Abstract:The microstructural characteristics and morphological attributes of the target material, along with its intrinsic properties, can significantly influence the performance of the resultant film. Currently, commercially available nickel-vanadium targets employed in the industry have not been subjected to investigations aimed at controlling grain size and grain orientation. This study examines the effects of unidirectional rolling at room temperature, combined with substantial deformation, on the alterations in microstructure, texture evolution, and mechanical properties of the NiV7 alloy. The process of severe plastic cold rolling leads to a continuous elongation and refinement of the grains. The changes in microstructure and texture of the cold-rolled sheets were analyzed using electron backscatter diffraction (EBSD) technology. At an 80% reduction, a significant number of sub-grains are observed, which transform into deformed grains as the reduction reaches 95%. With a thickness reduction of 96.6%, the average grain size is approximately 1.10μm. Further increases in reduction do not lead to significant alterations in the grain structure; instead, the grain orientation progressively becomes more uniform with higher levels of deformation. The combination of substantial deformation and lower rolling rates results in an increased number of high-angle grain boundaries. The alloy displays various textures throughout the rolling process, including S-type, copper-type, brass-type, fiber, and cubic textures. Notably, the prevalence of S-type and fiber textures diminishes as the degree of deformation increases, while the cubic texture becomes increasingly prominent. Upon achieving a reduction of 95%, the cubic texture emerges as the dominant texture. A transmission electron microscope (TEM) was utilized to examine the extensive array of dislocations, dislocation cells, dislocation walls, and shear bands generated during the cold rolling process. At a deformation level of 96.6%, the ultimate tensile strength of the alloy demonstrates a significant enhancement, attributed to mechanisms of dislocation strengthening and grain strengthening, reaching a value of 1231±20 MPa, accompanied by a post-fracture elongation of approximately 2%. The ultimate tensile strength exhibited an increase of 781±20 MPa compared to the sample prior to the rolling process; however, there was a notable reduction in plasticity.

Effects of initial texture on rolling texture and property of electrodeposited nickel plate

Effect of cross cold rolling and annealing on microstructure and texture in pure nickel

Microstructure Evolution and Texture Characteristics of Pure Nickel N6 During Cold Rolling Process

Texture and Deformation Structure Evolution During Rolling of Individual Grains of Columnar Grain Nickel

Severe plastic cold rolling effects in Nickel-Vanadium alloy: Microstructure, texture evolution and mechanical properties

Grain Orientation Induced Softening in Electrodeposited Gradient Nanostructured Nickel during Cold Rolling Deformation

Preparation of cube texturing Ni plate by rolling and recrystallization

Microstructure and Texture Evolution of Cu-Ni-P Alloy after Cold Rolling and Annealing

Analysis of Through-Thickness Heterogeneities of Microstructure and Texture in Nickel after Accumulative Roll Bonding

Research on Effects of Rolling-Drawing Deformation on Performance of Cu-10Ni-1Fe-1Mn Alloy

Recrystallization Texture Evolution of Cold-Rolled Cu Foils Governed by Microstructural and Sample Geometrical Factors During Heating

Effect of different deformation and annealing procedures on non-magnetic textured Cu60Ni40 alloy substrates

EFFECT OF ANNEALING TEMPERATURE ON TEXTURE OF COLD-ROLLED NI47TI44NB9 SHEET

Study of Effects of Initial Texture on the Microstructure and Texture for Hot Rolled AZ31 Mg Alloy Sheet Using EBSD

Effects of Strain on Recrystallization of Nickel Metals and Nanometals Produced by Heavy Cold Rolling

Effect of Change in Strain Path During Cold Rolling on the Evolution of Microstructure, Texture And Hardness Properties of Nickel With Extremely Coarse Initial Grain Size

Effect of stress-relief annealing on rolled texture of nickel-based alloys

Textures of Non-Oriented Electrical Steel Sheets Produced by Skew Cold Rolling and Annealing

Effect of Heterophase Interfaces on Microstructure and Crystallographic Texture Evolution During Rolling of Directionally Solidified Ag-Cu Eutectic Alloy

Effects of Cold Rolling Path on Recrystallization Behavior and Mechanical Properties of Pure Copper During Annealing

Texture gradient in rough-rolled plate of aluminum alloy 3104 and its effect on annealing textures evolution after hot compression