Abstract:Lanthanum-doped strontium titanate (La0.3Sr0.7TiO3 - δ, LST) perovskite is regarded as a promising candidate for high-temperature solid oxide fuel cells (HT-SOFCs) interconnect material due to its good phase stability, good thermal expansion matching to other components, as well as high electrical conductivity in reducing atmosphere. Atmospheric plasma spraying (APS) is a cost-effective processing method to fabricate membranes in SOFCs. However, the LST coatings deposited following the conventional routine exhibit a typical lamellar structure with a limited interlamellar bonding, which dominates the properties of interconnect including gas tightness and electrical conductivity. Besides, the preferential evaporation of Sr during plasma spraying may degrade the performance of LST coatings as interconnect for HT-SOFCs. In this paper, dense LST membranes were deposited on YSZ substrates at preheated conditions by APS. The effect of particle size of LST powders on the chemical composition, phase composition, and electrical conductivity of LST coatings were studied. It was found that the columnar grain growth across lamellar interfaces in LST coatings at the deposition temperature of ~500 °C was highly enhanced with increased interlamellar bonding ratio. Moreover, when the LST particle size is <30 μm, the evaporation of Sr increased remarkably with the decreasing of particle size. When the the LST particle size is ＞30 μm, the evaporation loss of Sr in LST coatings was greatly reduced. A vortex convection model of LST droplets during the spraying process was built to explain the effect of particle size on Sr evaporation. The electrical conductivity and stability of the LST interconnects were tested at controlled atmospheres at an operating temperature of 850 °C. The results show that the electrical conductivity of dense LST coatings prepared with large particles was greatly improved. The LST coatings exhibited excellent phase stability in both reducing and oxidizing atmospheres. Results suggest that LST interconnect with high performance can be deposited by APS through optimizing the microstructure and controlling the chemical composition.

Structured La0.6Sr0.4Co0.2Fe0.8O3-δ cathode with large-scale vertical cracks by atmospheric laminar plasma spraying for IT-SOFCs

Low-temperature Solid Oxide Fuel Cells with Novel La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode and Functional Graded Anode

Enhancing Plasma-Sprayed LSCF Cathode Performance by Infiltration Method

La 2 NiO 4+δ Infiltration of Plasma-Sprayed LSCF Coating for Cathode Performance Improvement

Effect of Deposition Temperature on the Microstructure and Performance of Vacuum Cold Sprayed Nano-structured LSCF Cathodes for Solid Oxide Fuel Cells

Characterization of the Microstructure and Electrical Conductivity of Plasma-Sprayed La0.5Sr0.5CoO3 Coating

Microstructure and Electrochemical Behavior of La0.8Sr0.2MnO3 Deposited by Solution Precursor Plasma Spraying

Performance of La0.8Sr0.2Ga0.8Mg0.2O3-based SOFCs with Atmospheric Plasma Sprayed La-doped CeO2 Buffer Layer

Development of ScSZ Electrolyte by Very Low Pressure Plasma Spraying for High-Performance Metal-Supported SOFCs

Vacuum Cold Sprayed Nanostructured La0.6Sr0.4Co0.2Fe0.8O3−δ As a High-Performance Cathode for Porous Metal-Supported Solid Oxide Fuel Cells Operating below 600 °C

Validation and Electrochemical Characterization of LSCF Cathode Deposition on Metal Supported SOFC

Effects of protective coating prepared by atmospheric plasma spraying on planar SOFC interconnect

Thermally Sprayed High-Performance Porous Metal-Supported Solid Oxide Fuel Cells With Nanostructured La0.6sr0.4co0.2fe0.8o3-Delta Cathodes

Preparation of bulk-like La0.8Sr0.2Ga0.8Mg0.2O3-δ coatings for porous metal-supported solid oxide fuel cells via plasma spraying at increased particle temperatures

Microstructures and Electrochemical Behavior of LSM Cathode with a Structured Electrolyte Modified by Flame Spraying

Atmospheric Plasma-Sprayed La0.3Sr0.7TiO3-δInterconnect for High-Temperature Solid Oxide Fuel Cells

Microstructure and Electrochemical Behavior of a Structured Electrolyte/LSM-Cathode Interface Modified by Flame Spraying for Solid Oxide Fuel Cell Application

Effect of Spray Parameters on the Electrical Conductivity of Plasma-Sprayed La1−xSrxMnO3 Coating for the Cathode of SOFCs

Optimization of Plasma-Sprayed Lanthanum Chromite Interconnector Through Powder Design and Critical Process Parameters Control

Microstructure and Electrochemical Behavior of Sm0.5Sr0.5CoO3 Deposited by Solution Precursor Plasma Spraying

Preparation, Structure and Performance of La0.6Sr0.4Co0.2Fe0.8O3 Cathodes of Intermediate Temperature Solid Oxide Fuel Cells