB2 to phenolic resin weight ratio is 0.09 : 1. The main ablation mechanisms of the composites with low loading of ZrB2 are oxidation and char spallation. When more ZrB2 particles are introduced, a continuous protective ZrO2 layer is properly formed on the ablated surface of the specimen, and the stripping of the protective ZrO2 layer and the oxidation of carbon are the main ablation mechanisms. Furthermore, the forming-stripping process of a protective ZrO2 layer occurred continuously and was repeated during the ablation process.
Suppression on heat and smoke diffusion by zirconium nitride (ZrN) in intumescent flame retardant epoxy coatings

Feng Weihua,Wang Yufei,Tang Bo,Zhang Sheng,Gu Xiaoyu,Li Hongfei,Sun Jun

DOI: https://doi.org/10.1016/j.porgcoat.2020.105714

IF: 6.6

2020-09-01

Progress in Organic Coatings

Abstract:In order to control heat and smoke release of the intumescent flame retardant (IFR) epoxy coating on steel during fire hazard, a little amount of zirconium nitride (ZrN) of 1~3 wt% was introduced into the coating. The back temperature test showed it used about 46.1 min for the steel plate coated with IFR coating without ZrN to reach 580 °C, however by using of 3 wt% ZrN, the time was prolonged to 61 min, indicating the steel structure can be kept for more than 15 min. The result is very important to the safety of steel structure, meaning more escape time during a fire hazard. Furthermore in cone test, the coating containing ZrN exhibited more control on heat and smoke release. For example, compared with the IFR coating containing no ZrN, coating containing 3 wt% ZrN cut more than 20.3% total heat release (THR) and 40.0% smoke production (SPR).The graphitization degree increase of char was documented by Raman spectrum; and in XRD patterns some special peaks of ZrP2O7 and Ti0.8Zr0.2P2O7 was found in char, all the results indicated ZrN participated into the charring with IFR and TiO2 together and then promote formation of more compact char structure.

materials science, coatings & films,chemistry, applied
Time Scale Analysis on Precursor-Particle Transformation in Flame Aerosol Synthesis

Yi-Chen ZONG,Pei-Dong SONG,Chen-Yang LIU,Shui-Qing LI,Qiang YAO

2016-01-01

Journal of Engineering Thermophysics

Abstract:Zirconium oxide nanoparticles were synthesized through Hencken burner flame,with the average size as (23.1±1.9) nm.Based on time scale analysis,the precursor-particle transformation in flame was carefully investigated.The reaction characteristic time for precursor,as well as the collision/sintering characteristic time for particles,was calculated under flame temperatures.The decomposition reaction of precursor is found to occur as the first step within 10-5～10-4 s.The collision/sintering processes take 10-4～10-1 s to finish for particles in growth,which is the ratedetermining step in flame synthesis.The competition between collision and sintering also determines the final particle morphology as single spherical particles or agglomerates,which is confirmed by the TEM images.
One zirconia-based ceramic coating strategy of combustion stabilization for fuel-rich flames in a small-scale burner

