Abstract:Proton-conducting solid oxide fuel cells, incorporating BaZr0.1Ce0.7Y0.2O3−δ (BZCY) electrolyte, NiO–BZCY anode, and Sm0.5Sr0.5CoO3−δ–Ce0.8Sm0.2O2−δ (SSC–SDC) cathode, were successfully fabricated by a combined co-pressing and printing technique after a one-step co-firing process at 1100, 1150, or 1200°C. Scanning electron microscope (SEM) results revealed that the co-firing temperature significantly affected not only the density of the electrolyte membrane but the grain size and porosity of the electrodes. Influences of the co-firing temperature on the electrochemical performances of the single cells were also studied in detail. Using wet hydrogen (2% H2O) as the fuel and static air as the oxidant, the cell co-fired at 1150°C showed the highest maximum power density (PDmax) of 552 and 370mWcm−2 at 700 and 650°C, respectively, while the one co-fired at 1100°C showed the highest PDmax of 276 and 170mWcm−2 at 600 and 550°C, respectively. The Arrhenius equation was proposed to analyze the dependence of the PDmax on the operating temperature, and revealed that PDmax of the cell co-fired at a lower temperature was less dependent on operating temperature. The influences of the co-firing temperature on the resistances of the single cells, which were estimated from the electrochemical impedance spectroscopy measured under open circuit conditions, were also investigated.

Effect of Cathode Fabrication Method on Characteristics of Anode-Supported Tubular Solid Oxide Fuel Cells

Fabrication and Properties of Anode-Supported Solid Oxide Fuel Cell

Scandia-stabilized Zirconia-Impregnated (la, Sr)MnO 3 Cathode for Tubular Solid Oxide Fuel Cells

Comparative study on the performance of tubular solid oxide fuel cells with various Pr0.35Nd0.35Sr0.3MnO3/YSZ cathode layers made by different processes

Preparation and Performance of Tri-layer Composite Anode Supported Fuel Cell

Fabrication and Electrochemical Characterization of Anode-Supported Microtubular Solid Oxide Fuel Cells Based on Ce0.8sm0.2o2-D Electrolytes

Fabrication and Characterization of a Small Tubular Solid Oxide Fuel Cell with the La0.43Ca0.37Ni0.06Ti0.94O3-γ Anode

Evaluation of BaZr0.1Ce0.7Y0.2O3−δ-based Proton-Conducting Solid Oxide Fuel Cells Fabricated by a One-Step Co-Firing Process

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Cathode Water Management Towards Improved Performance of Protonic Ceramic Fuel Cells

High Performance Tubular Solid Oxide Fuel Cells With Bscf Cathode

Effect of Fabrication and Operating Parameters on Electrochemical Property of Anode and Cathode for Direct Methanol Fuel Cells

Improvement of Cathode–electrolyte Interfaces of Tubular Solid Oxide Fuel Cells by Fabricating Dense YSZ Electrolyte Membranes with Indented Surfaces

Preparation and Performance of Nanostructured Porous Thin Cathode for Low-Temperature Solid Oxide Fuel Cells by Spin-Coating Method

Improvement of the Performances of Tubular Solid Oxide Fuel Cells by Optimizing Co-Sintering Temperature of the NiO/YSZ Anode-Ysz Electrolyte Double Layers

Preparation of SDC Interlayer and Influence on Performances of Anode Supported Solid Oxide Fuel Cells

Fabrication And Performance Of Anode-Supported Proton Conducting Solid Oxide Fuel Cells Based On Bazr0.1ce0.7y0.1yb0.1o3-Delta Electrolyte By Multi-Layer Aqueous-Based Co-Tape Casting

Improvement of output performance of solid oxide fuel cell by optimizing the active anode functional layer

Improvement of Anode-Supported Solid Oxide Fuel Cells

Effect of Low Plasma Spraying Power on Anode Microstructure and Performance for Metal-Supported Solid Oxide Fuel Cells

Preparation and performance of a nano-honeycomb cathode for microtubular solid oxide fuel cells