Abstract:Features peculiar to the synthesis of SiC–Si 3 N 4 –Si 2 N 2 O composite powder with a controlled content of silicon carbide, nitride, and oxynitride phases, as well as the structure and properties of hot-pressed ceramics produced from this powder, were examined. The optimal composition of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O powder was achieved by heating a 1 : 3 mixture of thermally expanded graphite (TEG) and silicon up to 1200°C in air. The interaction of TEG with fine silicon at 1200°C led to the formation of a solid solution of carbon in silicon carbide, accompanied by heat release. The generated heat increased temperature within localized volumes of the TEG cellular structure to a level where air nitrogen facilitated the development of silicon nitride and oxynitride and an amorphous phase. The amorphous phase crystallized as the interaction time increased to 2.5 h. The duration of the process influenced the final distribution of the phases, formed with the participation of CO, SiO, and air nitrogen. The microstructure of the synthesized powder was characterized by a general agglomerated state, resulting from rod and plate forms of Si 3 N 4 and Si 2 N 2 O. Hot pressing of the synthesized SiC–Si 3 N 4 –Si 2 N 2 O composite powder with Al 2 O 3 and Y 2 O 3 activators yielded superfine ceramics, possessing enhanced hardness and fracture toughness (HV10 = 20.7 GPa and K Ic = 6.5 MPa · m 1/2 ). The structure of the ceramics sintered at 2000°C differed from those sintered at 1850°C, primarily by higher density and average grain size. The superfine state significantly influenced the abrasive wear resistance of the ceramics in dry friction conditions. The linear wear index of a sample with an average size of structural elements varying from 0.2 to 1.5 μm was 111 μm/km at a sliding speed of 1 m/sec under a load of 0.2 MPa. This was significantly lower than the linear wear index of industrial ceramics of reaction-sintered silicon carbide (RSSC), which was 232.4 μm/km.

Preparation and Properties of SiC Refractories Via Carbonization-Nitridation Reaction

Optimization of Microstructure to Improve Si3n4 Ceramics with Thermal Conductivity and Mechanical Properties: Effect of Si and Α-Si3n4 Powder Composition

Preparation And Properties Of Sintering-Free Low Density Si3n4/Sic Composite Refractory

Effect of Silicon Addition on Mechanical Properties of Mullite-Sic Composite Refractories

Fabrication and Properties of Al<sub>2</sub>O<sub>3</sub>-SiC/Sialon Composite Refractories

Catalytic Preparation of Si3N4-Bonded SiC Refractories and Their High-Temperature Properties

Fabrication and properties of Al 2O 3-SiC/Sialon composite refractories

Preparation of Sialon/Si<sub>3</sub>N<sub>4</sub>-SiC Composite Refractories Using Kyanite Tailings

In Situ Catalytic Synthesis of Si3N4 Nanowhiskers Reinforced SiC Refractories and Their High-Temperature Properties

Fabrication and Properties of Si<sub>3</sub>N<sub>4</sub>-SiC-C Refractory Composites

Phase Behavior of Silica Brick Used in Carbothermal Reduction

Fabrication of novel AlN-SiC-C refractories by nitrogen gas-pressure sintering of Al4SiC4

Preparation of Sialon/Si3N4-SiC Composite Refractories Using Kyanite Tailings

Si3N4-SiCpComposites Reinforced Byin SituCo-Catalyzed Generated Si3N4Nanofibers

Carbothermally prepared nanophase SiC/ Si3N4 composite powders and densified parts

Phase evolution mechanism of SiC-Al-Si composite under flowing nitrogen at 1600 °C

Study on In-Situ Reaction Synthesis and Mechanical Properties of Si2N2O Ceramic

Novel (Zr, Ti)(C, N)–SiC ceramics via reactive hot-pressing at low temperature

Preparation and Properties of Si<sub>3</sub>N<sub>4</sub>-SiC-C Refractory Materials Composited with Sucrose and Phenolic Resin

Synthesis and Consolidation of Composite Materials in the SiC–Si3N4–Si2N2O System

Preparation of ZrN-SiAlON-SiC composite refractories with sucrose as bonding agent