Abstract:Lanthanum-doped strontium titanate (La0.3Sr0.7TiO3 - δ, LST) perovskite is regarded as a promising candidate for high-temperature solid oxide fuel cells (HT-SOFCs) interconnect material due to its good phase stability, good thermal expansion matching to other components, as well as high electrical conductivity in reducing atmosphere. Atmospheric plasma spraying (APS) is a cost-effective processing method to fabricate membranes in SOFCs. However, the LST coatings deposited following the conventional routine exhibit a typical lamellar structure with a limited interlamellar bonding, which dominates the properties of interconnect including gas tightness and electrical conductivity. Besides, the preferential evaporation of Sr during plasma spraying may degrade the performance of LST coatings as interconnect for HT-SOFCs. In this paper, dense LST membranes were deposited on YSZ substrates at preheated conditions by APS. The effect of particle size of LST powders on the chemical composition, phase composition, and electrical conductivity of LST coatings were studied. It was found that the columnar grain growth across lamellar interfaces in LST coatings at the deposition temperature of ~500 °C was highly enhanced with increased interlamellar bonding ratio. Moreover, when the LST particle size is <30 μm, the evaporation of Sr increased remarkably with the decreasing of particle size. When the the LST particle size is ＞30 μm, the evaporation loss of Sr in LST coatings was greatly reduced. A vortex convection model of LST droplets during the spraying process was built to explain the effect of particle size on Sr evaporation. The electrical conductivity and stability of the LST interconnects were tested at controlled atmospheres at an operating temperature of 850 °C. The results show that the electrical conductivity of dense LST coatings prepared with large particles was greatly improved. The LST coatings exhibited excellent phase stability in both reducing and oxidizing atmospheres. Results suggest that LST interconnect with high performance can be deposited by APS through optimizing the microstructure and controlling the chemical composition.

Plasma-Sprayed La0.2Sr0.8MnO3-La0.3Sr0.7TiO3 Bilayer Coatings Along with the Interface Healing Processing Applied as the High Dense Interconnector for Tubular Solid Oxide Fuel Cells

Plasma spray coating on interconnector toward promoted solid oxide fuel cells and solid oxide electrolysis cells

Atmospheric Plasma-Sprayed La0.3Sr0.7TiO3-δInterconnect for High-Temperature Solid Oxide Fuel Cells

Plasma-sprayed lanthanum-doped strontium titanate as an interconnect for solid oxide fuel cells: Effects of powder size and process conditions

Plasma-sprayed Bulk-Like Yttria-Stabilized Zirconia Coatings for Solid Oxide Fuel Cell Electrolytes Based on Liquid-Phase Sintering-Induced Interfacial Healing

Effects of protective coating prepared by atmospheric plasma spraying on planar SOFC interconnect

Design and Conductivity Optimization of La0.3Sr0.7TiO3/La0.8Sr0.2MnO3 Bi-Layer Structures As Tubular Segmented-in-series Solid Oxide Fuel Cell Interconnect☆

Optimization of Plasma-Sprayed Lanthanum Chromite Interconnector Through Powder Design and Critical Process Parameters Control

La 2 NiO 4+δ Infiltration of Plasma-Sprayed LSCF Coating for Cathode Performance Improvement

Characterization of the Microstructure and Electrical Conductivity of Plasma-Sprayed La0.5Sr0.5CoO3 Coating

Effect of Spray Parameters on the Electrical Conductivity of Plasma-Sprayed La1−xSrxMnO3 Coating for the Cathode of SOFCs

LSM Protective Coatings on Stainless Steel As Interconnects for Solid Oxide Fuel Cells

Evaluation of Protective La0.67Sr0.33MnO3–δ Coatings on Various Stainless Steels Used for Solid Oxide Fuel Cell Interconnects

Microstructure Development For Application Of Thermal Sprayed Ceramic Coatings To Manufacturing Of Solid Oxide Fuel Cells

Enhancing Plasma-Sprayed LSCF Cathode Performance by Infiltration Method

Plasma Spraying of Ceramic Coatings and Their Applications to Solid Oxide Fuel Cells

Protective coating based on manganese–copper oxide for solid oxide fuel cell interconnects: Plasma spray coating and performance evaluation

Evaluation of Lanthanum Ferrite Coated Interconnect for Intermediate Temperature Solid Oxide Fuel Cells

Microstructure and Electrochemical Behavior of La0.8Sr0.2MnO3 Deposited by Solution Precursor Plasma Spraying

Conducting Property and Performance Evaluation of LNF As Cathode Current Contact Layer in Solid Oxide Fuel Cell

Novel Approaches to Prepare the High Performance Dense Electolyte and Interconnect Applicable to SOFC by Atmospheric Plasma Spraying