Abstract:In order to reveal the relationship between microstructure inhomogeneity and mechanical anisotropy, the Al–Cu–Li alloy 100 mm thick plate for aerospace was evaluated. The grain structure, crystallographic texture, phase structure and fractography of different thickness positions and directions were observed by optical microscopy (OM), X-ray diffraction (XRD), scanning electron microscopy (SEM), electron backscatter diffraction (EBSD) and transmission electron microscopy (TEM). The in-plane and through-thickness anisotropy were characterized by tensile properties, fracture toughness and hardness tests. The results demonstrate a greater in-plane anisotropy in yield strength at the same thickness position of the plate. The Brass texture component increases successively at T, T/4, and T/2 positions, while the Cu texture component exhibits minimal variation. The in-plane anisotropy mainly arises from the Brass texture. Through-thickness anisotropy in the same direction is primarily influenced by the diameter, number density, and volume fraction of the T1 strengthening phase. The average diameter and number density of the primary strengthening phase T1 within grains are highest at the T/2 position and lowest at the T position. The plate contains unrecrystallized, elongated pancake-like grains along the rolling direction. Fracture toughness tests conducted in the L-T and T-L directions predominantly reveal dimple-type transgranular shear fractures, while the S-L direction exhibits intergranular fracture as the primary characteristic. The crack divider delamination toughening mechanism is the main contributor to higher fracture toughness values in the L-T and T-L directions compared to those in the S-L direction. The results reveal the corresponding relationship between the microstructure inhomogeneity and the mechanical anisotropy of Al–Li alloy ultra-thick plates, and provide ideas for the adjustment of process parameters during processing deformation and the regulation of microstructure during heat treatment of large-scale Al–Li alloy thick plates, which has engineering application reference value.

Influence of Microstructure on Mechanical Properties of High Strength Cast Aluminum-copper Alloy

Effect of Alloying Elements and Processing Parameters on Microstructure and Properties of 1XXX Aluminium Alloys

Effect of Ti on Microstructure and Mechanical Properties of Die-Cast Al-Mg-Zn-Si Alloy

Microstructures and mechanical properties of a cast Al–Cu–Li alloy during heat treatment procedure

Effect of heat treatment on microstructure and tensile properties of 319 aluminum alloy

Influence of thermal exposure on the microstructure evolution and mechanical behaviors of an Al-Cu-Li alloy

Study on Microstructure and Mechanical Properties of Al-Mg-Si-Cu Aluminium Alloy with High Ductility

Microstructures and mechanical properties of Cu–Ti alloys with ultrahigh strength and high ductility by thermo-mechanical treatment

Experiment and multiscale modeling of the coupled influence of constituents and precipitates on the ductile fracture of heat-treatable aluminum alloys

A Study on High Strength, High Plasticity, Non-Heat Treated Die-Cast Aluminum Alloy

Effect of microstructural inhomogeneity on mechanical anisotropy of Al–Cu–Li alloy plate

Effect of Mn/Ag Ratio on Microstructure and Mechanical Properties of Heat-Resistant Al-Cu Alloys

Correlation of Solidification Microstructure Refining Scale, Mg Composition and Heat Treatment Conditions with Mechanical Properties in Al-7Si-Mg Cast Aluminum Alloys

Effect of Low Cu Content and Heat Treatment on the Microstructure and Mechanical Properties of High-Vacuum Die-Cast AlSiMgMn Alloys

Influence of microstructural and crystallographic inhomogeneity on tensile anisotropy in thick-section Al-Li-Cu-Mg plates

Effect of micro-alloying element Ti on mechanical properties of Cu–Cr alloy

Influences of Pouring Temperature and Cooling Rate on Microstructure and Mechanical Properties of Casting Al-Si-Cu Aluminum Alloy

Microstructure evolution and nano-phases strengthening of Al-5%Cu alloy by adding trace AlSiTiCrNiCu high entropy alloy

Effect of Cu and Mn content on solidification microstructure, T-phase formation and mechanical property of Al Cu Mn alloys

The microstructures and mechanical properties of a highly alloyed Al-Zn-Mg-Cu alloy: The role of Cu concentration

Effect of Annealing Temperature on As-Cast Ti6Al4V–5Cu Alloy Microstructure, Tensile Properties, and Fracture Toughness