Abstract:With the advancement of semiconductor manufacturing technology, thin film structures were widely used in MEMS devices. These films played critical roles in providing support, reinforcement, and insulation in MEMS devices. However, due to their microscopic dimensions, the sensitivity of their parameters and performance to thermal stress increased significantly. In this study, a Pirani gauge sample with a multilayer thin film structure was designed and fabricated. Based on this sample, finite element modeling analysis and thermal stress experiments were conducted. The finite element modeling analysis employed a combination of steady-state and transient methods to simulate the deformation and stress distribution of the device at room temperature (25 °C), low temperature (−55 °C), and high temperature (125 °C). The thermal stress test involved placing the sample in a temperature cycling chamber for temperature cycling tests. After the tests, the resonant frequency and surface deformation of the device were measured to quantitatively evaluate the impact of thermal stress on the deformation and resonant frequency parameters of the device. After the experiments, it was found that the clamped-end beams made of Pt were a stress concentration area. Additionally, the repetitive thermal load caused the cantilever beam to move cyclically in the Z direction. This movement altered the deformation of the film and the resonant frequency. The suspended film exhibited concavity, and the overall trend of the resonant frequency was downward. Over time, this could even lead to the fracture of the clamped-end beams. The variation of mechanical parameters derived from finite element simulations and experiments provided an important reference value for device design improvement and played a crucial role in enhancing the reliability of thin film devices.

Characterization of the Variation of the Material Properties in a Freestanding Inhomogeneous Thin Film

High-frequency Permeability Spectra of FeCoSiN/Al2O3 Laminated Films: Tuning of Damping by Magnetic Couplings Dependent on the Thickness of Each Ferromagnetic Layer

Cut-Off Frequencies of Lamb Waves in Various Functionally Graded Thin Films

Calculation of propagation properties of Lamb waves in a functionally graded material (FGM) plate by power series technique

Variation of MEMS Thin Film Device Parameters under the Influence of Thermal Stresses

Thickness-shear Frequencies of an Infinite Quartz Plate with Material Property Variation Along the Thickness

Simultaneous Measurement of Local Longitudinal and Transverse Wave Velocities, Attenuation, Density, and Thickness of Films by Using Point-Focus Ultrasonic Spectroscopy

Mems/Nems Mechanical Characterization on Different Thin - Film Materials by Scanning along Micro-Machined Cantilevers

A Novel Technique for the Measurement of the Acoustic Properties of a Thin Linear-Viscoelastic Layer Using a Planar Ultrasonic Transducer

Simultaneous Measurement of Elastic Moduli, Attenuation, Density, and Thickness of a Layer by Ultrasonic Spectroscopy Using Point-Focus Transducer

Wentzel–Kramers–Brillouin Solution of Cut-off Frequency for Horizontal Shear (SH) Waves in Various Inhomogeneous Thin Films

Lamb Wave Propagation in the Functionally Graded Piezoelectric–piezomagnetic Material Plate

Nano-sculptured thin film thickness variation with incidence angle

SIMULTANEOUS MEASUREMENTS OF THE MAGNETOSTRICTIVE COEFFICIENT,YOUNG'S MODULUS AND POISSON RATIO OF THE THIN FILM CONSIDERING THE THICKNESS OF FILM

Mechanical characterization of biocompatible thin film materials by scanning along micro-machined cantilevers for micro-/nano-system

Lamb Wave Propagation in a Functionally Graded Piezoelectric- Piezomagnetic Material Plate

Tunable Three-Dimensional Vibrational Structures for Concurrent Determination of Thin Film Modulus and Density

Modification of curvature-based thin-film residual stress measurement for MEMS applications

Asymptotic Analytical Solution on Lamb Waves in Functionally Graded Nano Copper Layered Wafer

Elastic and elastic-plastic analysis of multilayer thin films filled with heterogeneous materials

Nanomechanical Characterisation of MEMS Thin Film Materials