Abstract:Proton-conducting solid oxide fuel cells, incorporating BaZr0.1Ce0.7Y0.2O3−δ (BZCY) electrolyte, NiO–BZCY anode, and Sm0.5Sr0.5CoO3−δ–Ce0.8Sm0.2O2−δ (SSC–SDC) cathode, were successfully fabricated by a combined co-pressing and printing technique after a one-step co-firing process at 1100, 1150, or 1200°C. Scanning electron microscope (SEM) results revealed that the co-firing temperature significantly affected not only the density of the electrolyte membrane but the grain size and porosity of the electrodes. Influences of the co-firing temperature on the electrochemical performances of the single cells were also studied in detail. Using wet hydrogen (2% H2O) as the fuel and static air as the oxidant, the cell co-fired at 1150°C showed the highest maximum power density (PDmax) of 552 and 370mWcm−2 at 700 and 650°C, respectively, while the one co-fired at 1100°C showed the highest PDmax of 276 and 170mWcm−2 at 600 and 550°C, respectively. The Arrhenius equation was proposed to analyze the dependence of the PDmax on the operating temperature, and revealed that PDmax of the cell co-fired at a lower temperature was less dependent on operating temperature. The influences of the co-firing temperature on the resistances of the single cells, which were estimated from the electrochemical impedance spectroscopy measured under open circuit conditions, were also investigated.

Proton-conducting Solid Oxide Fuel Cells Prepared by a Single Step Co-Firing Process

An ammonia fuelled SOFC with a BaCe0.9Nd0.1O3-δ thin electrolyte prepared with a suspension spray

Evaluation of BaZr0.1Ce0.7Y0.2O3−δ-based Proton-Conducting Solid Oxide Fuel Cells Fabricated by a One-Step Co-Firing Process

High-performance cathode-supported SOFCs prepared by a single-step co-firing process

High Performance of Proton-Conducting Solid Oxide Fuel Cell with a Layered PrBaCo2O5+δ Cathode

Optimization of BaZr0.1Ce0.7Y0.2O 3-δ-based proton-conducting solid oxide fuel cells with a cobalt-free proton-blocking La0.7Sr0.3FeO 3-δ-Ce0.8Sm0.2O2-δ composite cathode

Fabrication of BaZr0.1Ce0.7Y0.2O3 – Δ ‐based Proton‐Conducting Solid Oxide Fuel Cells Co‐Fired at 1,150 °C

In situ drop-coated BaZr0.1Ce0.7Y0.2O3-δ electrolyte-based proton-conductor solid oxide fuel cells with a novel layered PrBaCuFeO5+δ cathode

A High-Performing Proton-Conducting Solid Oxide Fuel Cell with Layered Perovskite Cathode in Intermediate Temperatures

Optimization of Sintering Temperature for SOFCs by a Co-Firing Method

Nano-sized Sm0.5Sr0.5CoO3-δ as the cathode for solid oxide fuel cells with proton-conducting electrolytes of BaCe0.8Sm0.2O2.9

Pr doped barium cerate as the cathode material for proton-conducting SOFCs

Sm0.5Sr0.5CoO3−δ–BaCe0.8Sm0.2O3-δ composite cathodes for proton-conducting solid oxide fuel cells

A novel single phase cathode material for a proton-conducting SOFC

Low-temperature co-sintering of co-ionic conducting solid oxide fuel cells based on Ce 0.8 Sm 0.2 O 1.9 -BaCe 0.8 Sm 0.2 O 2.9 composite electrolyte

Fabrication and Evaluation of a Ni/La0.75Sr0.25Cr0.5Fe0.5O3−δ Co-Impregnated Yttria-Stabilized Zirconia Anode for Single-Chamber Solid Oxide Fuel Cells

A Novel Co-firing Process for Multi-layers of Solid Oxide Fuel Cells

Enhancing chemical stability and performance in proton-conducting solid oxide fuel cells through novel composite cathode design

Novel cobalt-free cathode materials BaCexFe1-xO3-δ for proton-conducting solid oxide fuel cells

Characterization and evaluation of NdBaCo2O5+δ cathode for proton-conducting solid oxide fuel cells

Electrochemical Property of Multi-Layer Anode Supported Solid Oxide Fuel Cell Fabricated Through Sequential Tape-Casting and Co-Firing