Abstract:At present, the most common type of SOFC is anode-supported SOFC (AS-SOFC), in which the cell is mechanically supported by the thick fuel electrode layer. Recently, Metal-supported SOFCs (MS-SOFCs) have attracted attention because of their potential for low cost and high mechanical robustness. However, the fabrication process of MS-SOFCs has not been established. The mechanical behavior of the cells under high temperature operation has not been clarified. In this study, we fabricated prototype MS-SOFCs using the plasma spray method. The cell was tested by electrochemical measurements, residual stress measurements, and SEM/EDX to clarify the mechanical behavior of MS-SOFCs under high temperature operation. The layers of anode (NiO-YSZ), electrolyte (LSGM9182), and cathode (LSCF6428) were formed on a metal substrate (SUS430) by atmospheric pressure plasma spraying (APS) to fabricate a single cell of MS-SOFC. Open circuit voltage, AC impedance, and I-V measurements were performed at 600°C, 650°C, and 700°C. The residual stress of LSGM9182 electrolyte was evaluated by cosα method [1] under the cell operation condition using specially designed chamber. The MS-SOFC with thicker electrode layers showed the much lower OCV than that of theoretical. In addition, the electrolyte had vertical cracks between cathode and anode after the 2nd thermal cycle. However the MS-SOFC with thinner electrode layers showed the higher OCV, which was nearly theoretical value, and much better I-V characteristics than the cell with thicker electrodes. Electrochemical impedance measurement revealed the plasma sprayed electrodes showed acceptable performance even though its microstructure was not optimized. The residual stress of LSGM electrolyte in the cell did not change so much during the cell operation. This might be caused by existence of small cracks in the electrolyte layer. This research was financially supported by NEDO. [1] K.Tanaka, Journal of the Society of Materials Science,japan,vol.66,No.7 (2017) 479-487

Microstructure and Electrochemical Behavior of La0.8Sr0.2MnO3 Deposited by Solution Precursor Plasma Spraying

Low-temperature Solid Oxide Fuel Cells with Novel La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode and Functional Graded Anode

Study of the La1−xSrxMnO3 Cathode Film Prepared by a Low Power Plasma Spray Method with Liquid Solution Precursor for a Solid Oxide Fuel Cell

Structured La0.6Sr0.4Co0.2Fe0.8O3-δ cathode with large-scale vertical cracks by atmospheric laminar plasma spraying for IT-SOFCs

Preparation of bulk-like La0.8Sr0.2Ga0.8Mg0.2O3-δ coatings for porous metal-supported solid oxide fuel cells via plasma spraying at increased particle temperatures

Characterization of the Microstructure and Electrical Conductivity of Plasma-Sprayed La0.5Sr0.5CoO3 Coating

Tuning Layer-Structured La0.6sr1.4mno4+Delta Into A Promising Electrode For Intermediate-Temperature Symmetrical Solid Oxide Fuel Cells Through Surface Modification

Study on the Cathodes Material La 1- X Sr X MnO 3 for SOFC

Preparation, Structure and Performance of La0.6Sr0.4Co0.2Fe0.8O3 Cathodes of Intermediate Temperature Solid Oxide Fuel Cells

Validation and Electrochemical Characterization of LSCF Cathode Deposition on Metal Supported SOFC

Enhanced Catalytic Activity and Stability of SOFC Electrodes through Plasma-driven Surface Modification

Single crystalline La0.5Sr0.5MnO3 microcubes as cathode of solid oxide fuel cell

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Development of ScSZ Electrolyte by Very Low Pressure Plasma Spraying for High-Performance Metal-Supported SOFCs

Fabrication and performance of atmospheric plasma sprayed solid oxide fuel cells with liquid antimony anodes

Synthesis and characterization of La0.75Sr0.25Mn0.5Cr0.5-x CuxO3-δ for SOFC anode material

Plasma-Sprayed La0.2Sr0.8MnO3-La0.3Sr0.7TiO3 Bilayer Coatings Along with the Interface Healing Processing Applied as the High Dense Interconnector for Tubular Solid Oxide Fuel Cells

Electrochemical Performance and Mechanical Stress Evaluation of Metal-Supported Solid Oxide Fuel Cells Fabricated By Plasma Spray Method

Fabrication of LSM-YSZ Cathode-Supported Electrolyte Film by Dry-Pressing Method

Oxygen reduction mechanisms in nanostructured La0.8Sr0.2MnO3 cathodes for Solid Oxide Fuel Cells

Preparation of yttria-stabilized zirconia electrolyte via atmospheric plasma spraying for metal-supported solid oxide fuel cells