Abstract:In present study, the nanoscale assignment behavior of strain and stress state at the interface of T-2-Al6CuLi3/alpha-Al matrix is investigated by Transmission Electron Microscope (TEM) combined with Geometric phase analysis (GPA) method. The obtained results reveal the toughening effect of the icosahedral quasicrystalline phase T-2-Al6CuLi3 on cast Al-Li alloys. It is found that the precipitation of T-2-Al6CuLi3 phase consumes Li atoms in competition with delta'-Al3Li phase during the aging process, which damages yield stress (YS) and Young's modulus of alloy. Compared with Base alloy, the yield stress and Young's modulus of the Quasicrystalline alloy decrease 2.39% and 22.26%, respectively. A flat and smooth interface morphology of T-2-Al6CuLi3/alpha-Al matrix is observed in high-resolution images. Furthermore, the distribution state of the nanoscale strain shows that the matrix with higher ductility suffered most strain when the sample is subjected to the applied load. Meanwhile, the quasicrystalline phase T-2 compresses during the precipitation process, which suppresses the crack initiation and propagation along the interface of the T-2-Al6CuLi3/alpha-Al matrix. The assignment behavior of strain contributes to the enhancement of ductility and toughness of the alloy, partially alleviating the intergranular brittle fracture tendency which is common in Al-Li alloys. It is observed that the existence of quasicrystalline phases improves the elongation (EL) and product of strength and ductility (PSD) by 62.5% and more than five times without the loss of the ultimate tensile stress (UTS). Therefore, the present study provides a promising reference for the design of the quasicrystal-reinforced cast Al-Li alloys. (C) 2021 Elsevier B.V. All rights reserved.

Study on the Microstructures of Aluminum-Lithium Alloy by High Resolution Transmission Electron Microscopy

Microscopic Phase-field Simulation for Microstructure Evolution of Ni(75)Al(x)Cr(25-x)Alloy

Quantitative contribution of T1 phase to the strength of Al-Cu-Li alloys

High solid-solution strengthening mechanism of a novel aluminum-lithium alloy fabricated by electromagnetic near-net shape technology

Research and Development of Al-Zn-Mg-Cu-Li Alloys

Study on the microstructure and age hardening capability in Al–Cu–Li alloys with different Cu/Li ratio

Investigation on Microstructure and Property of Newly Developed Al-Cu-Li Alloy during Aging

Microstructure evolution and shearing behaviour of δꞌ/θꞌ/δꞌ precipitates in an aged Al-Cu-Li-Mg aluminium alloy

Influence of Microstructure on Mechanical Properties of High Strength Cast Aluminum-copper Alloy

Atomic-scale Investigation on the Evolution of T1 Precipitates in an Aged Al-Cu-Li-Mg-Ag Alloy

Study of a new high-strength aluminium-lithium alloy

Microstructures and mechanical properties of a cast Al–Cu–Li alloy during heat treatment procedure

Precipitation of T1 Phase in 2198 Al–Li Alloy Studied by Atomic-Resolution HAADF-STEM

Mechanical properties and microstructure of 1460 Al-Li alloy

Effect of aging treatment on microstructure and mechanical properties of a new Al-Li-Cu alloy

Microstructural Evolution, Phase Transition, and Physics Properties of a High Strength Cu–Ni–Si–Al Alloy

Structural Insights into T1 Precipitation and Age Hardening by Zn Alloying for T6 Treated Al–Cu–Li Based Alloys with a High Cu/Li Ratio

Microstructure Evolution of Aluminum-Lithium Alloy 2195 Undergoing Commercial Production

Insight into the aging behavior of a novel Al-Li-Cu-Mg alloy

The Nanoscale Strain Assignment Behavior of Icosahedral Quasicrystalline Phase T2-Al6CuLi3 in Cast Al-Li Alloys

Microstructure Evolution and Mechanical Behavior of Al–Li Alloy Fabricated by Laser Melting Deposition Technique