Fan Li,Haolin Yang,Yue Ye,Liqiao Jiang,Xiaojun Zeng,Daiqing Zhao,Xiaohan Wang

DOI: https://doi.org/10.1016/j.fuel.2021.122306

IF: 7.4

2022-02-01

Fuel

Abstract:From the perspective of the thermal/chemical performance management of a slot burner, three kinds of blended coatings with the low thermal conductivity and certain chemical activities, including 30wt.%Y2O3/ZrO2, 30wt.%MgO/ZrO2 and 30wt.%Al2O3/ZrO2, were prepared on stainless steel walls plated by atmospheric plasma spraying. The effects of coating material, wall temperature, and equivalence ratio on fuel-rich methane flame characteristics were investigated experimentally. The OH planar laser-induced fluorescence (OH-PLIF) technique was used to obtain OH intensity and flame anchoring location. The physical and chemical properties of different coatings before and after spraying were analyzed by a series of material and surface characterization techniques. Results show that compared with pure ZrO2 coating, the quenching distances of three ZrO2-based blended coatings with Y2O3, MgO, and Al2O3 decrease to some extent, resulting in the minimum quenching distance of Al2O3/ZrO2 coating, and the maximum one for Y2O3/ZrO2 coating. Meanwhile, the blended coating walls result in the higher flame anchoring location than that of pure ZrO2 in most cases, in which the coating of Y2O3/ZrO2 displays the highest location. The blended coatings have higher thermal conductivity, which is beneficial to balance part of the heat loss through the axial heat recirculation of wall structures, and thus expanding stability limits at low temperatures. In addition, partial lattice solid solutions are formed in mixture systems after the ultra-high-temperature thermal spraying, leading to more surface lattice oxygen and stronger chemical promotion. In , reasonable allocation of ZrO2-based ceramic components as coating wall is an effective alternative strategy to control flame stabilization in small-scale combustion devices.

energy & fuels,engineering, chemical
Size Resolved High Temperature Oxidation Kinetics of Nano-Sized Titanium and Zirconium Particles.

Yichen Zong,Rohit J. Jacob,Shuiqing Li,Michael R. Zachariah

DOI: https://doi.org/10.1021/acs.jpca.5b02590

2015-01-01

The Journal of Physical Chemistry A

Abstract:While ultrafine metal particles offer the possibility of very high energy density fuels, there is considerable uncertainty in the mechanism by which metal nanoparticles burn, and few studies that have examined the size dependence to their kinetics at the nanoscale. In this work we quantify the size dependence to the burning rate of titanium and zirconium nanoparticles. Nanoparticles in the range of 20-150 nm were produced via pulsed laser ablation, and then in-flight size-selected using differential electrical mobility. The size-selected oxide free metal particles were directly injected into the post flame region of a laminar flame to create a high temperature (1700-2500 K) oxidizing environment. The reaction was monitored using high-speed videography by tracking the emission from individual nanoparticles. We find that sintering occurs prior to significant reaction, and that once sintering is accounted for, the rate of combustion follows a near nearly (diameter)(1) power-law dependence. Additionally, Arrhenius parameters for the combustion of these nanoparticles were evaluated by measuring the burn times at different ambient temperatures. The optical emission from combustion was also used to model the oxidation process, which we find can be reasonably described with a kinetically controlled shrinking core model.
Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

Yang Hu,Jun Lu,Dewei Ni,Bowen Chen,Feiyan Cai,Zou Xuegang,Xiangyu Zhang,Yusheng Ding,Shaoming Dong

DOI: https://doi.org/10.1016/j.jeurceramsoc.2024.01.038

IF: 5.7

2024-06-01

Journal of the European Ceramic Society

Abstract:In this study, short carbon fibre (Csf) reinforced ZrB2-SiC composites were fabricated via direct ink writing followed by precursor infiltration and pyrolysis. The ablation behaviour of the composites was investigated at heat fluxes of 4–6 MW/m2 under an air plasma flame, which revealed excellent ablation resistance with negative linear ablation rates of − 0.1 to − 0.5 µm/s. The results showed that ZrO2-SiO2 oxide layer was formed on the ablation surface after ablation, which provided effective protection to the internal materials. With an increase in heat flux, ZrO2 precipitated from the SiO2 melt first in the form of nano-tetragonal ZrO2 (t-ZrO2), owing to the vaporisation of SiO2. During cooling, the nano t-ZrO2 particles were retained, and some of them reacted with SiO2 to form ZrSiO4, thus improving the thermal stability of the SiO2-ZrO2 oxide layer. In contrast, t-ZrO2 agglomerated and grew owing to capillary force and finally transformed into monoclinic ZrO2 (m-ZrO2). Moreover, a higher heat flux led to the size of precipitation ZrO2 increases, meanwhile increasing the content of t-ZrO2 and ZrSiO4 in the oxide layer.

materials science, ceramics
Ablation Behavior of ZrB2–SiC–ZrO2 Ceramic Composites by Means of the Oxyacetylene Torch

