Abstract:In this paper, the influence of internal oxidation of the bond-coat on the residual stress around the thermally grown oxide (TGO) and failure modes of the TBCs fabricated by atmospheric plasma spraying (APS) has been studied via finite element modeling. Generally, the internal oxidation will occur when the bond-coat (BC) was fabricated by APS. The produced oxide was distributed irregularly at the inner of the bond-coat, and the distribution patterns like some isolated islands, so it was called "island-like" oxide by us. As the BC layer usually consists Ni, Co, Cr, Al and Y etc., the composition of the "island-like" oxide is very complicated due to the formation Gibbs free energy are different when those metallic elements take reaction with exterior [O]. During the subsequent high temperature service conditions, a continuous thin TGO layer will be formed. In addition, the BC layer will be further endured with inner oxidation due to the [O] diffuse to the interface, the mixture oxide will appear below the TGO layer randomly, which will lead to a complicated stress distribution at the TGO/YSZ interface directly. Moreover, a small amount of Cr2O3 was formed in TGO layer, the distribution of interfacial stress was strongly influenced, resulting in complicated fluctuance of interface and unpredictable failure modes simultaneously. So, to systematically discuss the distribution of residual stress state along YSZ/TGO interface, the influence of the composition of TGO and the location of internal oxides on the distribution of interfacial stress were studied via FEM. The results show that with the increase of the percentage of Cr2O3 (wt.%) in TGO, the maximum tensile stress and compressive stress have changed evidently at the peak of TGO. Besides of considering the percentage of Cr2O3 (wt.%) in TGO, the internal oxides existed below the TGO layer have been taken into account simultaneously.

Evaluation of TGO Growth in Thermal Barrier Coatings Using Impedance Spectroscopy

TGO stress growth for Pt-modified aluminide bond coats during high temperature oxidation

Non-destructive Evaluation of Thermally Grown Oxides in Thermal Barrier Coatings Using Impedance Spectroscopy

The Impedance Spectroscopy Study of the Oxides Layer in Thermal Barrier Coatings

Influence factors of high temperature oxidation for Pt-modified-aluminide bond coatings

Different Growth Mechanisms of Alumina on the Surface of NiPtAl and MCrAlY Bondcoatings in EB-PVD TBC System

Isothermal oxidation and TGO growth behavior of NiCoCrAlY-YSZ thermal barrier coatings on a Ni-based superalloy

Influence of Composition of TGO on the Thermal Shock Lifetime of Thermal Barrier Coatings with Cold-Sprayed MCrAlTaY Bond Coat

High‐temperature oxidation and TGO growth behavior of Sr.9(Zr.9Yb.05Y.05)O2.85 thermal barrier coatings

High-temperature Oxidation and TGO Growth Behavior of Sr.9(Zr.9Yb.05Y.05)O2.8 5 Thermal Barrier Coatings

Effect of TGO on the Tensile Failure Behavior of Thermal Barrier Coatings

Isothermal Oxidation Behavior of Supersonic Atmospheric Plasma-Sprayed Thermal Barrier Coating System

Mechanism of Interface Morphology of YSZ Thermal Barrier Coating on Growth Behavior of TGO Layer

Influence of Pretreatment on the Growth Behavior of TGO on MCrAlY Bond Coat Surface

A Study of the Microstructure and Oxidation Behavior of Alumina/yttria-Stabilized Zirconia (al2o3/ysz) Thermal Barrier Coatings

Effects of TGO growth on the interface stress distribution based on 3D pores in TBC ceramics layer

Effect of TGO Thickness on Thermal Cyclic Lifetime and Failure Mode of Plasma‐Sprayed TBCs

Isothermal Oxidation TGO Growth Behaviors of Laser-Remolten LZO/YSZ Thermal Barrier Coatings

Effect of TGO Thickness on Isothermal Cyclic Lifetime of Plasma-Sprayed YSZ Thermal Barrier Coatings

Effects of TGO growth on the stress distribution and evolution of three-dimensional cylindrical thermal barrier coatings based on finite element simulations

Influence of Internal Oxidation of the Bond-Coat on the Residual Stress Around the TGO and Failure Modes of the APS-TBCs: A Finite Element Simulation Study