Abstract:A graded anode-supported solid oxide fuel cell (SOFC) with the structure porous Ni-yttria stabilized zirconia (Ni-YSZ)vertical bar microporous Ni-YSZ vertical bar YSZ vertical bar La0.8Sr0.2MnO3 (LSM) was fabricated by a trilayer co-pressing-sintering method, and coating with an LSM cathode. Cu-CeO2 was impregnated into the porous Ni-YSZ layer using nitrate/glycol precursors to act as an anti-carbon catalyst to fabricate a graded Cu-CeO2-NiO-YSZ composite anode. The current-voltage (I-V), current-power (I-P), and long-term stability of the SOFC were tested using CH4 or H-2 as fuels and air as an oxidant. The results show that the co-pressing-sintering layers possess a gradient pore structure with defect-free combination. The power density of SOFC supported by a graded Ni-YSZ anode is 284 mW.cm(-2), operated at 850 degrees C using H-2 as a fuel, but decreases to 143 mW.cm(-2) when the fuel is changed to CH4. In contrast, the cell supported by a Cu-CeO2-Ni-YSZ anode show the reverse behavior, increasing from 176 to 196 mW.cm(-2) when the fuel is changed from H-2 to CH4 at 850 degrees C. Under a 250 mA.cm(-2) load using CH4 as the fuel, the output of the cell with a graded Ni-YSZ anode fluctuats and the cell is blocked after 10 h. At this point, carbon particles or fibers are observed in the anode layer by scanning electron microscopy (SEM). Conversely, the cell with a Cu-CeO2-Ni-YSZ anode shows stable power output for 50 h or longer, and no carbon deposition was observed inside the anode.

Comparative study on the performance of tubular solid oxide fuel cells with various Pr0.35Nd0.35Sr0.3MnO3/YSZ cathode layers made by different processes

Effect of Cathode Fabrication Method on Characteristics of Anode-Supported Tubular Solid Oxide Fuel Cells

A Comparison of La0.75Sr0.25Cr0.5Mn0.5O3−δ and Ni Impregnated Porous YSZ Anodes Fabricated in Two Different Ways for SOFCs

Electrochemical Characteristics of Solid Oxide Fuel Cell Cathodes Prepared by Infiltrating (la,sr)mno3 Nanoparticles into Yttria-Stabilized Bismuth Oxide Backbones

High Performance Anode-Supported Tubular Solid Oxide Fuel Cells Fabricated by a Novel Slurry-Casting Method

Synthesis and electrochemical properties of (Pr-Nd)1-ySryMnO3-δ and (Pr1-xNdx)0.7Sr0.3MnO3-δ as cathode materials for IT-SOFC

Fabrication and performance of La0.8Sr0.2MnO3/YSZ graded composite cathodes for SOFC

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

High-performance cathode-supported SOFCs prepared by a single-step co-firing process

Preparation of Pr0.35Nd0.35Sr0.3MnO3−δ/YSZ Composite Cathode Powders for Tubular Solid Oxide Fuel Cells by Microwave-Induced Monomer Gelation and Gel Combustion Synthesis Process

Thin Yttria-Stabilized Zirconia Electrolyte and Transition Layers Fabricated by Particle Suspension Spray

Preparation, Evaluation, and Application of SUS430/441 Interconnect with Mn-Co Coating in Solid Oxide Fuel Cells

Performance of Tubular Solid Oxide Fuel Cell Assembled with Plasma-Sprayed Sc2O3–ZrO2 Electrolyte

High performance solid oxide fuel cells with electrocatalytically enhanced (La, Sr)MnO3 cathodes

Comparative study on the performance of tubular and button cells with YSZ membrane fabricated by a refined particle suspension coating technique

Improvement of Cathode–electrolyte Interfaces of Tubular Solid Oxide Fuel Cells by Fabricating Dense YSZ Electrolyte Membranes with Indented Surfaces

Comparative Study of Solid Oxide Fuel Cells Supported on Ceramic Cathodes with Different Pore Structures

Study on Preparation of YSZ Film by Electrophoretic Deposition under Constant Current and Its Application in SOFCs

Preparation and Properties of Direct-Methane Solid Oxide Fuel Cell Based on a Graded Cu-CeO<sub>2</sub>-Ni-YSZ Composite Anode

Performance Evaluation of Solid Oxide Fuel Cells with Thin Film Electrolyte Fabricated by Binder‐Assisted Slurry Casting

Composition optimization of samarium strontium manganite-yttria stabilized zirconia cathode for high performance intermediate temperature solid oxide fuel cells