Abstract:The C=C double bonds in the main chain of hydroxyl-terminated polybutadiene (DHTPB), obtained by the degradation of polybutadiene rubber, were partially epoxided using m-chloroperoxybenzoic acid (mCPBA) as epoxidation reagent. A series of epoxided HTPBs (EHTPB) with different epoxy contents (5%, 10% and 15%) were prepared by tuning the molar ratio of mCPBA to C=C double bonds. The structures of EHTPBs were characterized by Fourier transform-infrared (FTIR), nuclear magnetic resonance (H-1-NMR) spectroscopy and gel permeation chromatography (GPC). The epoxy percent in EHTPBs from H-1-NMR spectra was in accordance with the design. In addition, a series of EHTPB-based polyurethane elastomers (EPU) were prepared by the reaction between EHTPB and 4,4'-diphenylmethane diisocyanate with 1,4-butanediol as a chain extender. Mechanical and thermal properties of the EPU samples were characterized by tensile test, differential scanning calorimetry (DSC) and thermal gravity analysis (TGA). With increased epoxy percent in EHTPB, the Young's modulus and the tensile strength of the EPU samples increased, whereas the elongation at break decreased. The sample EPU10 prepared with 10% of epoxy had the best mechanical properties with 8.82 MPa as Young's modulus, 7.83 MPa as tensile strength, and (485 +/- 23)% as elongation at break. The elasticity recovery of the EPU sample was slightly better than HTPB-based PU (EPU0). The results with TGA test showed that the thermal degradation of EPU, similar to EPU0, was divided into three stages. However, the EPU samples had better thermal stability with the initial degradation temperature at 210 degrees C, about 30 degrees C higher than that of EPU0. The DSC results showed that the glass transition temperature (T-g) of EPU gradually increased as epoxy percent was increased, though still lower than that of HTPB (FHTPB) based PUs prepared by free-radical polymerization.

Synthesis and Characterization of Crystallizable Aliphatic Thermoplastic Poly(ester Urethane) Elastomers Through a Non-Isocyanate Route

Crystallizable and Tough Aliphatic Thermoplastic Polyureas Synthesized Through a Nonisocyanate Route

Viscoelastic Property Evolution of Thermoplastic Polyurethane During Annealing Treatment and Its Correlation with Segmental Crystallization

Preparation and Properties of Epoxided Hydroxyl-terminated Polybutadiene Based Polyurethane Elastomers

Facile Synthesis of Novel HTPBs and EHTPBs with High Cis-1,4 Content and Extremely Low Glass Transition Temperature

Aliphatic Thermoplastic Poly(Ether Urethane)S Having Long Peg Sequences Synthesized Through A Non-Isocyanate Route

The Structure and Dynamic Properties of Thermoplastic Polyurethane Elastomer/Hindered Phenol Hybrids

Synthesis and properties of high performance thermoplastic polycarbonate polyurethane elastomers through a non-isocyanate route

Oriented distribution structure, interaction, and performance of thermoplastic polyurethane/selective hindered amine hybrids

Studies on the Synthesis and Properties of Aliphatic Thermoplastic Polyurethanes via Non-isocyanate Route

Synthesis and Properties of Non-Isocyanate Thermoplastic Polyurethanes Containing Dibutylene Terephthalate Units

Aliphatic Thermoplastic Polyurethane-Ureas and Polyureas Synthesized Through a Non-Isocyanate Route

One-Shot Synthesis of Thermoplastic Polyurethane Based on Bio-Polyol (Polytrimethylene Ether Glycol) and Characterization of Micro-Phase Separation

Synthesis of Thermoplastic Polyurethanes Containing Bio-Based Polyester Polyol and Their Fiber Property

Synthesis, Characterization and Non-Isothermal Crystallization Kinetics of a New Family of Poly (Ether-Block-Amide)s Based on Nylon 10T/10I

Solvent-Free One-Shot Synthesis of Thermoplastic Polyurethane Based on Bio-Poly(1,3-propylene succinate) Glycol with Temperature-Sensitive Shape Memory Behavior

Synthesis and Characterization of Aliphatic Poly(Amide Urethane)S Having Different Nylon 6 Segments Through Non-Isocyanate Route

Mechanical properties of thermoplastic polyurethanes containing aliphatic polycarbonate soft segments with different chemical structures

Study on Properties and Preparation of Thermoplastic Polyurethane Hot-Melt Adhesive

Polyether–polyimide Thermoplastic Elastomers. I. Synthesis and Properties

Strong aliphatic crosslinked polyureas synthesized through a non-isocyanate route and a Michael addition with an aliphatic bismaleimide