Abstract:Proton-conducting solid oxide fuel cells, incorporating BaZr0.1Ce0.7Y0.2O3−δ (BZCY) electrolyte, NiO–BZCY anode, and Sm0.5Sr0.5CoO3−δ–Ce0.8Sm0.2O2−δ (SSC–SDC) cathode, were successfully fabricated by a combined co-pressing and printing technique after a one-step co-firing process at 1100, 1150, or 1200°C. Scanning electron microscope (SEM) results revealed that the co-firing temperature significantly affected not only the density of the electrolyte membrane but the grain size and porosity of the electrodes. Influences of the co-firing temperature on the electrochemical performances of the single cells were also studied in detail. Using wet hydrogen (2% H2O) as the fuel and static air as the oxidant, the cell co-fired at 1150°C showed the highest maximum power density (PDmax) of 552 and 370mWcm−2 at 700 and 650°C, respectively, while the one co-fired at 1100°C showed the highest PDmax of 276 and 170mWcm−2 at 600 and 550°C, respectively. The Arrhenius equation was proposed to analyze the dependence of the PDmax on the operating temperature, and revealed that PDmax of the cell co-fired at a lower temperature was less dependent on operating temperature. The influences of the co-firing temperature on the resistances of the single cells, which were estimated from the electrochemical impedance spectroscopy measured under open circuit conditions, were also investigated.

High-performance cathode-supported SOFCs prepared by a single-step co-firing process

Low-temperature Solid Oxide Fuel Cells with Novel La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode and Functional Graded Anode

An ammonia fuelled SOFC with a BaCe0.9Nd0.1O3-δ thin electrolyte prepared with a suspension spray

A cathode-supported SOFC with thin Ce0.8Sm0.2O1.9 electrolyte prepared by a suspension spray

Proton-conducting Solid Oxide Fuel Cells Prepared by a Single Step Co-Firing Process

Preparation and Performance of Nanostructured Porous Thin Cathode for Low-Temperature Solid Oxide Fuel Cells by Spin-Coating Method

Fabrication and Electrochemical Characterization of Anode-Supported Microtubular Solid Oxide Fuel Cells Based on Ce0.8sm0.2o2-D Electrolytes

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing

Low Temperature Solid Oxide Fuel Cells with Hierarchically Porous Cathode Nano-Network

Micro-Tubular Solid Oxide Fuel Cell with Asymmetric Structure Anode and La0.6Sr0.4Co0.8Cu0.2O3−δ Perovskite Cathode

Facile preparation of electrodes of efficient electrolyte-supported solid oxide fuel cells using a direct assembly approach

High Performance of Proton-Conducting Solid Oxide Fuel Cell with a Layered PrBaCo2O5+δ Cathode

Electrochemical Performance of a Solid Oxide Fuel Cell Based on Ce0.8Sm0.2O2−δ Electrolyte Synthesized by a Polymer Assisted Combustion Method

High performance proton-conducting solid oxide fuel cells with a stable Sm0.5Sr0.5Co3-δ-Ce0.8Sm0.2O2-δ composite cathode

Evaluation of BaZr0.1Ce0.7Y0.2O3−δ-based Proton-Conducting Solid Oxide Fuel Cells Fabricated by a One-Step Co-Firing Process

Preparation of SDC Interlayer and Influence on Performances of Anode Supported Solid Oxide Fuel Cells

High performance layered SmBa0.5Sr0.5Co2O5+δ cathode for intermediate-temperature solid oxide fuel cells

Preparation and characterization of nanocrystalline Ce0.8Sm0.2O1.9 for low temperature solid oxide fuel cells based on composite electrolyte

Metal-supported Solid Oxide Fuel Cell with L a 0.4 Sr 0.6 Co 0.2 Fe 0.7 Nb 0.1 O 3-Δ Cathode

SrCo0.9Sb0.1O3–δ Cubic Perovskite As a Novel Cathode for Intermediate-to-low Temperature SOFCs

High Performance Solid Oxide Fuel Cells Based on Tri-Layer Yttria-Stabilized Zirconia by Low Temperature Sintering Process