Shanbao Zhou,Weijie Li,Ping Hu,Changqing Hong,Ling Weng

DOI: https://doi.org/10.1016/j.corsci.2009.05.035

IF: 7.72

2009-01-01

Corrosion Science

Abstract:Ablation behavior of ZrB2–SiC–ZrO2 ceramics with two ZrO2 contents was investigated using oxyacetylene torch. Thermogravimetric analysis demonstrated that ceramic with 10vol% ZrO2 showed initial weight change at higher temperature than the one with 20vol% ZrO2. After same ablation condition, lighter oxidized microstructure and lower weight loss and line gain were obtained from ceramic with 10vol% ZrO2. Ablation mechanism revealed that excessive ZrO2 would supply much path to the inward transport of oxygen, which led to the dissatisfactory resistance to oxidation and ablation for the ceramic with 20vol% ZrO2.
Effect of micron-sized zirconium powder on combustion decomposition behavior of molecular perovskite energetic material DAP-4

Kaili Liang,Yang Liu,Lishuang Hu,Jiashun Liang,Tiancheng Lv,Yanping Wang,Shuangqi Hu

DOI: https://doi.org/10.1016/j.cplett.2023.140740

IF: 2.719

2023-07-29

Chemical Physics Letters

Abstract:Micron-sized zirconium (μZr) is a viable alternative fuel source for high-energy propellants. To explore the combustion performance of Zr-containing DAP-4-based composites, DAP-4/Zr and F/DAP-4/Zr composites were designed. The results showed that the optimized composite had high combustion performance. When DAP-4/Zr was 54:46, the sample had the highest combustion heat and the fastest flame spreading velocity. The combustion time of F/DAP-4/Zr became longer after adding F 2602 , and the flame spread was the fastest when F/DAP-4/Zr was 10:48.6:41.4. The results indicate that the introduction of μZr as a fuel in DAP-4 can improve the material's energy density and combustion characteristics.

chemistry, physical,physics, atomic, molecular & chemical

Flame propagation through zirconium particles coated with different ratios of Fe 3 O 4

Flame Propagation Characteristic of Zirconium Particle and Zirconium Particle Coated with Fe3O4

Flame Propagation Characteristics and Combustion Mechanism of FeOOH-coated Zirconium Particles

Combustion Characteristics of Zirconium Particles Coated with Ferrite Nanoparticles

Combustion Behaviour of Fe 2 O 3 -coated Zirconium Particles in Air

Experimental study on flames propagating through zirconium particle clouds.

Flame Propagation Characteristic of Zirconium Particle Cloud

Flame Propagation Characteristics and Flame Structures of Zirconium Particle Cloud in a Small-Scale Chamber

Flame Temperature Characteristics of Multi-Tube Injection Combustion of Zirconium-Air Cloud Mixtures

Flame temperature and propagation speed characteristics of zirconium dust cloud flame propagation in pipelines

Characteristics of Flame Propagation Speed of Zirconium Dust Cloud in Vertical Pipeline and Model of Zirconium Particles Combustion

Evolution of particle temperature and internal composition for zirconium burning in air

Preparation and Flame Ablation Resistance of Al/Zn/Cu-Incorporated Yttria Partially Stabilized Zirconia Coating

The effects of zirconium diboride particles on the ablation performance of carbon-phenolic composites under an oxyacetylene flame

Suppression on heat and smoke diffusion by zirconium nitride (ZrN) in intumescent flame retardant epoxy coatings

Time Scale Analysis on Precursor-Particle Transformation in Flame Aerosol Synthesis

One zirconia-based ceramic coating strategy of combustion stabilization for fuel-rich flames in a small-scale burner

Size Resolved High Temperature Oxidation Kinetics of Nano-Sized Titanium and Zirconium Particles.

Microstructure evolution and ablation mechanisms of Csf/ZrB2-SiC composites at different heat fluxes under air plasma flame

Ablation Behavior of ZrB2–SiC–ZrO2 Ceramic Composites by Means of the Oxyacetylene Torch

Effect of micron-sized zirconium powder on combustion decomposition behavior of molecular perovskite energetic material DAP-4