Abstract:Despite the rapid progress that has been made in increasing the power conversion efficiency (PCE) of organic solar cells (OSCs) over the past decade, it is a challenge to realize efficient and environment-friendly OSCs. In this contribution, all polymer solar cells were fabricated with a blend of poly[4,8-bis(5-(2-ethylhexyl) thiophen-2-yl) benzo[1,2-b: 4,5-b'] dithiophene-co-3-fluorothieno[3,4-b] thiophene-2-carboxylate] (PTB7Th) donor and vinylene-bridged perylenediimide-based polymer (PDI-V) acceptor, in which non-halogenated tetrahydrofuran (THF) was used as the host solvent. A conventional device structure of ITO/poly(3,4-ethylenedioxythiophene): poly(styrenesulfonate) (PEDOT:PSS)/PTB7-Th:PDI-V/zirconium acetylacetonate (ZrAcac)/Al was employed, where PEDOT:PSS functioned as the hole transporting layer (HTL) and ZrAcac functioned as the electron transporting layer (ETL). The mixed solution of PTB7-Th and PDI-V was spin cast on the top of PEDOT:PSS layer to form the active layer. After that, ZrAcac solution was spin cast on the top of PTB7-Th:PDI-V layer. Different thermal annealing temperatures were used to optimize the active layer morphology. In details, OSCs without thermal annealing showed a PCE of 7.1%, with a short-circuit current (J(SC)) of 14.9 mA/cm(2), an open-circuit voltage (V-OC) of 0.74 V, and a fill factor (FF) of 64%. The devices annealed at 120 degrees C showed a high PCE of 8.1% with a J(SC) of 15.5 mA/cm(2), a V-OC of 0.74 V, and a FF of 70%. Further increasing the annealing temperature to 150 degrees C led to decreased FF and thereby a relatively lower PCE (7.4%). To the best of our knowledge, the PCE of similar to 8.1% is one of the highest PCE values reported in the literature so far for all polymer solar cells. The high and balanced hole and electron mobility partially contributed to such a high performance. These results suggest that THF as good non-halogenated solvent can be used to fabricate high-performance all polymer solar cells. Higher efficiency can be achieved for OSCs with THF solvent when better polymer acceptors are employed.

Inverted Polymer Solar Cells Integrated with A Low-Temperature-Annealed Sol-Gel-Derived Zno Film As an Electron Transport Layer

All-inorganic, Hole-Transporting-layer-free, Carbon-Based CsPbIBr2 Planar Solar Cells with ZnO As Electron-Transporting Materials

High Electron Mobility Zno Film for High-Performance Inverted Polymer Solar Cells

Single Junction Inverted Polymer Solar Cell Reaching Power Conversion Efficiency 10.31% by Employing Dual-Doped Zinc Oxide Nano-Film As Cathode Interlayer

Interface Control of Semiconducting Metal Oxide Layers for Efficient and Stable Inverted Polymer Solar Cells with Open-Circuit Voltages over 1.0 Volt

Physically Adsorbed Fullerene Layer on Positively Charged Sites on Zinc Oxide Cathode Affords Efficiency Enhancement in Inverted Polymer Solar Cell.

Self-organization of amine-based cathode interfacial materials in inverted polymer solar cells.

High-performance inverted polymer solar cells: Device characterization, optical modeling, and hole-transporting modifications

Conductive Water/Alcohol-Soluble Neutral Fullerene Derivative As an Interfacial Layer for Inverted Polymer Solar Cells with High Efficiency

Passivating ZnO with a Naphthalimide-Schiff Base As Electron Transport Layer for Inverted Polymer Solar Cells

Highly efficient inverted polymer solar cells by using solution processed MgO/ZnO composite interfacial layers

Light-Soaking-Free Inverted Polymer Solar Cells with an Efficiency of 10.5% by Compositional and Surface Modifications to a Low-Temperature-Processed TiO 2 Electron-Transport Layer.

Polymer Solar Cells with 90% External Quantum Efficiency Featuring an Ideal Light- and Charge-Manipulation Layer.

Improved Efficiency and Stability in Polymer Solar Cells Using a Tetra-nuclear Zinc(II) Complex Interfacial Layer

Manipulation of Zinc Oxide with Zirconium Doping for Efficient Inverted Organic Solar Cells

Inverted Organic Solar Cells Based on Aqueous Processed ZnO Interlayers at Low Temperature

Synergistic optimization of interfacial energy-level alignment and defect passivation toward efficient annealing-free inverted polymer solar cells

In‐Doped ZnO Electron Transport Layer for High‐Efficiency Ultrathin Flexible Organic Solar Cells

High-performance All Polymer Solar Cells Fabricated with Non-halogenated Solvent

Highly Efficient Polymer Tandem Cells and Semitransparent Cells for Solar Energy

Overcoming the Thickness Paradox: Systematical Optimization of Inverted Polymer Solar Cells