Abstract:{1011}-{1012} double twin is the most common twin type being observed in the rolled AZ31 magnesium alloy, especially at low or moderate rolling temperature. Four types of rolled AZ31 magnesium alloy sheets were produced by rolling strong basal textured AZ31 plates at 150°C and 300°C respectively through different rolling paths by two passes till total reduction 17%. The rolling paths are normal and cross rolling respectively: the rolling directions of the two passes for normal rolling are mentally paralleled while perpendicular to each other for the cross rolling. Sheets are characterized in terms of microstructure and texture using optical microscope and scanning-electron microscope equipped with EBSD detector, and their mechanical performances are measured by uniaxial tensile tests at room temperature and a strain rate of 0.001 s -1. Tensile samples are cut parallel or perpendicular to the final rolling direction to obtain the mechanical anisotropies. The effects of the {1011}-{1012} double twins occurred during rolling on the microstructure, texture and mechanical properties of the rolled sheets are discussed and related to each other. The results show that the fraction of {1011}-{1012} double twins varies widely in different rolled sheets, which are determined by the rolling temperature. The twins in different rolled sheets are arranged in different ways. In the normal rolled sheets, the traces of twins are approximately perpendicular to the final rolling direction, while in the cross rolled sheets there are both traces of twins parallel and to the final directions. This phenomenon is related to the variant selection of twinning during rolling deformation. And the variant selection law is related to the rolling direction. For the same reason, the textures of twins in the rolled sheets produced through different paths are different. The textures of twins will add onto the bulks, and increases the textural difference between the bulks. The differences between mechanical properties of the rolled sheets are also related to the different textures and microstructures of the sheets caused by twins. © Right.

Study of Effects of Initial Texture on the Microstructure and Texture for Hot Rolled AZ31 Mg Alloy Sheet Using EBSD

Effect of texture types on microstructure evolution and mechanical properties of AZ31 magnesium alloy undergoing uniaxial tension deformation at room temperature

The effect of grain size on texture evolution and mechanical properties of an AZ31 magnesium alloy during cold-rolling process

Effect of Final Rolling Temperature on Microstructures and Mechanical Properties of AZ31 Alloy Sheets Prepared by Equal Channel Angular Rolling and Continuous Bending

The Effect of Texture on the Corrosion Behavior of AZ31 Mg Alloy

Recrystallization Behavior and Mechanical Properties of Az31b Alloy During the Hot-Rolling Process

The improvement on mechanical anisotropy of AZ31 magnesium alloy sheets by multi cross-rolling process

Effect of Temperature on Microstructure and Texture During Compression of Az31

Reduction per pass effect on texture traits and mechanical anisotropy of Mg–Al–Zn–Mn–Ca alloy subjected to unidirectional and cross rolling

Effect of Al addition and rolling reduction on microstructure and texture evolution of Mg–3Sn alloy during high-speed rolling

The effect of {1011}-{1012} double twinning on the microstructure, texture and mechanical properties of AZ31 magnesium alloy sheet during rolling deformation

Effect of Current Frequency on the Mechanical Properties, Microstructure and Texture Evolution in AZ31 Magnesium Alloy Strips During Electroplastic Rolling

The effect of {10¯11}–{10¯12} double twinning on the microstructure, texture and mechanical properties of az31 magnesium alloy sheet during rolling deformation

Effect of rolling temperature on microstructure and mechanical properties of hot-rolled Mg-Al-Ca-Zn-Mn alloys

Texture modification and mechanical properties of AZ31 magnesium alloy sheet subjected to equal channel angular bending

The Dependence of Final Microstructure, Texture Evolution and Mechanical Properties of Al–Mg–Si–Cu Alloy Sheets on the Intermediate Annealing

Microstructure, texture evolution and mechanical anisotropy of Mg-Gd-Y-Zn-Zr alloy sheets produced by unidirectional and cross rolling

Evolution of the Microstructure and Mechanical Properties of AZ31 Magnesium Alloy Sheets during Multi-Pass Lowered-Temperature Rolling

Influence of Texture on the Mechanical Properties of a Mg-6Al-1Zn-0.9Sn Alloy Processed by ECAP

Investigation on the anisotropy of mechanical properties along different orientations of an AZ31 hot-extrusion bar

Effects of cryogenic treatment on microstructure and mechanical properties of AZ31 magnesium alloy rolled at different paths