Abstract:To comprehensively reveal the influence regularity of different glass melting temperatures on the ultraviolet (UV) laser-induced damage resistance of fluoride-containing phosphate glasses, the initial bulk damage, damaged growth, and dynamic behaviors of both fundamental-frequency (1ω) absorptive and third-harmonic-frequency (3ω) transparent fluoride-containing phosphate glasses are explored utilizing the time-resolved pump–probe shadowgraph technique. A low-temperature (1000 °C) glass melting process resulted in an increase in the absorption coefficient at 355 nm and decrease in the optical bandgap for the 1ω absorptive glass. The produced 1ω absorptive glass was subjected to higher shock pressure and shock temperature on the rear surface after a single-pulse laser irradiation, and had a more serious filamentation damage accompanied by a funnel-shape morphology. With the subsequent multiples irradiation, the initial bulk damage area increased exponentially with a growth coefficient of 0.72. The corresponding exponential growth coefficient for the counterpart 1ω absorptive glass melted at a high temperature (1200 °C) was only 0.32 due to its slight initial bulk damage. In contrast, for the 3ω transparent glass, the high-temperature (1200 °C) melting process led to a larger initial bulk damage area and largest exponential growth coefficient of 0.91, 1.1 times that of the 3ω transparent glass melted at a low temperature (1000 °C). They exhibited wave-packed damaged morphologies extending from the rear surface into the glass body. The melting temperatures exhibited the opposite influence regularity for these two investigated fluoride-containing phosphate glasses. The high-temperature (1200 °C) melting process favored the improvement in UV laser-induced damage resistance of the 1ω absorptive glass, as evidenced by the higher UV laser-induced damage threshold and lower damage growth coefficient, while the low-temperature (1000 °C) melting process exerted similar effects on the 3ω transparent glass.

Effect of Both Acid and Base Etching on Phosphate Laser Glass Surfaces

Phosphate/Silicate Ratio Allows for Fine-Tuning of Bioactive Glass Crystallisation and Glass-Ceramic Microstructure

Experimental Investigation of Enhancing the Subsurface Damage Threshold of Nd-Doped Phosphate Glass

Influence of Mixed Na2O/K2O on Chemical Durability and Spectral Properties of P2O5-Al2O3-BaO-K2O-Na2O-Nd2O3 Phosphate Glasses

Experimental Investigation on Laser-Induced Surface Damage Threshold of Nd-Doped Phosphate Glass

Effect of Al_2O_3 on structure and properties of Al_2O_3-K_2O-P_2O_5 glasses

Mechanical–Structural Investigation of Chemical Strengthening Aluminosilicate Glass Through Introducing Phosphorus Pentoxide

The Role of Phosphate in the Glass Forming Region, Structure and Mechanical Properties for the SiO2-Al2O3-P2O5 System Contains High-Aluminum

Water Corrosion of Commercial Neodymium-Doped Phosphate High-Peak-power Laser Glass

Study on surface modification and optical properties of Nd-doped phosphate glass

Effects of Phosphorus Pentoxide Content on Ion Exchange Performance of Aluminosilicate Glasses

Effect of alkali and alkaline earth metal ion as glass modifiers on the spectroscopic characteristics of Er3+‐ion doped lead silicate glasses

Network of Bi 2 O 3 –Al 2 O 3 –NaPO 3 glasses studied by solid‐state nuclear magnetic resonance spectroscopy

Effects of Doping SiO2 on the Defect's Change in B2O3-containing Phosphate Based Laser Glasses Used for High Energy UV Lasers

(INVITED) Impurities in Large Scale Produced Nd-doped Phosphate Laser Glasses. I. Cu Ions

(INVITED) Impurities in Large Scale Produced Nd-doped Phosphate Laser Glasses. II. Pt Ion and Pt Inclusion

Study on the effect of crystal changes on acid resistance of erbium laser etched enamel surface

Effect of Silica-Alumina Co-Introduction on Structure As Well As Physical and Spectroscopic Properties of Nd3+-doped Potassium Phosphate Glass

Bulk damage growth characteristics and ultrafast diagnosis of fluoride-containing phosphate glasses induced by 355-nm laser

Study of Through Glass Via (TGV) Using Bessel Beam, Ultrashort Two-Pulses of Laser and Selective Chemical Etching

The influence of chemical etching on the surface quality of phase components